HP Designjet T1120 1118 mm User Manual

Introduction
This chapter describes various printer settings that the printer administrator may wish to control as soon
as a new printer is assembled and ready for use.
Handle paper conflicts
If the paper currently loaded in the printer is not suitable for a particular job, the printer can either put
the job on hold until some suitable paper is loaded, or it can ignore the problem and print the job on the
unsuitable paper. There are several ways in which the loaded paper may be considered unsuitable:...

In each case, you will see the following options:
●In order: pages are nested in the order in which they are sent to the printer. The nested pages are
printed as soon as one of three conditions is met:
◦The next page will not fit on the same row as the other pages already nested.
◦No page has been sent to the printer during the specified wait time.
◦The next page is incompatible with the pages already nested (see 
Nest jobs to save roll
paper on page 64).
●Optimized order: pages are not necessarily...

Turn alerts on and off
Printer alerts warn you when there is a printer problem that you can correct by taking action, or when
one of your printing jobs changes its status. The alerts are displayed by the printers front panel, by the
HP Printer Utility, by the printer driver and by the Embedded Web Server.
You can tell the printer which kinds of alerts you would like to see (if any). To access the alert settings:
●Select Alert Settings in the Device List page of the HP Printer Utility.
●Select Alert...

Require account ID
If you want to keep records of printer usage by different user accounts, you can set your printer to require
an account ID for each job.
●In the HP Printer Utility for Windows: select Settings > Accounting > Require account ID.
●In the HP Printer Utility for Mac OS: select Configuration > Printer Settings > Configure
Printer Settings > Accounting > Require account ID.
If this setting is turned on, the account ID field will be mandatory and jobs with no account ID will be
kept on hold...

26 Chapter 3   Setting up the printer ENWW
Setting up the printer
 

4 Personalizing the printer
●Turn the printer on and off
●
Change the language of the front-panel display
●
Access the HP Printer Utility
●
Access the Embedded Web Server
●
Change the language of the HP Printer Utility
●
Change the language of the Embedded Web Server
●
Change the sleep mode setting
●
Turn the buzzer on and off
●
Change the front-panel display contrast
●
Change the units of measurement
●
Configure network settings
●
Change the graphic language setting
ENWW27
Personal settings
 

Turn the printer on and off
TIP:The printer can be left powered on without wasting energy. Leaving it on improves response time
and overall system reliability. When the printer has not been used for a certain period of time, it saves
power by going into sleep mode. However, any interaction with the printers front-panel display returns
it to active mode, and it can resume printing immediately. To change the sleep mode time, see 
Change
the sleep mode setting on page 30.
NOTE:In sleep mode, the printer...

When the printer is powered back on, it takes about three minutes to initialize and check and prepare
the printheads. Preparing the printheads takes about one minute and 15 seconds. However, if the printer
has been off for six weeks or more, preparing the printheads could take up to 45 minutes.
Change the language of the front-panel display
There are two possible ways to change the language of the front-panel menus and messages.
●If you can understand the current front-panel display language, press the...

To access the Embedded Web Server on any computer, open your Web browser and give the address
of your printer. You can find out the address of your printer (starting with http:) from the front-panel
display, by looking at the status screen.
If you have followed these instructions but failed to get through to the Embedded Web Server, see
Cannot access the Embedded Web Server on page 178.
Change the language of the HP Printer Utility
The HP Printer Utility can work in the following languages: English,...

Change the front-panel display contrast
To change the contrast of the front-panel display, select the Setup menu icon , then Front panel
options > Select display contrast, and enter a value using the Up or Down key. Press the OK key to
set the value. The default contrast is set to 50.
Change the units of measurement
To change the units of measurement in the front-panel display, select the Setup menu icon ,
then Front panel options > Select units, and select English or Metric. By default the units are set...