HP DesignJet 8000sr User Manual

2 How do I… (basic operation topics)?
●Connect to a computer
● Turn the power on/off
● Check the firmware version
Connect to a computer
This section describes syst
em configuration and cable connec tion procedures.
NOTEBefore connecting or disconnecting t he USB Cable, turn the printer OFF.
System configuration (connection example)
The following connection is possible.
1.Printer server (RIP).
2. USB interface.
3. Printer.
Connection procedure
NOTE Before you connect the USB cable, you should  ensure...

Connect a USB cable as follows:
1.Disconnect the USB cable from the rear of  your printer if it is already connected.
2. Press the  POWER ON/OFF  key (1) on the front panel to turn the printer off.
NOTEOnly turn off the printer while  PRINTER READY is displayed on the front panel
except in an emergency. Do not turn off the printer while  INITIALIZING or CLEANING  is
displayed on the front panel to avoid liquid  dripping onto other parts of the printer and
damage to the printhead.
3. Power off the...

5.Connect the USB cable (2) to the USB co nnector (1) at the rear of the printer.
6.Attach the USB cable with the two cabl e clamps at the rear of the printer.
7. Power on the printer using the power switch (1) at the rear.
ENWW Connect to a computer 13
How do I… (basic operation
to
pics
)?
 

8.Press the  POWER ON/OFF  key (1) on the front panel to turn the printer on.
9.Follow the instructions on your computer in order to select the printer.
Turn the power on/off
WARNING! Use the power supply voltage  specified on the nameplate.
Be sure the printer is well-grounded. Failure to  ground the printer may result in electrical shock,
fire, and susceptibility to electromagnetic interference.
CAUTION Always hold the power cable by the plug when connecting and disconnecting from
the power outlet....

Turn on the printer
1.Power off the printer using the power switch at the r ear of the printer, and plug one end of the supplied
power cable (1) into the socket of the printer. Insert  the other end of the cable into an electrical outlet.
WARNING!Avoid overloading the printer’s electrical  outlet with multiple devices. Use only
the electrical cable supplied by HP with the prin ter. Do not damage, cut, or repair the power
cable. A damaged power cable has risk of fire  and electric shock. Replace a...

3.Press the  POWER ON/OFF  key (1) on the front panel.
When you press power on, the printer performs a  power-on self-diagnostic test and the following
messages are displayed on the front panel.
(If a 64 media roll is loaded).
NOTE Only turn off the printer while  PRINTER READY is displayed on the front panel
except in an emergency. Do not turn off the printer while  INITIALIZING or CLEANING  is
displayed on the front panel to avoid liquid  dripping onto other parts of the printer and
damage to the...

WARNING!The printer has an internal clock which allows it to automatically wash the
printheads, flushing some ink through the pr intheads, which keeps the printheads in good
condition. The printer automatically washes the  printheads regularly after the last printing
process. If the printer is switched Off for a long  period, this process does not happen. If the ink
does not flow through the printheads from time to  time, the ink will dry inside the nozzles, reaching
a point where it is impossible to...

Check the firmware version
To check the firmware version on your printer do the following:
1.Press the  ONLINE key to take the printer online.
2. Press the  SHIFT key to display the  SETUP menu.
3.Press the  key to select the  SETUP menu.
4. Scroll to  PRINTER FW VER  and press OK.
NOTEFor information on firmware updates and installation instructions, see Tell me about…(getting help topics)
18 Chapter 2   How do I… (basic operation topics)? ENWW
How do I… (basic operation
to
pics
)?
 

3 How do I load/unload media
This section describes how to load and remove media in the printer.
●Install a media roll in the printer
● Remove a media roll from the printer
● Replace a jammed media roll
● Load a cut sheet
● Use the media edge guards
● Use the media cutter
● Use the take-up reel
ENWW 19
How do I load/unload media
 

Install a media roll in the printer
CAUTIONDo not touch heater surfaces in t he media path. This may cause burns.
Handle media rolls with care. They can be heavy and  difficult to move in confined spaces. In some
cases, two people should move and install media rolls. Dropping a media roll could cause
personal injury or damage to the printer.
NOTE You can increase or reduce the printhead height depending on the thickness of the media
you are using. See How do I… Change the printhead height
.
NOTE The HP...