HP DesignJet 70 User Manual

HP Designjet 70/110plus Printer series—Quick Reference Guide
10 If your printer has two slots, you must feed the sheet through the upper slot (the 
lower slot is for roll paper only).
4. Align the left edge of the paper with the left mark on the rear feed. If you do 
not see a mark, align it with the paper stop near the left-hand end of the roll 
feed spindle. Make sure that the leading edge of the sheet is parallel to the 
slot, and not skewed.
5. Push the paper into the printer, pushing it as far as it...

HP Designjet 70/110plus Printer series—Quick Reference Guide
11 The printer output system has several adjustable components. When printing on 
large sheets of paper, it is important that you use the correct printer output 
configuration. The following diagram shows adjustable parts of the printer output 
system:
The table on the next page gives the output system configuration required for 
various paper sizes.
Note:
• When using the input tray or roll feed as the paper source, make the necessary...

HP Designjet 70/110plus Printer series—Quick Reference Guide
12
Media
Source Destination Size Width Length 1 2 3 4 5 6
Input trayOutput 
trayA-SizeJIS B5 182mm 257mm
UPPo s i ti o n  
A3, ...Closed DOWN Closed N/A ANSI A 8.5’’ 11’’
ISO A4 210mm 297mm
ARCH A 9’’ 12’’
DIN C4 229mm 324mm
ISO B4 250mm 353mm
UPPo s i ti o n  
B4, ...ClosedDOWNClosedN/A LEGAL 8.5’’ 14’’
JIS B4 257mm 364mm
B-SizeISO A3 297mm 420mm
UPPo s i ti o n  
A3, ...Po s i t io n  
A3, ...DOWN Closed N/A
ANSI B 11’’ 17’’
ARCH B 12’’ 18’’...

HP Designjet 70/110plus Printer series—Quick Reference Guide
13
How do I print on large sheets? (110plus Printer series)
The printer output system has several adjustable components. When printing on 
large sheets of paper, it is important that you use the correct printer output 
configuration. The following diagram shows adjustable parts of the printer output 
system:
The table on the next page gives the output system configuration required for 
various paper sizes.
Note:
• When using the input tray or...

HP Designjet 70/110plus Printer series—Quick Reference Guide
14
Media
Source Destination Size Width Length 1 2 3 4 5 6
Input trayOutput 
trayA-SizeJIS B5 182mm 257mm
UPPo s i t i o n  
A3, ...Closed DOWN Closed N/A ANSI A 8.5’’ 11’’
ISO A4 210mm 297mm
ARCH A 9’’ 12’’
DIN C4 229mm 324mm
ISO B4 250mm 353mm
UPPo s i t i o n  
B4, ...ClosedDOWNClosedN/A LEGAL 8.5’’ 14’’
JIS B4 257mm 364mm
B-SizeISO A3 297mm 420mm
UPPo s i t i o n  
A3, ...Po s i t io n  
A3, ...DOWN Closed N/A
ANSI B 11’’ 17’’
ARCH B 12’’...

HP Designjet 70/110plus Printer series—Quick Reference Guide
15 Roll paper can be used only if you have the roll feed accessory.
Note that only one source of paper can be used by the printer at any time. So if a 
roll of paper is loaded in the printer and you want to print to a sheet of paper, you 
must first unload the roll. If subsequent jobs require a roll to be used, the roll must 
be loaded again before they can be printed.
You can cut a roll without unloading it by pressing the OK key; the paper...

HP Designjet 70/110plus Printer series—Quick Reference Guide
16 6. Rewind any excess paper so that the paper is rolled tightly onto the spindle.
7. Insert the leading edge of the paper into the rear 
of the printer until it encounters resistance, 
keeping the sides of the paper rolled tightly so 
that the paper is properly aligned.
8. After emitting a ‘beep’ the printer will take up the 
paper.
9. The printer will check the alignment of the paper.
If the roll is properly aligned, the roll icon will...

HP Designjet 70/110plus Printer series—Quick Reference Guide
17 Important: do not pull on the roll of paper once it is taken up by the printer; that 
is, if there is any resistance.
1. Press the Cancel and OK keys at the same time to eject the roll of paper.
2. Pull the roll towards you and remove the paper completely from the rear paper 
path of the printer. The icons shown below flashes until the paper is completely 
out; because, if the paper is only partially removed, paper jams may 
subsequently...

HP Designjet 70/110plus Printer series—Quick Reference Guide
18 This section is only relevant if your printer has a roll feed installed.
Only one source of paper can be used by the printer at any one time, so if a roll 
of paper is loaded and the software requests printing on a sheet of 
paper:
• If you have a manual roll feed installed on your printer, you must unload the roll 
manually before you can print to a sheet of paper. 
• If you have the Automatic Roll Feed installed on your printer, the roll...

HP Designjet 70/110plus Printer series—Quick Reference Guide
19 If the paper is glossy, we recommend that you wear gloves to avoid smearing 
the surface of the paper.
5. Make sure that the leading edge of the roll is straight and perpendicular to its 
side edges.
6. Rewind any excess paper so that the paper is rolled tightly onto the spindle.
7. Insert the leading edge 
of the paper into the 
lower slot in the rear of 
the printer. Push the 
paper in until it 
encounters resistance, 
keeping the sides of...