HP DesignJet 70 User Manual

HP Designjet
70/110plus series
Quick reference guide
 

1
How do I…?
How do I load sheets of paper? (general guidance).............................................3
How do I load paper using the front path? .........................................................5
How do I unload paper from the front path? .......................................................5
How do I load paper into the input tray? ............................................................6
How do I load sheet paper using the rear path?...

HP Designjet 70/110plus Printer series—Quick Reference Guide
2
More information
For more information about your printer (including Windows and Mac drivers 
and networking information) and troubleshooting printer problems, refer to the HP 
Designjet Driver and Documentation CD. For additional information about the 
Windows driver, use the on-line help for the driver.
The information contained herein is subject to change without notice. The only 
warranties for HP products and services are set forth in the...

HP Designjet 70/110plus Printer series—Quick Reference Guide
3 There are four ways of loading sheets of paper into the printer if you have the 
Automatic Roll Feed installed on your printer. There are three ways of loading 
paper if you have the manual roll feed or no roll feed installed:
1. The input tray at the front of the printer for multiple sheets of paper between 
76×142mm (3×5.6inches) and 457×610 mm (18×24inches) (C+).  
Envelopes can also be loaded in the input tray.
2. Th e front path for...

HP Designjet 70/110plus Printer series—Quick Reference Guide
4 The roll feed enables you to load roll paper into the rear path. When roll paper is 
loaded into the printer, it obstructs the paper path; therefore roll paper must always 
be unloaded before printing on sheet paper (see page 18).
However the paper is loaded, it should always be loaded in portrait mode: the 
leading edge of the paper should be the shorter edge.
The extensions may be used to support large sheets of paper going into the front...

HP Designjet 70/110plus Printer series—Quick Reference Guide
5
Note that the illustration below shows the HP Designjet 110plus Printer series.
1. Place a single sheet of paper in the output tray, aligning it on the right of the 
output tray, with the side that is to be printed on facing down. Do not stack 
multiple sheets here.
2. Push the paper as far as it will go into the printer, maintaining its alignment to 
the right. Ensure that your hands are flat on the paper and close to the slot, and 
that the...

HP Designjet 70/110plus Printer series—Quick Reference Guide
6
How do I load paper into the input tray?
Note that the input tray should be extended only when necessary: when using 
paper larger than Legal- or A4-size.
1. Remove the input tray.
2. Lift up the tray cover.
3. If the paper you are using is larger than Legal- or A4-size, move the small tab 
in the center towards the left so that you can lengthen the tray. Then let go of 
the tab and pull the tray extension out as far as it will go.
4. Fan the...

HP Designjet 70/110plus Printer series—Quick Reference Guide
7 5. Slide the paper into the tray under the tray cover, ensuring that it touches the 
sides of the tray on the right and on the printer side.
6. Push in the small tab on the right of the tray so that it fits snugly against the 
paper. Move the larger tab on the left of the tray to the right so that it too fits 
snugly against the paper.
7. Close the tray cover.
How do I load paper into the input tray? (continued)
 

HP Designjet 70/110plus Printer series—Quick Reference Guide
8 8. Lift up the output tray and insert the input tray into the printer, keeping it straight 
and pushing it in from both sides as far as it will go. The left inside corner must 
be aligned with the plastic paper tray guide and the right inside corner must be 
aligned with the sticker of the input tray.
9. Lower the output tray, pushing the tray slightly to the left. Note that if the input 
tray is extended, it will extend out beyond the output...

HP Designjet 70/110plus Printer series—Quick Reference Guide
9 In order to print on sheet paper using the rear path, you must submit your print job 
to the printer before loading the paper.
1. Set the paper source to Rear Manual Feed. If you leave the paper source set to 
Auto Select (Windows) or Automatic (Mac OS), the printer will start printing on 
any paper that is already loaded. If you specify Rear Manual Feed, you do not 
need to remove paper from the tray before using the rear path.
2. Submit...