HP DesignJet 130nr User Manual

QRG100p.fm  Page 1  Monday, December 8, 2003  2:03 PM
HP Designjet 130/130nr
Quick reference guide
Guide de référence rapide
Guida di riferimento rapido Kurzreferenz
Guía de referencia rápida
 

QRG100p.fm  Page 1  Monday, December 8, 2003  2:03 PM
 

HP Designjet 130/130nr - Quick Reference Guide
EnglishHow Do I...?
How Do I Perform a Color Calibration? .............................................. 3
How Do I Load Sheets of Paper? (General Guidance) .......................... 4
How Do I Load Paper Using the Front Path? ........................................ 5
How Do I Unload Paper from the Front Path? ...................................... 5
How Do I Load Paper in the Input Tray? ............................................. 6
How Do I Load a Roll...

HP Designjet 130/130nr Printer - Quick Reference Guide2
EnglishImportant Note: To ensure color consistenc y, you must perform a color 
calibration at various times. See “Tell  Me About Color Calibration” on page 42.
More information. For more information about your printer (including 
Mac driver and networking  information), and troubleshooting printer problems, 
refer to the  Using Your Printer  CD. For information about the Windows driver, 
use the on-line help for the driver. 
The information...

HP Designjet 130/130nr Printer - Quick Reference Guide
3
English
How Do I Perform a Color Calibration?
To ensure that color consistency is maintained, you will need to perform a color 
calibration at various times (for example, when you change the printheads). For 
more information on when you should perform a color calibration, refer to “Tell 
Me About Color Calibration” on page 42. 
The calibration is performed for a given combination of printheads and paper 
type. After you have done the calibration,...

HP Designjet 130/130nr Printer - Quick Reference Guide
4
EnglishHow Do I Load Sheets of Paper? (General Guidance)
There are three ways of loading sheets of paper into the printer (note that the 
diagram below shows the printer with the Automatic Roll Feed installed):
The tray at the front of the printer for normal sheets of paper between 
76 x 142 mm (3 x 5.6 inches) and 457 x 610 mm (18 x 24 inches) (C+ or 
A2+); envelopes can also be loaded in the input tray.
The front path for paper between 110 x...

HP Designjet 130/130nr Printer - Quick Reference Guide
5
English
How Do I Load Paper Using the Front Path?
4. Place a piece of paper on the output tray, aligning it on the right of the 
output tray, with the side that is to be printed facing down. Do NOT stack 
paper.
5. Push the paper into the printer, pushing it firmly in as far as it will go, while 
maintaining its alignment to the right. Slide the tab on the left of the paper 
until it is holding the paper against the right side of the tray.
6. Press...

HP Designjet 130/130nr Printer - Quick Reference Guide
6
EnglishHow Do I Load Paper in the Input Tray?
1. Remove the tray from the printer.
2. Remove the dust cover from the tray. Adjust the size of the tray if necessary. If 
the paper you are using is larger than Legal- or A4-size, extend the tray. For 
Legal- and A4-size or smaller paper, use the tray in its normal size. To adjust 
the size of the tray, slide the tray extension locking tab to the left until it 
clicks. This unlocks the tray extension....

HP Designjet 130/130nr Printer - Quick Reference Guide
7
English
How Do I Load Paper in the Input Tray? (continued)
...continued from previous page...
4. Push in the small tab on the right of the tray so that it fits snugly against the 
paper.
5. Move the larger tab on the left of the tray to the right so that it fits snugly 
against the paper. Replace the dust cover. Insert the tray into the printer, 
pushing it in as far as it will go. Note that if the paper tray is extended, it 
will project out from...

HP Designjet 130/130nr Printer - Quick Reference Guide
8
EnglishHow Do I Load a Roll of Paper?
This section is only relevant if your printer has the Automatic Roll Feed installed.
Only one source of paper can be used by the printer at any one time, so if a 
roll of paper is loaded in the printer and you want to print to a sheet of paper, 
you must first unload the roll. The roll is automatically reloaded the next time 
printing to the roll is requested.
You can cut a roll without unloading it by pressing...