HP Compaq Presario W19q User Guide

 
w19b / w19e / W19q LCD Monitor 
User’s Guide 
• Preface 
• 
Safety and Maintenance Guidelines 
• 
Setup 
• 
Using the Monitor 
• 
Installing Drivers and Using the Auto-Adjustment Feature 
• 
Technical Support FAQs 
• 
Specifications 
• 
LCD Monitor Quality and Pixel Policy 
• 
Agency Regulatory Notices 
  
The only warranties for HP products and services are set forth in the express warranty statements accompanying such 
products and services. Nothing herein should be construed as constituting an...

 
 
Back to Contents Page 
Preface 
About This Guide • Notational Conventions 
 
About This Guide 
This guide is intended for anyone who uses the w19b / w19e / W19q LCD Monitor. It describes the monitor’s 
features, setup, and operation. 
The sections are as follows: 
• Safety and Maintenance Guidelines 
• Setup 
• Using the Monitor 
• Installing Drivers and Using the Auto-Adjustment Feature 
• Technical Support FAQs 
• Specifications 
• LCD Monitor Quality and Pixel Policy 
• Agency Regulatory Notices...

 
 
Back to Contents Page 
Safety and Maintenance Guidelines 
Important Safety InformationSafety PrecautionsMaintenance GuidelinesCleaning the Monitor  
 
Important Safety Information 
The power cord is designed for use with your monitor. To use a different cord, use only a power source and 
connection compatible with this monitor. For information on the correct power cord set to use with your monitor, 
see Power Cord Set Requirements
. 
 
 
WARNING: To reduce the risk of electric shock or damage to your...

 
 
Maintenance Guidelines 
To enhance the performance and extend the life of your monitor:  
• Do not open your monitor cabinet or attempt to service this product yourself. If your monitor is not operating 
properly or has been dropped or damaged, contact your Hewlett-Packard authorized dealer, reseller, or 
service provider. 
• Adjust only those controls that are described in the operating instructions. 
• Turn your monitor off when not in use. You can substantially increase the life expectancy of your...

 
  
Back to Contents Page 
Setup 
Base and TiltCablesWall Mounting Arm 
 
Base and Tilt 
Attaching the BaseRemoving the BaseAdjusting the Tilt 
 
Attaching the Base 
1 Set the panel face-down on a flat, protected 
surface. 
2 Align the pedestal slots with the panel tabs and 
insert (A). 
3 Slide the pedestal to the right to lock it into 
place (B). 
4 Lift the panel and lower the pedestal onto the base 
until the push tab locks. 
 
 
 
WARNING: Be careful to avoid pinching or scraping fingers when...

 
 
Removing the Base 
1 Push the release tab and raise the pedestal off the base. 
   
 
 
2 Set the panel face-down on a flat, protected 
surface. 
3 Slide the pedestal to the left to unlock it from the 
base (A). 
4 Remove the pedestal from the panel (B). 
 
WARNING: Be careful to avoid pinching 
or scraping fingers when attaching the 
base. 
 
 
CAUTION: To prevent damage, avoid 
applying pressure to the panel front. 
  
 

 
 
Adjusting the Tilt 
For optimal viewing, adjust the screen tilt to your own preference, as follows: 
1 Face the front of the monitor and hold the stand so that you do not topple the monitor while changing the tilt. 
2 Adjust the tilt by moving the monitor’s top edge toward or away from you. 
 
 
 
 CAUTION: To avoid breakage or other damage, do not touch the LCD screen while 
changing the tilt. 
 
 

 
  
Back to Contents Page 
Cables 
Attaching the Cables 
 
Attaching the Cables 
You can attach a VGA cable (provided), a DVI-D cable (select models only), or both to this monitor. To use DVI, 
your computer must have a DVI-compliant graphics card. Connectors are found on the back of the monitor. 
If both cables are installed, the source of input can be selected using the Input Select option in the OSD menu. 
Please refer to the OSD Menu
 section.  
1 Turn off your computer. 
2 Connect the built-in...

  3 If you are attaching a VGA cable, connect one end of the 15-pin D-Sub VGA cable (blue connector) to the 
back of the monitor and connect the other end to the computer VGA port. 
 
 
4 If you are attaching a DVI cable, connect one end of the 24-pin DVI cable (white connector) to the back of the 
monitor (select models only) and connect the other end to the computer DVI port. 
 
 
 

 5 Connect one end of the power cord to the back of the monitor and plug the other end into a grounded outlet. 
 
  
6 Secure the cables by routing them through the clasp. 
 
 
7  Turn on your monitor and computer. 
If your monitor displays an image, installation is complete. If it does not display an image, see Technical Support 
FAQs and Using the Monitor.