HP Color LaserJet CM3530 MFP User Manual

Menu itemSub-menu itemSub-menu itemValues and Description
  HTTP TestThis test checks operation of HTTP by retrieving
predefined pages from the product, and tests the
embedded Web server.
Select Yes to choose this test, or  No to not choose it.
  SNMP TestThis test checks operation of SNMP communications
by accessing predefined SNMP objects on the product.
Select  Yes to choose this test, or  No to not choose it.
  Data Path TestThis test helps to identify data path and corruption
problems on an HP...

Menu itemSub-menu itemSub-menu itemValues and Description
  ExecuteSpecify whether to initiate the ping test. Select Yes to
initiate the test, or  No to not run the test.
 Ping Results Use this item to view the ping test status and results
using the control panel display. You can select the
following items:
Packets SentShows the number of packets (0 - 65535) sent to the
remote host since the most recent test was initiated or
completed.
Packets ReceivedShows the number of packets (0 - 65535) received...

Menu itemSub-menu itemSub-menu itemValues and Description
100TX Auto: Limits auto-negotiation to a maximum link
speed of 100 Mbps.
1000TX Full: 1000 Mbps, full-duplex operation.
Print Protocols   Use this item to print a page that lists the configuration
of the following protocols: IPX/SPX, Novell NetWare,
AppleTalk, DLC/LLC.
Table 2-11  Jetdirect menus (continued)
ENWW Initial Setup menu 39
 

Fax Setup
Administration > Initial Setup  > Fax Setup
NOTE: This menu is available only for the HP Color LaserJet CM3530fs MFP.
Table 2-12   Fax Setup menu
Menu itemSub-menu itemSub-menu itemValuesDescription
Fax Setup Wizard   Use this wizard to set up options for sending
faxes if the analog fax accessory is installed.
Required SettingsCountry/Region (Countries/regions
listed)Configure the settings that are legally
required for outgoing faxes.
Date/Time  
Fax Header
InformationTelephone Number
Company...

Menu itemSub-menu itemSub-menu itemValuesDescription
Fax Send Settings Fax Dial Volume Off
Low (default)
HighUse this feature to set the volume of the tones
that you hear while the product dials the fax
number.
Error Correction
Mode Enabled (default)
DisabledWhen  Error Correction Mode  is enabled and
an error occurs during fax transmission, the
product sends or receives the error portion
again.
JBIG Compression Enabled  (default)
DisabledJBIG compression reduces fax-transmission
time, which can result...

Menu itemSub-menu itemSub-menu itemValuesDescription
 Redial Interval The range is between
1 and 5 minutes. The
factory default is 5
minutes.Use this feature to specify the number of
minutes between dialing attempts if the
recipient number is busy or not answering.
Detect Dial Tone Enabled
Disabled (default)Use this feature to specify whether the
product should check for a dial tone before
sending a fax.
Dialing Prefix Off (default)
CustomUse this feature to specify a prefix number
that must be dialed...

E-mail Setup
Administration > Initial Setup  > E-mail Setup
Use this menu to enable the e-mail feature and to configure basic e-mail settings.
NOTE: To configure advanced e-mail settings, use the embedded Web server. For more information,
see 
Embedded Web server on page 169.
Table 2-13   E-mail Setup menu
Menu itemValuesDescription
E-mail Setup Wizard Use this wizard to set up basic options for the e-mail feature.
Address ValidationOn  (default)
OffThis option enables the product to  check e-mail syntax...

Device Behavior menu
Administration > Device Behavior
Table 2-15  Device Behavior  menu
Menu itemSub-menu itemSub-menu itemValuesDescription
Language  Select the language
from the list.Select a different language for control-panel
messages. When you select a new language,
the keyboard layout might also change.
Keyboard Layout  Select the keyboard
layout from the listSelect a keyboard layout regardless of the
Language setting.
Select  Default  if you want the keyboard layout
to change when the  Language...

Menu itemSub-menu itemSub-menu itemValuesDescription
Tray BehaviorUse Requested Tray Exclusively (default)
FirstControl how the product handles jobs that
have specified a spec ific input tray.
Manually Feed
Prompt Always (default)
Unless LoadedSpecify how a prompt should appear when
the type or size for a job does not match the
specified tray and the product pulls from the
multipurpose tray instead.
PS Defer Media Enabled  (default)
DisabledSelect either the PostScript (PS) or HP
paper-handling model....

Menu itemSub-menu itemSub-menu itemValuesDescription
General Printing
BehaviorOverride A4/Letter No
Yes
 (default)When this feature is enabled, the job prints
on letter-size paper when an A4 job is sent
but no A4-size paper is loaded in the product
(or prints on A4 paper when a letter-size job
is sent but no letter-size paper is loaded).
This option also overrides A3 with ledger-size
paper and ledger with A3-size paper.
Manual Feed Enabled
Disabled  (default)When this feature is enabled, the user can...