HP 5500 Ei 5500 Si Switch Series Configuration Guide

 78 
GigabitEthernet 1/0/2 as the secondary port. Specify Device G as the master node of subring 4, 
GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port. 
Specify Device H as the master node of subring 5, GigabitEthernet 1/0/1 as the primary port and 
GigabitEthernet 1/0/2 as the secondary port. 
•   Specify Device A as the edge node of the connected subrings, its GigabitEthernet 1/0/3 and 
GigabitEthernet 1/0/4 as the edge ports. Specify Device D as the transit node...

 79 
to 802.1p priority. Configure the four ports as trunk ports, and assign them to VLANs 1 through 
30.  
[DeviceA] interface gigabitethernet 1/0/1 
[DeviceA-GigabitEthernet1/0/1] undo link-delay 
[DeviceA-GigabitEthernet1/0/1] undo stp enable 
[DeviceA-GigabitEthernet1/0/1] qos trust dot1p 
[DeviceA-GigabitEthernet1/0/1] port link-type trunk 
[DeviceA-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30 
[DeviceA-GigabitEthernet1/0/1] quit 
[DeviceA] interface gigabitethernet 1/0/2...

 80 
[DeviceA-rrpp-domain1] quit 
# Enable RRPP.  
[DeviceA] rrpp enable 
2. Configure Device B: 
# Create VLANs 1 through 30, map these VLANs  to MSTI 1, and activate the MST region 
configuration. 
 system-view 
[DeviceB] vlan 1 to 30 
[DeviceB] stp region-configuration 
[DeviceB-mst-region] instance 1 vlan 1 to 30 
[DeviceB-mst-region] active region-configuration 
[DeviceB-mst-region] quit 
# Cancel the physical state change suppression in terval setting on GigabitEthernet 1/0/1 through...

 81 
[DeviceB-rrpp-domain1] protected-vlan reference-instance 1 
# Configure Device B as the transit node of primary ring 1, with GigabitEthernet 1/0/1 as the 
primary port and GigabitEthernet 1/0/2 as  the secondary port, and enable ring 1.  
[DeviceB-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1 
secondary-port gigabitethernet 1/0/2 level 0 
[DeviceB-rrpp-domain1] ring 1 enable 
# Configure Device B as the assistant-edge node of subring 2, with GigabitEthernet 1/0/4 as the...

 82 
[DeviceC-GigabitEthernet1/0/3] undo stp enable 
[DeviceC-GigabitEthernet1/0/3] qos trust dot1p 
[DeviceC-GigabitEthernet1/0/3] port link-type trunk 
[DeviceC-GigabitEthernet1/0/3] port trunk permit vlan 1 to 30 
[DeviceC-GigabitEthernet1/0/3] quit 
[DeviceC] interface gigabitethernet 1/0/4 
[DeviceC-GigabitEthernet1/0/4] undo link-delay 
[DeviceC-GigabitEthernet1/0/4] undo stp enable 
[DeviceC-GigabitEthernet1/0/4] qos trust dot1p 
[DeviceC-GigabitEthernet1/0/4] port link-type trunk...

 83 
[DeviceD] interface gigabitethernet 1/0/1 
[DeviceD-GigabitEthernet1/0/1] undo link-delay 
[DeviceD-GigabitEthernet1/0/1] undo stp enable 
[DeviceD-GigabitEthernet1/0/1] qos trust dot1p 
[DeviceD-GigabitEthernet1/0/1] port link-type trunk 
[DeviceD-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30 
[DeviceD-GigabitEthernet1/0/1] quit 
[DeviceD] interface gigabitethernet 1/0/2 
[DeviceD-GigabitEthernet1/0/2] undo link-delay 
[DeviceD-GigabitEthernet1/0/2] undo stp enable...

 84 
[DeviceD] rrpp enable 
5. Configure Device E: 
# Create VLANs 1 through 30, map these VLANs  to MSTI 1, and activate the MST region 
configuration. 
 system-view 
[DeviceE] vlan 1 to 30 
[DeviceE] stp region-configuration 
[DeviceE-mst-region] instance 1 vlan 1 to 30 
[DeviceE-mst-region] active region-configuration 
[DeviceE-mst-region] quit 
# Cancel the physical state change suppression  interval setting on GigabitEthernet 1/0/1 and 
GigabitEthernet 1/0/2, disable the spanning tree fe ature, and...

 85 
[DeviceF-mst-region] instance 1 vlan 1 to 30 
[DeviceF-mst-region] active region-configuration 
[DeviceF-mst-region] quit 
# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and 
GigabitEthernet 1/0/2, disable the spanning tree fe ature, and set the trusted packet priority type 
to 802.1p priority. Configure the two ports as trunk ports, and assign them to VLANs 1 through 
30.  
[DeviceF] interface gigabitethernet 1/0/1 
[DeviceF-GigabitEthernet1/0/1] undo...

 86 
[DeviceG-GigabitEthernet1/0/1] undo link-delay 
[DeviceG-GigabitEthernet1/0/1] undo stp enable 
[DeviceG-GigabitEthernet1/0/1] qos trust dot1p 
[DeviceG-GigabitEthernet1/0/1] port link-type trunk 
[DeviceG-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30 
[DeviceG-GigabitEthernet1/0/1] quit 
[DeviceG] interface gigabitethernet 1/0/2 
[DeviceG-GigabitEthernet1/0/2] undo link-delay 
[DeviceG-GigabitEthernet1/0/2] undo stp enable 
[DeviceG-GigabitEthernet1/0/2] qos trust dot1p...

 87 
[DeviceH-GigabitEthernet1/0/2] undo stp enable 
[DeviceH-GigabitEthernet1/0/2] qos trust dot1p 
[DeviceH-GigabitEthernet1/0/2] port link-type trunk 
[DeviceH-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30 
[DeviceH-GigabitEthernet1/0/2] quit 
# Create RRPP domain 1. Configure VLAN 4092 as the primary control VLAN of RRPP domain 1, 
and configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.  
[DeviceH] rrpp domain 1 
[DeviceH-rrpp-domain1] control-vlan 4092...