HP 5500 Ei 5500 Si Switch Series Configuration Guide

 68 
Step Command Remarks 
1.  Enter system view.  system-view  N/A 
2.  Enable RRPP. 
rrpp enable  Disabled by default. 
3.  Enter RRPP domain view. 
rrpp domain domain-id   N/A 
4.  Enable the specified RRPP 
ring.  ring 
ring-id  enable  Disabled by default. 
 
Configuring RRPP timers 
Perform this configuration on the master node of an RRPP domain.  
To  c o n fig u re  R R PP  t i me rs : 
 
Step Command Remarks 
1.  Enter system view. 
system-view  N/A 
2.  Enter RRPP domain view.  rrpp domain...

 69 
•  Make sure that all subrings in an RRPP ring group have the same SRPTs. If the SRPTs of these 
subrings are configured or modified differently,  the RRPP ring group cannot operate properly.  
Configuration procedure 
To configure an RRPP ring group:  
Step Command 
1.  Enter system view. 
system-view 
2.  Create an RRPP ring group and enter RRPP ring 
group view.  rrpp ring-group 
ring-group-id 
3.  Assign the specified subrings to the RRPP ring 
group.  domain 
domain-id  ring ring-id-list...

 70 
Figure 20 Network diagram 
 
 
Configuration procedure 
1. Configure Device A: 
# Create VLANs 1 through 30, map these VLANs  to MSTI 1, and activate the MST region 
configuration. 
 system-view 
[DeviceA] vlan 1 to 30 
[DeviceA] stp region-configuration 
[DeviceA-mst-region] instance 1 vlan 1 to 30 
[DeviceA-mst-region] active region-configuration 
[DeviceA-mst-region] quit 
# Cancel the physical state change suppression  interval setting on GigabitEthernet 1/0/1 and 
GigabitEthernet 1/0/2, disable...

 71 
[DeviceA-rrpp-domain1] protected-vlan reference-instance 1 
# Configure Device A as the master node of primary ring 1, with GigabitEthernet 1/0/1 as the 
primary port and GigabitEthernet 1/0/2 as  the secondary port, and enable ring 1.  
[DeviceA-rrpp-domain1] ring 1 node-mode master primary-port gigabitether\
net 1/0/1 
secondary-port gigabitethernet 1/0/2 level 0 
[DeviceA-rrpp-domain1] ring 1 enable 
[DeviceA-rrpp-domain1] quit 
# Enable RRPP.  
[DeviceA] rrpp enable 
2. Configure Device B: 
#...

 72 
# Enable RRPP.  
[DeviceB] rrpp enable 
3. Configure Device C: 
The configuration on Device C is similar to  that on Device B and is not shown here.  
4. Configure Device D: 
The configuration on Device D is similar to  that on Device B and is not shown here. 
5. Verify the configuration: 
Use the  display command to view RRPP configuration and  operational information on each device. 
Intersecting ring configuration example 
Networking requirements 
As shown in Figure 21,  
•   D
evice A, Device B,...

 73 
# Create VLANs 1 through 30, map these VLANs to MSTI 1, and activate the MST region 
configuration. 
 system-view 
[DeviceA] vlan 1 to 30 
[DeviceA] stp region-configuration 
[DeviceA-mst-region] instance 1 vlan 1 to 30 
[DeviceA-mst-region] active region-configuration 
[DeviceA-mst-region] quit 
# Cancel the physical state change suppression  interval setting on GigabitEthernet 1/0/1 and 
GigabitEthernet 1/0/2, disable the spanning tree fe ature, and set the trusted packet priority type 
to 802.1p...

 74 
# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1, 
GigabitEthernet 1/0/2, and GigabitEthernet 1/0/3,  disable the spanning tree feature, and set 
the trusted packet priority type to 802.1p priority . Configure the three ports as trunk ports, and 
assign them to VLANs 1 through 30.  
[DeviceB] interface gigabitethernet 1/0/1 
[DeviceB-GigabitEthernet1/0/1] undo link-delay 
[DeviceB-GigabitEthernet1/0/1] undo stp enable 
[DeviceB-GigabitEthernet1/0/1] qos trust...

 75 
[DeviceC-mst-region] instance 1 vlan 1 to 30 
[DeviceC-mst-region] active region-configuration 
[DeviceC-mst-region] quit 
# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1, 
GigabitEthernet 1/0/2, and GigabitEthernet 1/0/3,  disable the spanning tree feature, and set 
the trusted packet priority type to 802.1p priority . Configure the three ports as trunk ports, and 
assign them to VLANs 1 through 30.  
[DeviceC] interface gigabitethernet 1/0/1...

 76 
# Create VLANs 1 through 30, map these VLANs to MSTI 1, and activate the MST region 
configuration. 
 system-view 
[DeviceD] vlan 1 to 30 
[DeviceD] stp region-configuration 
[DeviceD-mst-region] instance 1 vlan 1 to 30 
[DeviceD-mst-region] active region-configuration 
[DeviceD-mst-region] quit 
# Cancel the physical state change suppression  interval setting on GigabitEthernet 1/0/1 and 
GigabitEthernet 1/0/2, disable the spanning tree fe ature, and set the trusted packet priority type 
to 802.1p...

 77 
# Cancel the physical state change suppression interval setting on GigabitEthernet 1/0/1 and 
GigabitEthernet 1/0/2, disable the spanning tree fe ature, and set the trusted packet priority type 
to 802.1p priority. Configure the two ports as trunk ports, and assign them to VLANs 1 through 
30.  
[DeviceE] interface gigabitethernet 1/0/1 
[DeviceE-GigabitEthernet1/0/1] undo link-delay 
[DeviceE-GigabitEthernet1/0/1] undo stp enable 
[DeviceE-GigabitEthernet1/0/1] qos trust dot1p...