Honeywell V32fb9 Manual

							 
 
– 41 – 
Access Door Control 
General Information 
Your system may be set up such that a locked access door (such as in a lobby) 
can be unlocked momentarily or for a specific period of time, using a keypad 
command.  Ask your installer if this has been done in our system. 
Executing 
There are several entries that can be entered at the keypad to activate this 
command: 
1.  Enter your security code + [0].  The door will unlock for 2 seconds. 
2.  Enter your security code + [#] + 73, or security code + [#] + 74 + access 
point.  The door will unlock for a specific period of time. 
3.  Enter your security code + [#] + 75 + access point + function.  The 
functions available are Grant, Protect and Bypass.  Grant will 
temporarily unlock a door to allow an access.  Protect will cause a door to 
unlock only when a valid access is received.  Bypass will cause a door to 
be permanently unlocked to allow continuous access. 
4.  Access control functions may also be executed use your security code + [#] 
+ 77. See Using #77 Instant Activation Mode later in this manual. 
 
 
 
 
 
 
 
 
 
 
  
						

							 
 
– 42 – 
Using #70 Relay Menu Mode 
General Information 
Your system may be set up so that certain lights or other devices can be 
turned on or off by using the #70 command from either a keypad or a 
telephone keypad (if 4285 or 4286 VIP module is used). Ask your installer if 
this has been done in your system. 
To activate relays from a keypad, enter 4-digit security code + [#] +70. 
Follow the keypad prompts described below. 
To activate relays using a telephone and 4285 or 4286 VIP module, 
first dial the 2-digit phone access code. When the system acknowledges the 
access, enter 4-digit security code + [#] + 70. The following prompts/voice 
responses will begin. 
ENTER DEVICE NO. 
00=QUIT 01
Voice: ENTER DEVICE CODE NOW 
Enter the 2-digit number of the device to be activated. 
Note that if an invalid number is entered, the system 
will simply ask you to reenter the number. 
NN    DEVICE IS OFF 
HIT  0=OFF ,  1=ON 
Voice: voice descriptor  DEVICE nn ON/OFF.  FOR 
voice descriptor ON ENTER 1, FOR voice descriptor 
OFF ENTER 0 
Press 0 or 1 to turn the device off or on respectively. 
nn represents the 2-digit device number and voice 
descriptor is the relay voice descriptor programmed 
by the installer. 
NN    DEVICE IS OFF 
HIT THE ✴ KEY 
Voice: voice descriptor  DEVICE nn ON/OFF.  TO 
EXIT ENTER 00 NOW 
From a keypad, press ✴ to continue. The ENTER 
DEVICE NO. prompt will appear. 
From a telephone keypad, enter 00 to exit, or 
enter the next relay number to be programmed. The 
current on/off state of that relay will be annunciated 
as described above. Alternatively, if 6 seconds elapses 
with no key depression, the 4285 or 4286 VIP module 
will annunciate the ENTER DEVICE CODE NOW 
message.  
						

							 
 
– 43 – 
Using Schedules 
Delaying the Closing Time 
Your system’s programmed schedules may automatically arm the system at a 
predetermined time. In the event a user must stay on the premises later than 
usual, users with master or manager authority levels can manually delay the 
automatic arming (closing) time up to 2 hours. To delay the closing time: 
1.  Enter your security code (master or manager authority levels only). 
2. Press the  # 
 key, followed by 82. 
3.  A menu prompt will be displayed, asking for the number of hours of delay.  
 
CLOSING DELAY? 
KEY 0-2 HOURS 
Enter the desired number of hours of delay, 1 or 2. 
The system automatically exits this mode after 
entry.  
Note that the delay is from the scheduled closing time, not from the 
time the command is entered.  
IMPORTANT: The selected delay cannot be reduced once it is set. A 1 
hour delay can be increased to 2 hours, though. 
4.  The system will automatically send a message to the central station 
informing them that the programmed schedule has been changed. 
Temporary Open/Close Schedules 
Temporary schedules allow you to override the normal schedules 
programmed by the installer. Temporary schedules can be in effect for up to 
one week, and take effect as soon as they are programmed. 
They are comprised of an arming (closing) time window and a disarming 
(opening) time window. A time window is simply a defined period of time, at 
the end of which arming or disarming will occur. 
Before programming, use a worksheet similar to the one below to plan your 
schedule. This will make it easier when actually programming the schedule. 
Arm/Disarm Mon Tue Wed Thu Fri Sat Sun 
Windows 
       
Disarm Window 
       
 Start Time  HH:MM        
 Stop Time   HH:MM        
Arm Window 
       
 Start Time  HH:MM        
 Stop Time   HH:MM         
						

							 
 
– 44 – 
Using Schedules (cont’d) 
Programming Temporary Schedules 
Temporary schedules only affect the partition from which it is entered. 
Temporary schedules can be reused at later dates simply by scrolling (by 
pressing #) to the DAYS? prompt (described below) and activating the 
appropriate days. This should be considered when defining daily time 
windows. Note that only users with authority level of manager or higher can 
program temporary schedules. 
To program temporary schedules: 
1.  Enter your security code. 
2. Press the  #
  key followed by 81. 
3.  The following prompts will appear. 
MON  DISARM WIND. 
07:45AM  08:45AM 
The cursor will be positioned on the tens of hours 
digit of the start time for Monday’s disarm 
window. Enter the desired hour. Press * to move 
to the minutes field. The minutes are entered in 
the same manner. The AM/PM indication is 
changed by hitting any key, 0-9, while the cursor 
is under the letter A/P position. Repeat for the 
stop time entry. Press the * key to move  to the 
arming window for Monday. 
Press # to move to the next screen display 
without making changes. 
MON   ARM WINDOW  
07:45AM  08:45AM 
The cursor will be positioned on the tens of hours 
digit of the start time for the arm window. Repeat 
the previous steps to enter the start and stop 
time for Monday’s arming window. 
TUE  DISARM WIND. 
07:45AM  08:45AM 
After the windows for that day have been 
completed, the system will prompt for disarm and 
arm time windows for the next day. Repeat the 
procedure for all days of the week. 
When all of the days have been completed, the 
system will ask which days are to be activated. 
  
						

							 
 
– 45 – 
Using Schedules (cont’d) 
DAYS ?   MTWTFSS 
HIT 0-7  X   X 
This is the prompt that actually activates the 
temporary schedule, and allows the temporary 
schedule to be customized to a particular week’s 
needs. To select the days which are to be 
activated, enter the desired number 1-7 (Monday 
= 1). An X will appear under that day, 
indicating the previously entered schedule for 
that day is active. Entering a day’s number again 
will deactivate that day.  Pressing 0 will turn all 
days on/off. 
The temporary schedule will only be in effect for 
the days which have the letter x underneath 
them. As the week progresses, the days are reset 
to the deactive state. 
When completed, press * to exit the temporary 
schedule entry mode. 
  
						

							 
 
– 46 – 
Programming Device Timers 
General Information 
Device timers consist of an ON time & an OFF time, and selected days of the 
week in which they are active. There are up to 20 timers that can be used to 
control various devices, such as lights or appliances. Your installer will have 
programmed the appropriate devices into the system (up to 96 devices can be 
programmed).  
Each timer controls a single device (designated as an output number) that 
you select. For example, timer 1 might be set to turn the porch lights on at 
7:00pm and turn them off at 11:00pm. Timer 2 might turn on the air 
conditioner Monday-Friday at 4:30pm to cool the premises before you arrive 
at 5:00pm, and turn it off at 10:00pm when you are retiring for the night. If 
desired, different timers can control the same device. For example, timer 2 
could be used Monday-Friday as in the previous example, and timer 3 could 
be set to turn the air conditioner on and off at different times Saturday and 
Sunday. 
To enter the device timer menu mode:  
Enter your security code, then press the  # 
 key followed by 83. 
OUTPUT TIMER # ? 
01-20,00=QUIT 01 
Up to 20 timers can be programmed. Each timer 
is identified by a number 1-20. Enter the desired 
timer number to be programmed (1-20). Press * 
to accept entry. 
06 07:00P 11:45P 
PORCH LITE    04 
If that timer number has already been 
programmed, a summary screen will appear. In 
this example: 
  06 = Timer # 
  04 = Output Device # affected by this timer  
  PORCH LITE = Output Descriptor for Device 4 
  07:00PM = Start Time; 
  11:45PM = Stop Time 
Press * to continue.  
See your installer for 
device numbers. 00 ENTER OUTPUT# 
 00 
Enter the desired output device number (1-96). 
As the number is entered, the device’s description 
will appear. 
To delete a previously programmed timer, enter 
00 as the output number.  
						

							 
 
– 47 – 
Programming Device Timers (cont’d) 
 
00 ON TIME ? 
00:00 PM 
Enter the time you want the device turned on 
using 00:01 - 11:59 format. When the display 
shows the desired time, press the * key to move 
to the AM/PM field. Press any key 0-9 to change 
the AM/PM indication. 
Enter 00:00 if this timer is not being used to turn 
something ON for the days selected below. (ex. 
using one timer to turn lights on one day and 
using another timer to turn them off on another 
day). 
00 OFF TIME ? 
00:00 PM 
Enter the time you want the device turned off 
using 00:01 - 11:59 format. When the display 
shows the desired time, press the * key to move 
to the AM/PM field. Press any key 0-9 to change 
the AM/PM indication. 
Enter 00:00 if this timer is not being used to turn 
something OFF for the days selected below. (ex. 
using one timer to turn lights on one day and 
using another timer to turn them off on another 
day). 
00 DAYS? MTWTFSS 
HIT 0-7      X   X 
Select the days on which the device is to be 
activated by entering 1-7 (Monday = 1). An X 
will appear under that day, indicating the output 
for that day is active. Entering a day’s number 
again will deactivate that day. Pressing 0 will 
turn all days on/off. The outputs will only be in 
effect for the days  that have the letter x 
underneath them. As the week progresses, the 
days are reset to the inactive state, unless the 
permanent option is selected (next screen 
prompt). When completed, press * to continue.
 
00 PERMANENT ? 
0 = NO, 1 = YES     0 
Answering 1 (YES) means the system executes 
this timer continuously. Answering 0 (NO)means 
the system executes each day’s output only once. 
 
  
						

							 
 
– 48 – 
Using #77 Instant Activation Mode 
The #77 Instant Activation Mode is used to activate outputs, bypass zones, 
etc. immediately upon exiting the #77 Mode. The actions that may be 
activated are relay commands, arm/disarm commands, zone bypassing 
commands, and open/close access conditions. 
Relay Commands 
Action Code
 Action Specifier 
01   Relay On  Relay #  
02   Relay Off  Relay #   
03   Relay Close for 2 seconds  Relay #   
04   Relay Close XX minutes ✳ Relay # 
05   Relay Close YY seconds ✳ Relay # 
06   Relay Group On  Relay Group # 
07   Relay Group Off  Relay Group # 
08   Relay Group Close for 2 seconds  Relay Group # 
09   Relay Group Close XX minutes ✳  Relay Group # 
10   Relay Group Close YY seconds ✳  Relay Group # 
✳ Check with your installer for the amount of time. 
Arm/Disarm Commands 
Activation times 1 (Beginning), 2 (End), 3 (During) are the only valid choices 
for automatic arming and disarming functions. 
During can be used to arm or disarm the control for a specific time only.  
For example, if during is selected with Arm-STAY, the system will 
automatically Arm-STAY at the beginning of the window and automatically 
disarm at the end of the window. 
Action Code
 Action Specifier 
20   Arm-STAY  Partition(s) 
21   Arm AWAY  Partition(s) 
22   Disarm  Partition(s) 
23   Force Arm STAY (Auto-bypass faulted zns)   Partition(s) 
24   Force Arm AWAY (Auto-bypass faulted zns)  Partition(s) 
25 Arm INSTANT  Partition(s) 
26 Arm MAXIMUM  Partition(s) 
 
 
 
 
  
						

							 
 
– 49 – 
Using #77 Instant Activation Mode (cont’d) 
Bypass Commands 
Activation times 1 (Beginning), 2 (End), 3 (During) are the only valid choices 
for bypass commands.  If 3 (During) is selected for auto-bypassing, the 
system bypasses the zone(s) specified on a particular zone list at the 
beginning of the window and unbypasses them at the end of the window.  If it 
is selected for auto unbypassing, the system removes the bypass at the 
beginning of the window and restores the bypass at the end of the window. 
Action Code
 Action Specifier 
30   Auto bypass - Zone list  Zone list #  
31   Auto unbypass - Zone list  Zone list # 
Open/Close Windows 
Activation time 3 (During) is the only valid choice for these commands. 
Action Code
 Action Specifier 
40   Enable Opening Window by partition   Partition(s) 
41   Enable Closing Window by partition   Partition(s) 
42   Enable Access Window for access group  Access Group 
Access Control Commands 
Action Code
 Action Specifier 
55  Access Point Grant  Access Point # 
56  Access Point Grant with Override  Access Point # 
57  Access Point Protect  Access Point # 
58  Access Point Bypass  Access Point # 
59  Access Point Lock  Access Point # 
60  Access Point Exit  Access Point # 
61  Access Point Group Grant  Group # 
62  Access Point Group Grant with Override  Group # 
63  Access Point Group Protect  Group # 
64  Access Point Group Bypass  Group # 
66  Access Point Group Exit  Group # 
67  Access Point Partition Grant  Partition # 
68  Access Point Partition Grant with Override  Partition # 
69  Access Point Protect by Partition  Partition # 
70  Access Point Bypass by Partition  Partition # 
71  Access Point Lock by Partition  Partition # 
72  Access Point Exit by Partition  Partition # 
73  Access Point Trigger On  Trigger # 
74  Access Point Trigger Off  Trigger #  
						

							 
 
– 50 – 
Using #77 Instant Activation Mode (cont’d) 
Additional Commands 
Action Code
 Action Specifier 
77  Access Point Group Enable  Group # 
78  Access Point Group Disable  Group # 
To enter the Instant Activation Mode: 
Enter your security code, then press the [#] key followed by 77. 
 ACTION  ? 
 
Enter the code for the desired action. The 
action codes are the events that are to take place 
when either the system exits the #77 Mode or the 
scheduled time is reached, depending on the action 
selected.  
Press [✳] to continue. 
Enter the action specifier. This defines what the 
action will affect (relay, relay group, partition, zone 
list, user group). The action specifier screen prompt 
varies, depending on the type of action selected. 
As an example, if you selected “Auto Bypass” as the 
action, the action specifier prompt would be: 
  ZONE LIST  ? 
 
ARE YOU SURE ? 
1 = YES    0 = NO  0 
Enter 1 (YES) or 0 (NO). 
Press [✳] to continue.
 
QUIT MENU MODE? 
1 = YES    0 = NO 
Enter 1 (YES) or 0 (NO). 
Press [✳] to continue.