Honeywell Sundial RF Pack 4 Wireless Enabled Timer and Cylinder Thermostat User Manual

							User Guide
Y9120W Sundial RF2 Pack 4
How to use:
  ST9120C Wireless Enabled Timer
  CS92A Wireless Cylinder Thermostat
Honeywell Control Systems Ltd.
Arlington Business Park,
Bracknell
Berkshire
RG12 1EB
Technical Help Desk: 08457 678999
www.honeywelluk.com 50047645-002 A
© 2011 Honeywell International Inc.
System Components
Energy Efficiency and the Environment
Home energy use is responsible for more than ¼ of the total UK carbon emissions 
which contribute to climate change. Heating and hot water systems based on 
boilers account for 
 of this figure, so it is important to understand how your 
controls can help to maximize energy efficiency while maintaining your comf\
ort.
Your Timer should be used in conjunction with appropriate temperature controls. In 
order to save energy the following general points should be observed:
1.  Ensure your system contains a room thermostat (where appropriate) and a hot 
water thermostat, and that  it is set to an appropriate temperature level, typically 
20°C
2.  Programme your heating (and hot water) to be off when you are not in the 
house. If you are concerned about possible frost damage to any exposed pipe 
work, it is advisable to fit a frost protection system – your installer can advise 
you about this.
3.  Think about how you use your domestic hot water – if you have a stora\
ge 
system, it is not necessary to have this switched on all the time, even when you 
are in the house.
4.  Consider the heat up times required for your central heating. Every home 
responds differently when the heating is switched on. Adjust the start time so 
that you are not cold when you get up in the morning. A shorter heat up time is 
required for other heating periods.
5.  In the evening, when the house is up to temperature, it is often possible to 
switch off the heating up to an hour before you go to bed, without any noticeable 
reduction in comfort.
PLEASE RESPECT YOUR ENVIRONMENT!
Take care to dispose of this product and any 
packaging or literature in an appropriate way
This document is to be left with the user
and forms part of a Home Information Pack
WHAT IS A PROGRAMMER?
...an Explanation for Householders (as recommended by the Energy Savings Trust)Programmers allow you to set ‘On’ and ‘Off’ time periods. Some models switch the central heating and 
domestic hot water on and off at the same time, while others allow the domestic hot water and heatin\
g 
to come on and go off at different times. Set the ‘On’ and ‘Off’ time periods to suit your own lifestyle. On 
some programmers you must also set whether you want the heating and hot water to run continuously, 
run under the chosen ‘On’ and ‘Off’ heating periods, or be permanently 
off. The time on the programmer must be correct. Some types have to be 
adjusted in spring and autumn at the changes between Greenwich Mean 
Time and British Summer Time. You may be able to temporarily adjust the 
heating programme, for example, ‘Override’, ‘Advance’, or ‘Boost’\
. These 
are explained in the manufacturer’s instructions. The heating will not work 
if the room thermostat has switched the heating off. And, if you have a hot-
water cylinder, the water heating will not work if the cylinder thermostat 
detects that the hot water has reached the correct temperature.
WHAT IS A CYLINDER THERMOSTAT?
...an explanation for Householders (as recommended by the Energy Savings Trust)A cylinder thermostat switches on and off the heat supply from the boiler to the hot water cylinder. 
It works by sensing the temperature of the water inside the cylinder, switching on the water heating 
when the temperature falls below the thermostat setting, and switching it off once this set temperature 
has been reached.
Turning a cylinder thermostat to a higher setting will not make the water heat up any faster. How quickly 
the water heats up depends on the design of the heating system, for exam\
ple, the size of boiler and 
the heat exchanger inside the cylinder.
The water heating will not work if a time-switch or programmer has switched it off. And the cylinder 
thermostat will not always switch the boiler off, because the boiler sometimes needs to heat the 
radiators.
Cylinder thermostats are usually fitted between one quarter and one third of the way up the cylinder. 
The cylinder thermostat will have a temperature scale marked on it, and it should be set at between 
60C and 65C, then left to do its job. This temperature is high enough to kill off harmful bacteria in the 
water, but raising the temperature of the stored hot water any higher will result in wasted energy and 
increase the risk of scalding.
Location
ST9120C
CS92A
(typically next to hot water cylinder, in bedroom)
This section is to be completed by the Installer 
						

							27Keep this document in a Home Information Pack
This product and its associated documentation and packaging are protected by various intellectual 
property rights belonging to Honeywell Inc. and its subsidiaries and existing under the laws of the UK 
and other countries. These intellectual and property rights may include patent applications, registered 
designs, unregistered designs, registered trade marks, unregistered trade marks and copyrights.
Honeywell reserves the right to modify this document, product and functionality without notice. This 
document replaces any previously issued instructions and is only applicable to the product(s) described.
This product has been designed for applications as described within this docume\
nt. For use outside of 
the scope as described herein, refer to Honeywell for guidance. Honeywell cannot be held responsible 
for misapplication of the product(s) described within this document.
Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell 
Technologies Sàrl, ACS-ECC EMEA, Z.A. La Pièce 16, 1180 Rolle, Swit\
zerland by its Authorised 
Representative Honeywell Inc.
CONFIGURATION & SERVICE DATACS92A CONTROLS LAYOUT
Boiler & System Service Log
The space below can be used to provide a record of boiler & system services and 
the names and contact numbers of the Installer and Service Personnel.
This information is important for a Home Information Pack.
Service/Installation 
DateInstallation/Service 
Engineer Telephone Number / 
Contact Details
ST9120C CONTROLS LAYOUT
Sensor element
Transceiver
Green light 
(under button)
Button
Red light 
(under button) 
						

							3
Contents
CONTROL OF YOUR SYSTEM
 General Description of Controls in Your System ............................................... 4
  The way to use a Timer  ........................................................................\
............. 4
  Your Cylinder Thermostat  ........................................................................\
......... 5
GETTING STARTED WITH YOUR ST9120C
  Step 1: Setting the Date & Time  ....................................................................... 6
  Step 2: Running a Built-in Programme ............................................................. 7
PROGRAMMING YOUR  ST9120C
  The Built-in Programmes / Your Personal Programme ......................................8
  Reviewing the Programme Times  ..................................................................... 9
  Modifying the Programme  ........................................................................\
........ 9
  Disabling / Enabling Time Periods ................................................................. 11
OPERATING YOUR  ST9120C
  Choosing the Operating Mode  ....................................................................... 12
  Overriding the Operation Without Changing the Programmes .......................12
  The Extra Hour Function  ........................................................................\
......... 13
  The Holiday Function  ........................................................................\
.............. 13
  Enquiry Mode  ........................................................................\
......................... 14
FINE TUNING YOUR  ST9120C
  Changing from AM/PM Time Display to the 24 Hour Clock ............................15
  Changing the Installer Parameters  ................................................................. 15
BOILER SERVICE REMINDER
  Countdown to Service / When Service is Due  ................................................18
 Shut-down  ........................................................................\
............................... 19
OPERATING YOUR CS92A HOT WATER THERMOSTAT
  Basic Operation  ........................................................................\
...................... 19
  Battery Replacement  ........................................................................\
.............. 19
  Error Indications  ........................................................................\
..................... 20
FAQ  AND TROUBLESHOOTING
  Frequently Asked Questions  ........................................................................\
.. 21
  Troubleshooting Guide  ........................................................................\
........... 23
CONFIGURATION & SERVICE DATA (to be completed by Installer) ................. 26 
						

							4
General Description of Controls in Your System
Your Honeywell ST9120C provides timing control for your hot water system, letting 
you set ON and OFF periods to suit your own lifestyle. 
The ST9120C does not directly control the temperature but works together with a 
CS92A wireless cylinder thermostat.
With 7-day programming and up to 3 on/off periods per day, every day can be set 
differently.
ST9120C also has a Boiler Service reminder / Shut-down feature, which helps 
ensure your gas boiler is regularly serviced in compliance with UK Gas Safety 
Regulations. For more details see pages 18 & 19.
Your system includes a CS92A wireless cylinder thermostat and may include 
other Honeywell wireless controls. These products use state of the art 2 way RF 
communications to share information and give you robust and flexible control of your 
indoor environment.
The following instructions explain how to programme and use the ST9120C, and 
associated controls, to provide the most home comfort at the least cost.
The way to use a Timer
Think about the time periods when you are typically in the house and when you are not. 
These are the times you should use as the basis for the programmes. It will be necessary 
to allow some heat up time for the heating system after periods when it \
has been off – this 
would typically be 1 - 1½ hours, depending on your house and your preferences.
Other features are commonly available on the Timer to enhance comfort and 
convenience, for example, OVERRIDE, EXTRA HOUR, and MODE buttons.
A typical use of the OVERRIDE feature is when you return home unexpectedly for 
the rest of the day and the hot water is off. Just press the OVERRIDE button and 
the hot water will come on until the next programme time, at which point it will follow 
the normal programme. The advantage here is that you do not have to remember to 
switch off because the normal time programme does this for you. 
CONTROL OF YOUR SYSTEM 
						

							5
A typical use of the EXTRA HOUR button would be if you returned to the house for 
a short period when the hot water was off. Pressing the EXTRA HOUR button gives 
you 1, 2, or 3 hours of hot water, exactly when you need it. Another typical use is 
when the hot water is already on and you want it to stay on a little longer - just press 
EXTRA HOUR and, for that day only, an hour will be added to the end of the time at 
which hot water normally goes off.
The MODE button allows you to select how you want to operate your hot water. A 
typical use of this feature would be if you take a mid-week day off work, you can 
then set the MODE to ONCE to keep the system ON during the day from the first 
programmed ON time till the last programmed OFF time.
Your  Cylinder Thermostat
Your CS92A wireless cylinder thermostat measures the water temperature and signals 
this to the ST9120C timer. The timer then performs all the necessary control actions to 
maintain the water temperature at the set value. The set temperature is programmed by 
your Installer in the ST9120C Installer Mode, and you should never need \
to change this.  
A value of 60°C is typical. 
CONTROL OF YOUR SYSTEM (CONT .) 
						

							6
Your ST9120C should have been set up to work correctly when it was installed. 
However, the following will show you how you can modify your settings to meet 
your particular lifestyle.
To assist you with programming and everyday use your ST9120C will display text 
messages at every stage to help you get the most out of your central heating system. 
The ST9120C uses LoT™ Technology to constantly update the display to give you 
feedback about what is required.
Step 1: Setting the Date & Time
Your ST9120C had the date and time set at the factory, and these are normally 
maintained by a backup battery in the event of power failures. If you wish to change 
the date or time, or if the LoT™ Display shows the message ‘SET DA\
TE + TIME’ just 
follow the instructions below. Otherwise, go to Step 2.
a. Move the slider to the DAY/TIME position. The message ‘SET DATE + TIME’ will 
show briefly on the screen, followed by ‘SET THE DAY’, and the day of the month 
will now be flashing to indicate it can be changed.
GETTING STARTED WITH YOUR ST9120C
DAY/TIME
PROGRAMME RUN 
						

							7
GETTING STARTED WITH YOUR ST9120C
b. To change the day of the month, press the   or  buttons until the correct 
day is shown.  Each press of the button will change the date by one day. As soon 
as a change has been made, the message ‘IS DAY OK?’ will be displayed. Once 
the correct day is reached, press the green 
 button to confirm, and move to 
the next step. If you do not need to make a change, just press the  button 
immediately and this will move you to the next step.
c.  The month digits will now be flashing and ‘SET THE MONTH’ will be displayed. To 
change the month, press the 
  or  buttons until the correct month is shown. 
The message ‘IS MONTH OK?’ will be displayed. Press the green  button to 
confirm the month is correct and move to the next step.
d.  The year digits will now be flashing and ‘SET THE YEAR’ will be displayed. To 
change the year, press the 
  or  buttons until the correct year is shown. The 
message ‘IS YEAR OK?’ will be displayed. Press the green  button to confirm 
the year is correct. If you have made a change and the date is a valid date, the 
message ‘DATE SAVED’ will show and you can move to the next step. If the date 
you set was not valid, for example 31 September, the message ‘INVALID’ will 
show and you will be returned to the start of the date setting operation.
e.  The time will now be flashing and the message ‘SET THE TIME’ will be displayed. 
To change the time, press the 
  or  buttons until the correct time is shown. 
Each press of the button will change the time by one minute. Holding the button\
 
down for more than a few seconds will change the time slowly at first, then 
quickly. The message ‘IS TIME OK?’ will be displayed. Press the green 
 button 
to confirm the time is correct.  If you have made a change, the message ‘TIME 
SAVED’ will show, followed quickly by ‘DATE + TIME COMPLETE’.
f.   Move the slider to the RUN  position to complete setting the date and time.
Note: if the slider is moved at any time before the date and time have been set 
correctly, the message ‘DATE UNCHANGED’ will be displayed briefly, and your 
changes will not be saved.
Step 2: Running a Built-in Programme
With the date and time correct, your ST9120C Timer will now be operating to the 
built-in programmes. These have been designed to provide hot water at typical times 
throughout the day, but if you want to customise the settings, please see the next 
section ‘PROGRAMMING YOUR  ST9120C’ (page 8). 
						

							8
PROGRAMMING YOUR  ST9120C
The Built-in Programmes
The built-in programmes give you a starting point that you can personalise to your 
own requirements. Your Installer should have selected one and ticked the box 
alongside it. If there is no tick, the product normally leaves the factory with Profile A 
installed, but it is a simple matter to select one of the other profiles (see Changing 
the Installer Parameters, page 15).
 Built-in Programme (Profile A)ON 1OFF 1 ON 2OFF 2 ON 3OFF 3
Monday to Friday 6:30am8:30am12:00pm 1:00pm4:30pm10:30pm
Saturday & Sunday 6:30am9:30am12:00pm 1:00pm4:30pm11:00pm
ON 1OFF 1 ON 2OFF 2 ON 3OFF 3
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
Your Personal Programme
The table below has been left blank for you to record your own personal programme.
 Built-in Programme (Profile b) ON 1OFF 1 ON 2OFF 2 ON 3OFF 3
Monday to Friday 6:30am9:30am12:00pm 1:00pm4:30pm11:00pm
Saturday & Sunday 6:30am9:30am12:00pm 1:00pm4:30pm11:00pm
 Built-in Programme (Profile C)
ON 1OFF 1 ON 2OFF 2 ON 3OFF 3
Monday to Friday 6:30am7:30am12:00pm 12:00pm 5:00pm10:00pm
Saturday & Sunday 8:30am9:30am12:00pm 1:00pm5:30pm10:30pm 
						

							9
PROGRAMMING YOUR  ST9120C
Reviewing the Programme Times
To review your programme, move the slider to the PROGRAMME position. 
To review the programme times, press the 
 button repeatedly. The appropriate 
ON and OFF markers will be displayed to show you which time is being reviewed. 
Any of these times can be adjusted by using the 
  or  buttons, and then 
confirmed using the  button. Remember to return the slider to the RUN  position 
after reviewing is complete.
Modifying the Programme
The programme has three pairs of ON/OFF switching times per day. Each time can 
be set between 3.00 am and 2.50 am (on the next day) to allow you to p\
rogramme to 
stay on past midnight, if required. 
a.  Move the slider to the PROGRAMME position. ‘SET PROGRAMME’ will show 
briefly to verify this action.
b.  ‘SET ON-TIME 1’ will then be displayed and the time setting for th\
e first ON 1 
time for MONDAY will now be flashing to indicate it can be changed. If you do 
not wish to change the time, press the green 
 button and move to the next 
step. If you do wish to make a change, use the   or  buttons to change 
the first ON 1 time. Each press of the button will change the time by 10 minutes. 
As soon as the time has been changed, the message ‘ON-TIME 1 OK?’ \
will be 
displayed. Press the green 
 button to confirm the time is correct and move to 
the next step. ‘SAVED’ will be displayed for a moment to confirm that any change 
has been saved to memory.
DAY/TIME
PROGRAMME RUN 
						

							10
Note: When pressing the  button the next ON or OFF marker may start to flash. 
This indicates you have tried to set a time equal to one of the next programme times 
already in the memory.  Similarly, when pressing the 
 button the previous ON or 
OFF marker may start to flash. This indicates you have tried to set a time equal to 
one of the previous programme times. If this happens the ST9120C simply moves 
both times together as long as you continue to press the 
  or  buttons.  Follow 
the procedure in ‘Reviewing the Programme Times’ (page 9) to check and adjust 
these times as necessary.
c. 
‘SET OFF-TIME 1’ will be displayed and the first OFF 1 time will now be flashing. If 
you do not wish to change the time, press the green  button and move to the next 
step. Otherwise, use the   or  buttons to change the time. Press the green  button to confirm the time is correct and move to the next step. ‘SAVED’ will be 
displayed for a moment to confirm that any change has been saved to memory.
d.  The remaining ON and OFF times (ON 2, OFF 2, ON 3, OFF 3) can be set by 
using the   or  buttons to change the time, then the green  button 
to confirm the time is correct and move to the next step. If you do not wish to 
change the time, just press the green 
 button to move directly to the next ON/
OFF time without making any changes.
e.  After setting or reviewing the last off time, OFF 3, the message ‘COMPLETE’ will 
be displayed to indicate the times for Monday have been set.
You now have a choice of how to set the programme for the next day:
Copying One Day’s Programme to Another Day (example Monday to Tuesday):
f.   Whilst the day is showing Monday, Press the COPY DAY button. The message 
‘COPY MON TO TUESDAY OK?’ will be displayed and the letters TUE will flash 
to indicate the programme for Monday can be copied to Tuesday.
g.  To select a different day to copy to, press the NEXT DAY button to cycle through 
the days. With each press of the NEXT DAY button the message will change to 
indicate the new day you are copying to.
h.  When the required day is indicated, press the green 
 button to confirm, and 
the message ‘MON COPIED’ will be displayed for a moment. The day i\
nto which 
Mondays programme has been copied is now available to have its programme 
edited.
Note:  Once a day’s programme has been confirmed in this way, it now becomes the 
day whose programme is copied if the COPY DAY button is pressed again.
OR
Programming a Different Day:
i.  Press the NEXT DAY button to select the next day, which is displayed along the 
top of the screen.  The programme for that day can then be adjusted by following 
steps  b – e above.  Programmes for the remaining days can be set in the same 
way, using the NEXT DAY button to move to the next day.
PROGRAMMING YOUR  ST9120C