Honeywell Lynxr 2 Instruction Manual

							– 11 – 
SYSTEM OVERVIEW
SYSTEM OVERVIEWSYSTEM OVERVIEW SYSTEM OVERVIEW 
    
About the Master Keypad 
 
General  
IMPORTANT: If the keypad beeps rapidly upon entering the premises, an alarm has occurred during 
your absence and an intruder may still be on the premises. LEAVE IMMEDIATELY and CONTACT 
THE POLICE from a nearby safe location.  
 
The keypad allows you to control all system functions. In the speaker phone mode the keypad becomes 
a full-function telephone keypad. The keypad features telephone-style keys and a Liquid Crystal 
Display (LCD), which shows the nature and location of all occurrences.  
 
09015-001-V0 
 
The keypad also features a built-in sounder, which will sound during alarms and troubles. The keypad 
also beeps during certain system functions, such as during entry/exit delay times, in Chime mode, 
and when depressing any of the keys (to acknowledge the key press). In addition, a built-in speaker 
announces system status. 
The voice announcement volume is adjustable, however the “beeps” that sound in response to alarms 
always sound at the maximum volume level. All other “beeps” (trouble, chime, exit/entry, etc) can be set 
to either low or high volume. 
  
						

							– 12 – 
SYSTEM OVERVIEW
SYSTEM OVERVIEWSYSTEM OVERVIEW SYSTEM OVERVIEW 
    
Master Keypad Definitions   
BYPASS
NO DELAY RECORD
TEST
FUNCTION STATUSVOLUMEPLAY
CODE LIGHTS ON
LIGHTS OFF
CHIME ESCAPE
ADD
DELETE
SELECT
ARMED
READY
132
4
6
8
9
101215
16
17
19
18
1409015-003-V0
3
65
5
98
7
AUX0
13
74STAY
OFF
AWAY1
2021
2
11 
 
 
IMPORTANT! 
When you use the keypad to enter codes and commands, press the keys within 2 seconds of one another. If 2 
seconds elapse without a key depression, the entry is aborted and must be repeated from its beginning. 
NOTE: Different timeouts may occur when defining auxiliary functions and setting the real-time clock. 
Note: The system functions described below are for reference only and require additional key entries to activate. 
1. DISPLAY WINDOW: Liquid Crystal Display 
(LCD).  Displays protection point identification 
and system status, messages, and user 
instructions.  
2. ARMED INDICATOR:  (RED) Lit when the 
system has been armed  (STAY, AWAY, NO 
DELAY). Blinks when armed and fault exists, or 
once per second when AVM (VOX or Talk) or 
speaker phone mode is active. 3. READY INDICATOR: When lit, indicates 
system is ready to be armed; blinking indicates 
system is not ready (a zone is open). Blinks once 
per second when AVM (VOX or Talk) or speaker 
phone mode is active. 
4. PLAY
  KEY: Announces a user’s message if 
one was previously recorded. See RECORD 
function. Used to adjust volume of voice 
messages. 
						

							– 13 – 
SYSTEM OVERVIEW
SYSTEM OVERVIEWSYSTEM OVERVIEW SYSTEM OVERVIEW 
    
Master Keypad Definitions 
 
5. TEST
  KEY: Tests the system and alarm 
sounder.  
6. BYPASS
  KEY: Removes individual protection 
zones from being monitored by the system. 
Displays currently bypassed zones.  
Used to adjust volume of voice messages. 
7. CODE
  KEY:  Allows entry of additional user 
codes that can be given to other system users. 
8. CHIME
  KEY:  Turns the Chime mode on and 
off. When on, any entry through a protected 
delay or perimeter zone while the system is 
disarmed will cause a tone and voice descriptor 
to sound at the keypad. 
9. INTERNAL SOUNDER:  Source of alarm sounds 
(see Summary of Audible Notifications section). 
10. FUNCTION
  KEY: Allows alternate key 
functions. It is used as a “repeat” key during 
Clock/Calendar setting. 
11. NO DELAY
  KEY: Used with STAY or AWAY 
function to eliminate the entry delay. Alarm 
sounds immediately if entry is opened. 
12. STATUS
  KEY:  When pressed prior to arming, 
the keypad will display all open zones, and will 
announce system status. 
13. LIGHTS ON
  / LIGHTS OFF  KEYS:  Turns 
lights or other devices on or off, if programmed by 
the installer. 
14. AUX
  / SELECT   KEY:  Can be programmed 
to either perform a predefined function or to send 
a preset message to a pager or a “Follow Me” 
system phone number. 15. STAY
  / DELETE   KEY: Arms the perimeter 
burglary protection, guarding protected doors, 
windows and other perimeter protection points, 
and sounds an alarm if one is opened. Interior 
protection is not armed, which allows movement 
within your house without causing an alarm. 
Entrance can be made through an entry delay 
zone without causing an alarm if the system is 
disarmed before the entry delay time expires. 
Used to delete messages.  
16. AWAY
  /  ADD   KEY: Completely arms both 
perimeter and interior burglary protection for 
backup protection by sensing an intruders 
movements through protected interior areas as 
well as guarding protected doors, windows, etc. 
Entrance can be made through an entry delay 
zone without causing an alarm if the system is 
disarmed before the entry delay time expires. 
Used to accept “Follow Me”  phone number and 
Clock/ Calendar mode entries. 
17. OFF
  / ESCAPE  KEY:  Disarms the burglary 
portion of the system, silences alarms and 
audible trouble indicators, and clears alarm 
trouble display after the problem has been 
corrected.  Used to exit/abort “Follow Me” phone 
number and Clock/Calendar mode. 
18. MICROPHONE: Used to record personal 
messages up to 85 seconds long, and for 2 way 
voice and speaker phone. 
19. SPEAKER: Source of audible internal warning 
and confirmation sounds, status announcements, 
as well as alarms (see Summary of Audible 
Notifications). 
20. RECORD: Activates the recording function to 
record personal messages. 
21. VOLUME: Sets the volume of system 
announcements and status beeps. 
–– KEYS 0-9:  Used to enter your individual 
security access code(s).  
						

							– 14 – 
SYSTEM OVERVIEW
SYSTEM OVERVIEWSYSTEM OVERVIEW SYSTEM OVERVIEW 
    
About the Display and Indicators 
 
Display Definitions (for other displays, see Trouble Messages) ALARM
AWAYINSTANTSTAYFIREREC MESSAGEBYPASSFAULT
CHIME   TEST  LOW BAT  AC
 ALARM:   Appears when the system is armed and an intrusion has been detected (also appears 
during a fire alarm or audible emergency alarm). Accompanied by the protection zone 
that is in alarm. 
AWAY:  All burglary zones, interior and perimeter, are armed.  
INSTANT:  Entry delay is turned off. 
STAY:  Perimeter burglary zones, such as protected windows and doors, are armed. 
UL
ULUL UL 
    LYNXR-2 Series is not intended for UL985 Household Fire applications unless a 24-hour backup 
battery (P/N LYNXRCHKIT-HC) is installed. 
FIRE:   Appears when a fire alarm or fire fault is present. Accompanied by a display of the 
zone that is in alarm. 
LOW BAT:   Low battery condition in a wireless sensor (if zone number is displayed) or low system 
battery (if no zone number is displayed). If 00 is displayed, a wireless keypad (5827) 
has a low battery condition. 
AC:  Appears when AC power is present. If not displayed, the system is operating on 
backup battery power. 
CHIME:   Appears when the Chime feature is activated. 
TEST:  Appears when the system is in Test mode.  
 LYNXR-2SIA blinks during the last 5 minutes of test.  
REC:  Appears when the system is in Recording mode. 
MESSAGE:  Appears when a message has been recorded and has not yet been played back. 
BYPASS:  Appears when one or more burglary protection zones have been bypassed. 
FAULT:   Appears at any time a malfunction is discovered in the system; or any time an open 
is detected in a fire zone; or when a fault in a day/night burglary zone is discovered 
during a disarmed period. Accompanied by a display of the zone number in trouble. 
PH:  Appears in place of the clock when the speaker phone mode is active. 
PC:  Appears during a remote phone control session. 
LED Meanings 
ARMED LED:  ON = System armed 
(Red)  OFF = System disarmed 
  Blinking = System armed, but a fault exists 
  Blinking alternately with READY LED = AVM (VOX or Talk) or speaker phone mode 
is active 
READY LED:  ON = System disarmed, ready to arm 
(Green)  OFF = System armed 
  Blinking = System disarmed, not ready to arm (a fault exists) 
  Blinking alternately with ARMED LED = AVM (VOX or Talk) or speaker phone 
mode is active.  
						

							– 15 – 
SECURING THE PREMISES
SECURING THE PREMISESSECURING THE PREMISES SECURING THE PREMISES 
    
Checking System Status 
General Information 
Before arming your system, all protected doors, windows, and other protection zones must be closed or 
bypassed (see the BYPASSING PROTECTION section). Pressing the 
STATUS key will announce all 
zones that are faulted, as well as any other abnormal system condition, making it easier for you to 
secure any open zones. 
READY LIGHT:  The green READY indicator on the keypad will be lit if the system is ready to be 
armed.  If blinking, the system is not ready.  
Press the STATUS Key 
Press the STATUS key once to announce the general status of the system.  
Depending on the current state of the system the following phrases may be heard: 
disarmed, ready to arm [message] [check system] 
disarmed, [not ready to arm], [message] 
armed [away] [stay] [instant] [check system] [message] 
 
NOTE:   The phrases shown in brackets are variable, and are announced only if appropriate in the current state of the 
system. 
 
Press the STATUS key a second time† to announce specific system status.  
Depending on the current state of the system the following phrases may be heard: 
fire alarm [zone voice descriptors] 
carbon monoxide alarm [zone voice descriptors] 
alarm [zone voice descriptors] 
fire fault [zone voice descriptors] 
carbon monoxide fault [zone voice descriptors] 
fault [zone voice descriptors] 
low battery  [zone voice descriptor] 
system low battery 
check system 
AC loss 
zones bypassed 
chime  
†
  (second depression must be made within 10 seconds of the first)  
VOLUME LEVEL: The volume level of system announcements can be increased or decreased.  Refer to 
the MESSAGE RECORDING/PLAYBACK section for the procedure. 
 
System Can Be Armed 
The READY LED will be lit once all protection zones have been closed or bypassed. You may now arm 
the system as usual.  
						

							– 16 – 
SECURING THE PREMISES
SECURING THE PREMISESSECURING THE PREMISES SECURING THE PREMISES 
    
Arming the System  
Arming in Stay Mode 
Use this mode when you are staying home, but expect someone to use the entrance door later.  Close all 
protected perimeter windows and doors before arming.  The green READY indicator on the keypad 
should be lit if the system is ready to be armed. 
To arm in STAY mode: 
                       + STAY  or press and hold 
STAY **
 
  Your User code** 
** See Quick Arming paragraph.  The keypad beeps three times and displays the armed STAY message. The red ARMED indicator lights 
and the system announces “armed STAY–exit now.”   
 When armed in STAY mode, the system will sound an alarm if a protected door or window is opened, 
but you may otherwise move freely throughout the premises. Late arrivals can enter through the 
entrance door without causing an alarm, but they must disarm the system within the entry delay 
period or an alarm will occur.  
 Restarting Exit Delay While System Armed 
Ask your installer if this feature is active for your system. If active, you can restart the exit delay at 
any time after arming in STAY mode by entering the User Code and pressing the 
STAY  key, or simply 
by pressing the 
STAY  key by itself. This avoids having the user disarm then re-arm the system after 
allowing someone to enter or exit. 
 
Exit Delay Restart/Reset 
 On the LYNXR-2SIA, this option also enables automatic exit delay reset, which resets exit delay if the 
entry/exit door is re-opened and closed before exit delay time expires after arming. Automatic Exit 
Delay Reset occurs only once during an armed period.  
To restart exit delay while system is armed in STAY mode: Press STAY key.
 
Arming In Away Mode 
Use this mode when no one will be staying on the premises. Close all protected perimeter windows and 
doors before arming. The green READY indicator on the keypad should be lit if the system is ready to 
be armed. 
To arm in AWAY mode: 
                        +  AWAY  or press and hold 
AWAY **
 
  Your User Code ** 
** See Quick Arming paragraph. 
 
The keypad beeps twice, or beeps continuously if exit warning has been programmed for your system, 
and displays the armed AWAY message. The red ARMED indicator lights and the system announces 
“armed AWAY–exit now.”   
 When armed in AWAY mode, the system will sound an alarm if a protected door or window is opened, 
or if any movement is detected inside the premises. You may leave through the entrance door during 
the exit delay period without causing an alarm. You may also re-enter through the entrance door, but 
you must disarm the system within the entry delay period or an alarm will occur.   
						

							– 17 – 
SECURING THE PREMISES
SECURING THE PREMISESSECURING THE PREMISES SECURING THE PREMISES 
    
Arming the System  
Auto Stay Feature 
If this feature is enabled by installer, the LYNXR-2SIA, when armed AWAY from the control’s keypad 
or a Wireless Keypad, switches to the STAY mode if the Exit Time expires and no exit has been made.   NOTE:   If the exit route entry/exit sensor is in a check condition or has been bypassed it will result in a loss of interior protection because the alarm system will arm STAY in this case. Consult with your installer for servicing of the entry exit zones or to turn off this feature if a check condition on entry exit zones occurs.  
Arming the System with No Delay 
Use NO DELAY with STAY mode when you are staying home and do not expect anyone to use the 
entrance door. 
 Use NO DELAY with AWAY mode when the premises will be vacant for extended periods of time such 
as vacations, etc.  
 When armed with NO DELAY, the system will sound an alarm if a protected door or window is opened, 
including the entrance door. You may leave through the entrance door during the exit delay period 
without causing an alarm, but an alarm will sound as soon as someone reenters. 
 
To arm with NO DELAY:  
                         +  AWAY or 
STAY  +  
NO DELAY  
  Your user code** 
** See Quick Arming paragraph.  
Quick Arming 
If Quick Arm was programmed by the installer, you do not need to enter the security code to arm the 
system.  Instead, simply press and hold down the desired arming key for at least 2 seconds.  The 
security code must always be used to disarm the system, however. 
 
To arm if Quick Arm is active:  AWAY or 
STAY  hold down for at least 2 seconds 
 
To arm with NO DELAY if Quick Arm is active:  
AWAY or 
STAY  then 
NO DELAY hold down for at 
least 2 seconds 
 
IMPORTANT: The Babysitter Code and Installer Code cannot disarm the system unless it was used to 
arm the system. In addition, if the system is armed by pressing and holding the Quick-Arm buttons, 
neither the Babysitter Code nor Installer Code can disarm the system.  
						

							– 18 – 
SECURING THE PREMISES
SECURING THE PREMISESSECURING THE PREMISES SECURING THE PREMISES 
    
Entry/Exit Delays  
Exit Delay 
Exit delay begins immediately after arming the system, and gives you time to leave through the 
designated exit door without setting off an alarm.  A slow beeping will sound throughout the exit delay 
period, if programmed. During the last 10 seconds of the exit delay fast beeps will sound as a warning 
that the delay time is nearing its end. The exit beeps cannot be silenced. 
Exit Alarms Exit Alarm Active   
To minimize false alarms sent to the alarm monitoring company, your system may have been 
programmed for this feature. Ask your installer if Exit Alarm is active for your system.      
Whenever you arm the system, the exit delay begins. If an entry/exit door or interior zone is faulted 
when the exit delay ends (e.g., exit door left open), the system sounds an alarm and starts the entry 
delay timer. If you disarm the system before the entry delay ends, the alarm sound stops and the 
message CA is displayed on the keypad, along with a zone number indicating the faulted zone. No 
message is sent to the alarm monitoring company. To clear the exit alarm condition, the open zone 
must be made re-secured; to clear the display, enter your security code and press the 
OFF key. 
If you do not disarm the system before the entry delay ends, and an entry/exit door or interior zone is 
still open, the alarm sound continues and an exit alarm message is sent to the alarm monitoring 
company. The message EA is displayed on the keypad, along with a zone number indicating the 
faulted zone. The alarm will continue to sound until the system is disarmed or timeout ocurs. To stop 
the alarm, the system must be disarmed by entering your security code and pressing the 
OFF key; and 
the message CA is displayed on the keypad, indicating that the alarm has been cancelled (if this 
feature is enabled by the installer).  To clear the display, enter your security code and press the 
OFF 
key a second time.  An exit alarm also results if an entry/exit door or interior zone is faulted within two 
minutes after the end of the exit delay. 
 
Entry Delay 
Entry Delays give you time to disarm the system when you re-enter through the designated entrance 
door. You must disarm the system before the entry delay period ends, or an alarm will occur. The 
keypad beeps during the entry delay period, reminding you to disarm the system. There are two entry 
delays (if programmed). The first is for your primary entrance and the second can be used for a 
secondary entrance, where a longer delay is required to walk to the keypad to disarm the system. You 
can also arm the system with no entry delay at all by using the 
NO DELAY key when arming. This can 
provide greater security while on the premises or while away for extended periods of time. See 
ARMING THE SYSTEM section for procedure. See your installer for delay times programmed for your 
system. 
Exit Delay:       
         00-99 seconds 
Entry Delay 1: 
         00-99 seconds  Entry Delay 2:            00-99 seconds 
LYNXR-2SIA Exit/Entry Delay Times 
Exit Delay:                45-96, 120 seconds 
Entry Delay 1:          30-96, 120, 180, 240 seconds  Entry Delay 2:            30-96, 120, 180, 240 seconds  
						

							– 19 – 
SECURING THE PREMISES
SECURING THE PREMISESSECURING THE PREMISES SECURING THE PREMISES 
    
Disarming the System 
 
NOTE:  The control will provide a long confirmation ding when it is disarmed using an RF Key Fob.  
Use the 
OFF key to disarm the system and to silence alarm and trouble sounds. See the SUMMARY 
OF AUDIBLE NOTIFICATION section for information, which will help you to distinguish between fire 
and burglary alarm sounds. 
 
**IMPORTANT** 
If you return and the main burglary sounder is on, DO NOT enter the premises, but call the police 
from a nearby safe location. If you return after an alarm has occurred and the main sounder has shut 
itself off, the keypad will beep rapidly upon entering. This indicates that an alarm has occurred 
during your absence and an intruder may still be on the premises. LEAVE IMMEDIATELY and 
CONTACT THE POLICE from a nearby safe location.   
To disarm the system and silence burglary alarms:                        +  OFF 
  Your user code
 
During Entry Delay or when an Alarm Condition exists, the system will be disarmed as soon as the 
correct user code is entered on the keypad. Entering the OFF key is not required. The entry beeps or 
alarm sound can be silenced by pressing any key however, it will restart in 10 seconds if the correct 
User Code is not entered. 
The READY indicator will light (if no alarms have occurred while armed) and the keypad will beep once 
to confirm that the system is disarmed. 
Memory of Alarm 
If an alarm occurs, the keypad displays the zone number (s) that caused the alarm and the type of 
alarm (e.g., “FIRE ALARM”). These messages remain displayed until cleared by a user.  
 
To clear the display, note the zone number displayed and enter an OFF sequence (enter your security 
code and press the 
OFF key).  
 
If the READY indicator is blinking, go to the displayed zone and correct the fault (close windows, etc.). 
If the fault cannot be corrected, notify your alarm company. 
   
						

							– 20 – 
SECURING THE PREMISES
SECURING THE PREMISESSECURING THE PREMISES SECURING THE PREMISES 
    
Bypassing Protection Zones 
 
Bypassing Individual Zones 
Use the BYPASS key when you want to arm your system with one or more zones intentionally 
unprotected. Bypassed zones are unprotected and will not cause an alarm when violated while your 
system is armed. All bypasses are removed when an OFF sequence (security code plus OFF) is 
performed. Bypasses are also removed if the arming procedure that follows the bypass command is 
not successful. 
The system will not allow fire zones to be bypassed. 
 
The system must be disarmed first. 
To bypass a zone(s): 
                        +  BYPASS + 2-digit zone number(s) 
for zone(s) to be  
  Your user code  bypassed (e.g., 02, 03, etc.)
 
 
Important! All single-digit numbers must be preceded by a zero (for example, enter 02 for zone 2). 
 
The keypad will provide a confirmation beep and display the word “BYPASS” along with each bypassed 
zone number. Wait for these zones to be displayed, to be sure that intended zones are bypassed. 
 
Arm the system as usual when the keypad displays the READY LED on steady. 
 
Forced Bypass 
Your system may allow you to easily bypass all open (faulted) zones without having to enter zone 
numbers individually. Ask your installer if this feature is active.
 
To bypass a zone(s): 
                        +  BYPASS + 
FUNCTION 
  Your user code   
In a few moments, all open zones will be displayed along with the word “BYPASS.” Wait for these zones 
to be displayed before arming. Arming the system before zones are displayed eliminates all bypasses. 
 
Arm the system as usual when the keypad displays the READY LED on steady. 
 
Displaying Bypassed Zones 
The system allows you to determine what zones have been previously bypassed. Bypassed zones can be 
displayed only when the system is disarmed, and when the “BYPASS” message described above is 
displayed. 
To display bypassed zone(s): 
                         +  BYPASS + WAIT
 
  Your user code 
 
In a few moments, all open zones will be sequentially displayed along with the word “BYPASS.”