Home > Honeywell > Control panel > Honeywell control panel VISTA40 Security System User Manual

Honeywell control panel VISTA40 Security System User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Honeywell control panel VISTA40 Security System User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 178 Honeywell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							 
     
    – 21 – 
    Accessing Other Partitions (cont’d) 
    ARM  P 1 2 3 4 5 6 7 8 
    HIT  0-8  X X X -  -  X -  - 
    The prompt displays all the partitions. The user 
    may only arm/disarm the partitions they are 
    assigned access to.  
    To select the partition(s) that are to be armed, 
    enter the desired number 1-8. An X will appear 
    under that partition. Entering a partition’s 
    number again will delete the “X” and that 
    partition will not arm when this prompt is exited.   
    Pressing 0 will turn all partitions the user is 
    assigned access to on/off. 
    When completed, press ✳ to exit. All the partitions 
    with the “X” will then arm/disarm. 
    Global Arming Notes: 
    • When performing a Global Arm, if there are faults in either partition, the 
    system will enter a Summary Mode. Faulted zones in all the partitions 
    will be displayed. These faults must be corrected or bypassed. This 
    Summary Mode will end in approximately 120 seconds if no keys are 
    pressed. 
    • When performing a Global Disarm, if either of the partitions has a 
    condition which would cause the keypad to beep (e.g., alarm memory or a 
    trouble condition), the system enters a Summary Mode and displays the 
    condition. This Summary Mode will end in approximately 120 seconds if 
    no keys are pressed. 
     
     
     
     
     
     
     
     
     
     
      
    						
    							 
     
    – 22 – 
    Checking For Open Zones 
    Using the ✳  READY Key 
    Before arming your system, all protected doors, windows and other protection 
    zones must be closed or bypassed (see BYPASSING section).  Otherwise the 
    keypad will display a Not Ready message. Using the READY key will 
    display all zones that are faulted, making it easier for you to secure any open 
    zones. 
    To show faulted zones: 
     DISARMED - PRESS 
     TO SHOW FAULTS 
    Note: Some keypads light a green LED when 
    the system is ready. If not lit, the system is not 
    ready to be armed. 
      READY 
    1.  Do not enter security code, but simply press  ✳  . 
    FAULT   05  FRONT 
    UPSTAIRS BEDROOM Typical fault display 
     
    2. DISARMED 
    READY TO ARM 
     
    Secure or bypass the zones displayed before 
    arming the system. The Ready message will 
    be displayed†
     when all protection zones have 
    been either closed or bypassed. 
    †
     NOTE: All or part of this message may be 
    replaced by a customized message programmed 
    by the installer.  Bear this in mind whenever 
    the instructions indicate that the 
    DISARMED or READY message will be 
    displayed. 
     
     
     
     
     
     
     
     
      
    						
    							 
     
    – 23 – 
    Displaying All Zone Descriptors 
    Using the ✳  READY Key 
    The Alpha Keypads can also display all the zone descriptors that are 
    programmed in your system. The abbreviated instructions for the READY 
    key will appear first, followed by the zone descriptors. Displaying all 
    descriptors is useful when you need to know the zone number of a particular 
    zone, as when bypassing zones. 
    The Disarmed-Ready to arm message must be displayed before zone 
    descriptors can be displayed. 
      READY 
     Press the   ✳  key and hold down for at least 5 seconds. 
     
      
    						
    							 
     
    – 24 – 
    Bypassing Protection Zones 
    Using the   6  BYPASS Key 
    This key is used when you want to arm your system with one or more zones 
    intentionally unprotected. Bypassed zones are unprotected and will not cause 
    an alarm when violated while your system is armed. All bypasses are 
    removed when an OFF sequence (security code plus OFF) is performed. 
    Bypasses are also removed if the arming procedure that follows the bypass 
    command is not successful. 
    Note: The system will not allow fire or emergency zones to be 
    bypassed. 
    To bypass zones, the system must be disarmed first. 
       BYPASS 
    1.  Enter your security code and press   6  . 
    2.  Enter zone number(s) for the zones to be bypassed (e.g., 01, 02, 03, etc.). 
     Important! All single-digit numbers must be preceded by “0” (for 
    example, enter 01 for zone 1). 
    3.  BYPASS  07 FRONT 
    UPSTAIRS BEDROOM 
    Typical bypass message 
    When finished, the keypad will display the 
    word BYPASS along with each bypassed zone 
    number. Wait for these zones to be displayed 
    before arming. Arming the system before 
    bypassed zones are displayed eliminates all 
    bypasses. 
    4.  DISARMED BYPASS 
    READY TO ARM 
    Arm the system as usual when the keypad 
    displays ready to arm message. 
     
     
      
    						
    							 
     
    – 25 – 
    Bypassing Protection Zones (cont’d) 
    Quick Bypass 
    Your system allows you to easily bypass all open (faulted) zones without 
    having to enter zone numbers individually.  
    Note: All bypasses are removed when an OFF sequence (security code plus 
    OFF) is performed. 
    To use the Quick Bypass feature: 
      BYPASS 
    1.  Enter your security code and press  6  then press  # . 
    2. BYPASS  07 FRONT 
    UPSTAIRS BEDROOM 
    Typical bypass message 
    In a few moments, all open zones will be 
    displayed along with the word BYPASS. Wait 
    for these zones to be displayed before arming. 
    Arming the system before bypassed zones are 
    displayed eliminates all bypasses. 
    3. DISARMED BYPASS 
    READY TO ARM 
    Arm the system as usual when the keypad 
    displays the ready to arm message. Bypassed 
    zones are unprotected and will not cause an 
    alarm when violated while your system is 
    armed. 
    Displaying Bypassed Zones 
    For determining what zones have been previously bypassed. Bypassed zones 
    can be displayed only when system is disarmed. 
      BYPASS 
    1.  Enter your security code and press  6  . 
    2.  Wait for all bypassed zones to be sequentially displayed. 
     
     
     
     
     
     
      
    						
    							 
     
    – 26 – 
    Arming Perimeter Only 
    (With Entry Delay ON) 
    Using the   3  STAY key 
    Use this key when you are staying home, but might expect someone to use 
    the entrance door later. 
    When armed in STAY mode, the system will sound an alarm if a protected 
    door or window is opened, but you may otherwise move freely throughout the 
    premises. Late arrivals can enter through the entrance door without causing 
    an alarm, but they must disarm the system within the entry delay period or 
    an alarm will occur.  
    Check with your installer for a list of the zones that are bypassed during the 
    STAY mode. 
    Close all perimeter windows and doors before arming (see 
    CHECKING FOR OPEN ZONES section) 
      STAY 
    1.  Enter your security code and press  3    
    2. ARMED ***STAY*** 
    ZONE BYPASSED 
    The keypad beeps three times, displays the 
    armed message. 
    Note: ZONE BYPASSED in this display 
    simply indicates that some zones of protection 
    are not armed when using STAY mode. 
     
     
     
     
     
     
     
     
     
     
     
      
    						
    							 
     
    – 27 – 
    Arming Perimeter Only 
    (With Entry Delay OFF) 
    Using the   7  INSTANT Key 
    Use this key when you are staying home and do not expect anyone to use the 
    entrance door. 
    When armed in INSTANT mode, the system will sound an alarm if a 
    protected door or window is opened, but you may otherwise move freely 
    throughout the premises. The alarm will also sound immediately if anyone 
    opens the entrance door. 
    Check with your installer for a list of the zones that are bypassed during the 
    INSTANT mode. 
    Close all perimeter windows and doors before arming (see 
    CHECKING FOR OPEN ZONES section) 
      INSTANT 
    1.  Enter your security code and press  7    
    2. ARMED INSTANT 
    ZONE BYPASSED 
    The keypad beeps three times, displays the 
    armed message.  
    Note: ZONE BYPASSED in this display 
    simply indicates that some zones of protection 
    are not armed when using INSTANT mode. 
     
     
     
     
     
     
     
     
     
      
    						
    							 
     
    – 28 – 
    Arming All Protection 
    (With Entry Delay ON) 
    Using the   2  AWAY Key 
    Use this key when no one will be staying on the premises. 
    When armed in AWAY mode, the system will sound an alarm if a protected 
    door or window is opened, or if any movement is detected inside the premises. 
    You may leave through the entrance door during the exit delay period 
    without causing an alarm. You may also reenter through the entrance door, 
    but must disarm the system within the entry delay period or an alarm will 
    occur. 
    Close all perimeter windows and doors before arming (see 
    CHECKING FOR OPEN ZONES section) 
      AWAY 
    1.  Enter your security code and press  2  . 
    2. ARMED **AWAY** 
    YOU MAY EXIT NOW 
    The keypad will beep twice and will display the 
    armed message.  
    Note: The YOU MAY EXIT NOW portion of 
    the message disappears when exit delay 
    expires. 
     
     
     
     
     
     
     
     
     
      
    						
    							 
     
    – 29 – 
    Arming All Protection 
    (With Entry Delay OFF) 
    Using the   4  MAXIMUM Key 
    Use this key when the premises will be vacant for extended periods of time 
    such as vacations, etc., or when no one will be moving through protected 
    interior areas. 
    When armed in MAXIMUM mode, the system will sound an alarm if a 
    protected door or window is opened, or if any movement is detected inside the 
    premises. You may leave through the entrance door during the exit delay 
    period without causing an alarm, but an alarm will be sounded as soon as 
    someone reenters. 
    Close all perimeter windows and doors before arming (see 
    CHECKING FOR OPEN ZONES section). 
      MAXIMUM 
    1.  Enter your security code and press  4  . 
    2. ARMED *MAXIMUM* 
    YOU MAY EXIT NOW 
    The keypad will beep twice and will display the 
    armed message.  
    Note: The YOU MAY EXIT NOW portion of 
    the message disappears when exit delay 
    expires. 
     
     
     
     
     
     
     
     
     
     
     
     
      
    						
    							 
     
    – 30 – 
    Disarming And Silencing Alarms 
    Using the   1  OFF Key 
    The OFF key is used to disarm the system and to silence alarm and trouble 
    sounds. See SUMMARY OF AUDIBLE NOTIFICATION section for 
    information which will help you to distinguish between FIRE and 
    BURGLARY alarm sounds. 
    IMPORTANT: If you return and the main burglary sounder is on, DO NOT enter 
    the premises, but call the police from a nearby safe location. If you return after an 
    alarm has occurred and the main sounder has shut itself off, the keypad will beep 
    rapidly upon entering, indicating that an alarm has occurred during your absence. 
    LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe 
    location.  
    To disarm the system and silence burglary or fire alarms: 
      OFF 
    1.  Enter your security code and press  1  . 
    DISARMED 
    READY TO ARM 
    2.  The Ready message will be displayed (if no alarms have occurred while 
    armed) and the keypad will beep once to confirm that the system is 
    disarmed. 
    Memory of Alarm 
    The keypad displays the zone number and type of alarm for any zone that 
    has an alarm condition. These messages will remain displayed until cleared 
    by a user. If an alarm has occurred, note the zone number displayed on the 
    keypad and repeat step 1 above to clear the Memory of Alarm and restore 
    the Ready message display. If the Ready message will not display, go to the 
    displayed zone and remedy the fault (close windows, etc.). If the fault cannot 
    be remedied, notify the alarm agency. 
    If the system was armed when the alarm occurred, repeat step 1 twice: once 
    to disarm the system, a second time to clear the display. 
     
      
    						
    All Honeywell manuals Comments (0)

    Related Manuals for Honeywell control panel VISTA40 Security System User Manual