Home > Honeywell > Control panel > Honeywell control panel VISTA128FBPVISTA250FBP User Manual

Honeywell control panel VISTA128FBPVISTA250FBP User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Honeywell control panel VISTA128FBPVISTA250FBP User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 178 Honeywell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							 
     
    – 41 – 
    Chime Mode 
    Using the   9  Key 
    Your system can be set to alert you to the opening of a door or window while 
    it is disarmed by using CHIME mode. When activated, three tones will sound 
    at the Keypad whenever a protected perimeter door or window is opened, and 
    the Not Ready message will be displayed. Pressing the READY key will 
    display the open protection points. 
    Note that Chime mode can be activated only when the system is disarmed. 
    1. To turn Chime Mode on, enter the security code and press  9 
     . 
    CHIME MODE ON 
     
     The CHIME MODE ON message will appear 
    for about 2 seconds then disappear. To display 
    this message again (to determine whether 
    chime mode is on or off), simply press and hold 
    down the CHIME key for 5 seconds.  
    2. To turn Chime Mode off, enter the security code and press   9 
     again. 
    CHIME MODE OFF 
     
     The CHIME MODE OFF message will appear 
    for about 2 seconds then disappears. To display 
    this message again (to determine whether 
    chime mode is on or off), simply press and hold 
    down the CHIME key for 5 seconds.  
     
     
     
     
     
     
     
     
     
     
      
    						
    							 
     
    – 42 – 
    Viewing Alarm Company Messages 
    General Information 
    Users of the system may periodically receive messages on their display 
    screens from their monitoring agency or installer. When a message is waiting 
    to be viewed, the message shown below will appear. 
    MESSAGE. PRESS 0 
    FOR 5 SECS. 
    1.  Press and hold down   0  key for 5 seconds. 
    2.  The message could take up to four screens to display all the information 
    available. 
    NOTE: Any message sent by the central station downloader may be viewed 
    at any partition’s keypad. 
     
     
     
     
     
     
     
     
     
     
     
     
     
     
      
    						
    							 
     
    – 43 – 
    Panic Keys 
    (For Manually Activating Silent and/or Audible Alarms) 
    Using Panic Keys 
    Your system may have been programmed to use special key combinations to 
    manually activate panic functions. The functions that might be programmed 
    are Silent Emergency, Audible Emergency, and Personal Emergency. See 
    your installer for the function(s) that may have been programmed for your 
    system. 
     
    Active Panic Functions 
    (Your installer should note which 
    function(s) is active in your 
    system.) 
    Keys Zone Function 
    1 and *  995   
    3 and #  996   
    * and #  999   
    A 995  
    B 999  
    C 996  
      
    To use a paired key panic function, 
    simply press both keys of the assigned 
    pair at the same time.  
    If your keypad(s) have lettered keys for 
    panic functions, press the designated 
    key and hold down for at least 2 seconds 
    to activate the panic function.
    A silent emergency sends a silent alarm signal to the central station, but 
    there will be no audible alarms or visual displays. 
    An audible emergency sends an emergency message to the central station 
    (if connected) and will sound a loud, steady alarm at your keypad and at any 
    external sounders that may be connected (ALARM plus a zone number 
    would also be displayed). 
    A personal emergency alarm sends an emergency message to the central 
    station (if connected) and will sound at Keypads, but not at external 
    Notification Appliance Circuits. (ALARM plus a zone number would also be 
    displayed.) 
     
      
    						
    							 
     
    – 44 – 
    Relay Control 
    General Information 
    Your system may be set up using a relay so that a door (such as in a lobby) 
    can be unlocked momentarily using a keypad command.  Ask your installer if 
    this has been done in our system. 
    Executing 
    To activate the relay enter your security code + [0] at the keypad.  The door 
    will unlock for 2 seconds. 
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
      
    						
    							 
     
    – 45 – 
    Using #70 Relay Menu Mode 
    General Information 
    Your system may be set up so that certain lights or other devices can be 
    turned on or off by using the #70 command from a keypad. Ask your installer 
    if this has been done in your system. 
    To activate relays from a keypad, enter 4-digit security code + [#] +70. 
    Follow the keypad prompts described below. 
    NOTE: Your installer may have restricted the use of this function.  Please 
    check with your installer. 
     
    ENTER DEVICE NO. 
    00=QUIT 01 
    Enter the 2-digit number of the device to be 
    activated. 
    Note that if an invalid number is entered, the 
    system will simply ask you to reenter the number. 
    NN    DEVICE IS OFF 
    HIT  0=OFF ,  1=ON 
    Press 0 or 1 to turn the device off or on respectively. 
    nn represents the 2-digit device number and voice 
    descriptor is the relay voice descriptor programmed 
    by the installer. 
    NN    DEVICE IS OFF 
    HIT THE ✴ KEY 
    From a keypad, press ✴ to continue. The ENTER 
    DEVICE NO. prompt will appear.  
    						
    							 
     
    – 46 – 
    Using Schedules 
    Delaying the Closing Time 
    Your systems programmed schedules may automatically arm the system at a 
    predetermined time. In the event a user must stay on the premises later than 
    usual, users with master or manager authority levels can manually delay the 
    automatic arming (closing) time up to 2 hours. To delay the closing time: 
    1.  Enter your security code (master or manager authority levels only). 
    2. Press the  # 
     key, followed by 82. 
    3.  A menu prompt will be displayed, asking for the number of hours of delay.  
     
    CLOSING DELAY? 
    KEY 0-2 HOURS 
    Enter the desired number of hours of delay, 1 or 2. 
    The system automatically exits this mode after 
    entry.  
    Note that the delay is from the scheduled closing time, not from the 
    time the command is entered.  
    IMPORTANT: The selected delay cannot be reduced once it is set. A 1-
    hour delay can be increased to 2 hours, though. 
    4.  The system will automatically send a message to the central station 
    informing them that the programmed schedule has been changed. 
    Temporary Open/Close Schedules 
    Temporary schedules allow you to override the normal schedules 
    programmed by the installer. Temporary schedules can be in effect for up to 
    one week, and take effect as soon as they are programmed. 
    They are comprised of an arming (closing) time window and a disarming 
    (opening) time window. A time window is simply a defined period of time, at 
    the end of which arming or disarming will occur. 
    Before programming, use a worksheet similar to the one below to plan your 
    schedule. This will make it easier when actually programming the schedule. 
    Arm/Disarm Mon Tue Wed Thu Fri Sat Sun 
    Windows 
           
    Disarm Window 
           
     Start Time  HH:MM        
     Stop Time   HH:MM        
    Arm Window 
           
     Start Time  HH:MM        
     Stop Time   HH:MM         
    						
    							 
     
    – 47 – 
    Using Schedules (cont’d) 
    Programming Temporary Schedules 
    Temporary schedules only affect the partition from which it is entered. 
    Temporary schedules can be reused at later dates simply by scrolling (by 
    pressing #) to the DAYS? prompt (described below) and activating the 
    appropriate days. This should be considered when defining daily time 
    windows. Note that only users with authority level of manager or higher can 
    program temporary schedules. 
    To program temporary schedules: 
    1.  Enter your security code. 
    2. Press the  #
      key followed by 81. 
    3. The following prompts will appear. 
    MON  DISARM WIND. 
    07:45AM  08:45AM 
    The cursor will be positioned on the tens of hours 
    digit of the start time for Mondays disarm 
    window. Enter the desired hour. Press * to move 
    to the minutes field. The minutes are entered in 
    the same manner. The AM/PM indication is 
    changed by hitting any key, 0-9, while the cursor 
    is under the letter A/P position. Repeat for the 
    stop time entry. Press the * key to move to the 
    arming window for Monday. 
    Press # to move to the next screen display 
    without making changes. 
    MON   ARM WINDOW 
    07:45AM  08:45AM 
    The cursor will be positioned on the tens of hours 
    digit of the start time for the arm window. Repeat 
    the previous steps to enter the start and stop 
    time for Mondays arming window. 
    TUE  DISARM WIND. 
    07:45AM  08:45AM 
    After the windows for that day have been 
    completed, the system will prompt for disarm and 
    arm time windows for the next day. Repeat the 
    procedure for all days of the week. 
    When all of the days have been completed, the 
    system will ask which days are to be activated. 
      
    						
    							 
     
    – 48 – 
    Using Schedules (cont’d) 
    DAYS ?   MTWTFSS 
    HIT 0-7  X   X 
    This is the prompt that actually activates the 
    temporary schedule, and allows the temporary 
    schedule to be customized to a particular weeks 
    needs. To select the days that are to be activated, 
    enter the desired number 1-7 (Monday = 1). An 
    X will appear under that day, indicating the 
    previously entered schedule for that day is active. 
    Entering a days number again will deactivate 
    that day.  Pressing 0 will turn all days on/off. 
    The temporary schedule will only be in effect for 
    the days which have the letter x underneath 
    them. As the week progresses, the days are reset 
    to the inactive state. 
    When completed, press * to exit the temporary 
    schedule entry mode. 
      
    						
    							 
     
    – 49 – 
    Programming Device Timers 
    General Information 
    Device timers consist of an ON time and an OFF time, and selected days of 
    the week in which they are active. There are up to 20 timers that can be used 
    to control various devices, such as lights or appliances. Your installer will 
    have programmed the appropriate devices into the system (up to 96 devices 
    can be programmed).  
    Each timer controls a single device (designated as an output number) that 
    you select. For example, timer 1 might be set to turn the porch lights on at 
    7:00pm and turn them off at 11:00pm. Timer 2 might turn on the air 
    conditioner Monday-Friday at 4:30pm to cool the premises before you arrive 
    at 5:00pm, and turn it off at 10:00pm when you are retiring for the night. If 
    desired, different timers can control the same device. For example, timer 2 
    could be used Monday-Friday as in the previous example, and timer 3 could 
    be set to turn the air conditioner on and off at different times Saturday and 
    Sunday. 
    To enter the device timer menu mode:  
    Enter your security code, then press the   # 
     key followed by 83. 
    OUTPUT TIMER # ? 
    01-20,00=QUIT 01 
    Up to 20 timers can be programmed. A number 1-
    20 identifies each timer. Enter the desired timer 
    number to be programmed (1-20). Press * to 
    accept entry. 
    06 07:00P 11:45P 
    PORCH LITE    04 
    If that timer number has already been 
    programmed, a summary screen will appear. In 
    this example: 
      06 = Timer # 
      04 = Output Device # affected by this timer  
      PORCH LITE = Output Descriptor for Device 4 
      07:00PM = Start Time; 
      11:45PM = Stop Time 
    Press * to continue.  
    See your installer for 
    device numbers. 00 ENTER OUTPUT# 
     00 
    Enter the desired output device number (1-96). 
    As the number is entered, the devices description 
    will appear. 
    To delete a previously programmed timer, enter 
    00 as the output number.  
    						
    							 
     
    – 50 – 
    Programming Device Timers (cont’d) 
     
    00 ON TIME ? 
    00:00 PM 
    Enter the time you want the device turned on 
    using 00:01 - 11:59 format. When the display 
    shows the desired time, press the * key to move 
    to the AM/PM field. Press any key 0-9 to change 
    the AM/PM indication. 
    Enter 00:00 if this timer is not being used to turn 
    something ON for the days selected below. (Ex. 
    using one timer to turn lights on one day and 
    using another timer to turn them off on another 
    day). 
    00 OFF TIME ? 
    00:00 PM 
    Enter the time you want the device turned off 
    using 00:01 - 11:59 format. When the display 
    shows the desired time, press the * key to move 
    to the AM/PM field. Press any key 0-9 to change 
    the AM/PM indication. 
    Enter 00:00 if this timer is not being used to turn 
    something OFF for the days selected below. (Ex. 
    using one timer to turn lights on one day and 
    using another timer to turn them off on another 
    day). 
    00 DAYS? MTWTFSS 
    HIT 0-7      X   X 
    Select the days on which the device is to be 
    activated by entering 1-7 (Monday = 1). An X 
    will appear under that day, indicating the output 
    for that day is active. Entering a days number 
    again will deactivate that day. Pressing 0 will 
    turn all days on/off. The outputs will only be in 
    effect for the days that have the letter x 
    underneath them. As the week progresses, the 
    days are reset to the inactive state, unless the 
    permanent option is selected (next screen 
    prompt). When completed, press * to continue. 
    00 PERMANENT ? 
    0 = NO, 1 = YES     0 
    Answering 1 (YES) means the system executes 
    this timer continuously. Answering 0 (NO) means 
    the system executes each days output only once. 
     
      
    						
    All Honeywell manuals Comments (0)

    Related Manuals for Honeywell control panel VISTA128FBPVISTA250FBP User Manual