Honeywell control panel VISTA128B User Manual

 
 
– 11 – 
Functions Of The Keypad
 
1OFF
4MAX
7INSTANT
READY
2AWAY
5TEST
8CODE
03
STAY
6BYPASS
#
ARMED
READY
6160-00-002-V1
9CHIME
A
B
C
D
SPEAKERLCD
DISPLAY
FUNCTION
KEYS LEDS
 
 
 
IMPORTANT! When using the keypad to enter codes and commands, 
sequential key depressions must be made within 3 seconds of one 
another. If 3 seconds elapses without a key depression, the entry is 
aborted and must be repeated from its beginning.  

 
 
– 12 – 
Functions Of The Keypad (cont’d)
ALPHA DISPLAY WINDOW: A 2-line, 
32-character Liquid Crystal Display (LCD).  
Displays protection point identification and 
system status, messages, and user 
instructions.  
1 OFF
  :  Disarms the burglary portion of 
the system, silences alarms and audible 
trouble indicators, and clears visual alarm 
trouble after the problem has been 
corrected.   
2 AWAY
  :  Completely arms both 
perimeter and interior burglary protection 
by sensing an intruders...

 
 
–13 – 
Functions Of The Keypad (cont’d) 
✳
 READY  :  When depressed prior to 
arming the system, the keypad will display 
all open protection zones within the 
keypads home partition. This key is also 
used to display all zone descriptors that 
have been programmed for your system, by 
holding the key down for at least 5 seconds. 
#        
  :  Permits ARMING of the system 
without use of a security code (Quick 
Arm, if programmed).  
KEYS 0-9:  Used to enter your individual 
security access...

 
 
– 14 – 
Entry/Exit Delays 
General Information 
Your system has installer-programmed time delays, known as exit delay and 
entry delay. Whenever you arm your system, exit delay gives you time to 
leave through the designated exit door without setting off an alarm. Exit 
delay begins immediately after entering any arming command, and applies to 
all modes of arming protection. If programmed, a slow beeping will sound 
throughout the exit delay period. 
Entry Delay gives you time to disarm the system...

 
 
– 15 – 
Security Codes & Authority Levels 
General Information 
At the time of installation, you were assigned an authority level and a 
personal four-digit security code, known only to you and yours. The security 
code must be entered when arming and disarming the system. The authority 
level defines the system functions that you can perform.  
As an additional safety feature, other users that do not have a need to know 
your code can be assigned different security codes, and each user can be given...

 
 
– 16 – 
Security Codes & Authority Levels (cont’d) 
Authority Levels 
Authority levels define the system functions a particular user can perform. 
Depending on the authority assigned to you, there are certain system 
functions you may be prohibited from performing. In summary, there are six 
authority levels, each having certain system restrictions as shown below. 
Level 1 Master:  Can perform all system functions in assigned 
partitions, and can add, delete or change Manager 
and Operator level...

 
 
– 17 – 
Security Codes & Authority Levels (cont’d) 
General Rules on Authority Levels and Changes 
x
A user may not delete or change the user code of the SAME or HIGHER 
authority than which he is assigned. 
x
A user may only ADD users to a LOWER authority level. 
x
A user may assign access codes only to those partitions to which the user 
adding the code has access. (ex. a user with access to only partition 1 
cannot assign codes in partition 2.) 
x
The only way to assign a users authority level is...

 
 
– 18 – 
Security Codes & Authority Levels (cont’d) 
To Add a User 
IMPORTANT: Temporary users should not be shown how to use any system 
function they do not need to know (e.g. bypassing protection zones). 
1.  Enter Master or Manager code and press the  8 CODE
    key. 
2.  Enter the new users 3-digit User Number (002-150). 
3.  Enter 4-digit security code for that user. The following prompts will 
appear. 
ADD NEW USER? 
0  = NO , 1  = YES
Enter 1 to add a new user code. Entering 0 will 
change the...

 
 
– 19 – 
Security Codes & Authority Levels (cont’d) 
GLOBAL ARM ? 
0 = NO , 1 = YES
Press 1 (YES) if this user will be allowed to try to 
arm more than one partition at the same time. 
Press 0 if this user will arm only his assigned 
partition. 
PART.2 - SHOP? 
0 = NO , 1 = YES
The keypad now prompts for the user’s access to the 
next partition (see GOTO command). Again press 0 
or 1.  If yes, the system will automatically assign a 
user number for use in that partition and will 
prompt for authority...

 
 
– 20 – 
Security Codes & Authority Levels (cont’d) 
To Change a Users Code 
1.  Enter Master or Manager code and press the 8 CODE  key + user 
number to be changed. 
2.  Enter the new code for that user.  
ADD NEW USER? 
0 = NO , 1 = YES
The system will recognize that the user number is 
already in use and will prompt whether or not this 
is a new user.  Enter 0 to change the existing 
users code to the code entered in step 3.
  
USER  002  CHANGED 
SUCCESSFULLY 
The system will confirm that the...