Honeywell control panel VISTA10P Security System User Manual

							 
 
– 21 – 
Bypassing Protection Zones
Bypassing Protection Zones Bypassing Protection Zones
Bypassing Protection Zones 
  
 
 
Quic
Quic Quic
Quick Bypass
k Bypassk Bypass
k Bypass 
  
 
If  programmed,  Quick  Bypass  allows  you  to  easily 
bypass  all  open  (faulted)  zones 
without  having  to  enter  zone  numbers  individually.  This  feature  is  useful  if,  for 
example, you routinely leave certain windows open w hen arming at night. 
 
1.                 +   6  + [#] 
  (Security Code) BYPASS 
  In a few moments, all open zones will be  displayed and automatically bypassed. Make sure  
that only those zones that you wish to leave 
unprotected are bypassed, and that there are no 
other zones unintentionally left open.
 
Alpha Display: 
DISARMED  
HIT * FOR FAULTS  Fixed-Word Display:  NOT READY 
   
2. Wait for all bypassed zones to be displayed, then  
arm the system as desired. 
Ask your installer if Quick Bypass is active for 
your system, and if so, check here: 
    
DISARMED BYPASS 
READY TO ARM  Fixed-Word Display: BYPASS 
  
						

							 
 
– 22 – 
Chime Mode
Chime Mode Chime Mode
Chime Mode 
  
 
 
CHIME mode alerts you to the opening of a perimeter
 door or window while the 
system is disarmed. When Chime mode is activated:      Three tones sound at the keypad whenever a perimet er door or window is opened.  
    Interior zones do not produce a tone when they are  faulted. 
    Pressing the  READY key will display the open protection points. 
    Chime mode can be used only while the system is di sarmed. 
 
To turn Chime Mode on/off 
(system must be 
disarmed)
:  
    
             +    9 
  (Security Code) CHIME 
  The CHIME message appears when on. Perimeter  zones will cause a tone when faulted.
 
 
DISARMED CHIME 
READY TO ARM  Fixed-Word Display:  CHIME 
  The CHIME message disappears when Chime mode is of f. 
Voice Chime:  You can set the Voice Keypads (if installed) to an nounce faulted 
(opened) entry/exit or perimeter zones whenever nor mal Chime mode is on. 
 
To turn Voice Chime Mode on or off:  #  +   0   +   2  +   4    
(normal Chime mode must be on first)
 
When Voice Chime is on, faulted zones cause a voice  status announcement, chime 
and display. When off, the sounder still provides c hime if normal Chime mode is on. 
 
  
						

							 
 
– 23 – 
 
  
 Date and Time
Date and TimeDate and Time
Date and Time 
  
 
 
Viewing the Current Date and Time
Viewing the Current Date and Time Viewing the Current Date and Time
Viewing the Current Date and Time 
  
 
The master user can view the system time and date s
etting on alpha keypad. Other 
users can view the date/time if a function key has  been programmed to do so. 
 
  
             +[#] + [6] [3] 
  (Master Code) 
OR, press the function key (A, B, C, or D) for view ing 
current date and time, if programmed.
 
Alpha Display: 
DISARMED 
READY TO ARM  
   
A typical time/date display is shown.  
The display will remain on for about 30 seconds or  
until a key is pressed.  TIME/DATE        SAT 
12:05AM_05/09/00 
 
 “ A ”     “ B ”   “ C ”   “ D ”  
 
                                                          
If one of the above keys has been programmed for th e date/time 
display feature, place a check mark in the box bene ath that key. 
Setting the Date and Time
Setting the Date and Time Setting the Date and Time
Setting the Date and Time 
  
 
You can set the time and date by doing the followin
g: 
1.    
             +[#] +  [6] [3] 
  (Master Code) 
Alpha Display: 
DISARMED 
READY TO ARM  
   
2.  Press [] when the time/date is displayed.  
  A cursor appears under the first digit of the hour . 
  To move cursor ahead, press [
].  
To go back, press [#]. 
   Enter the 2-digit hour setting. 
   Enter the 2-digit minute setting. 
   Press [1] for PM or [2] for AM. 
   Enter the last two digits of the current year. 
   Enter the 2-digit month setting. 
   Enter the 2-digit day setting. 
3.  To exit, press [ ] when cursor is at the last digit, 
or wait 30 seconds.  
TIME/DATE        SAT 
04:04PM 10/17/00 
Current time display   
TIME/DATE        SAT 
04:04P2000/10/17 
Time/date editing display 
  
						

							 
 
– 24 – 
Panic Keys
Panic Keys Panic Keys
Panic Keys 
  
 
 
Using Panic Keys
Using Panic Keys Using Panic Keys
Using Panic Keys 
  
 
Your system may have been programmed to use special
 keys to manually activate 
emergency (panic) functions as follows:  
This Function  Sends this signal*  With This Sounding … 
Silent Alarm  silent alarm   no audible alarm and no  change in 
normal display to indicate that a silent 
alarm has been initiated. 
Audible Alarm  audible alarm  a loud, steady alarm at keypad(s) and at 
any external sounders that may be 
connected.  
Personal Emergency  auxiliary alarm  steady alarm sound at keypad(s), but not 
at external bells or sirens. 
Fire Alarm  fire alarm   temporal (pulsing) sound at  external 
bells and sirens. 
*All panic functions send signals to the Central Monitoring Station, if connected.  
To activate a Panic Function:  
Press and hold down for at least 2 seconds whicheve r 
lettered key on the keypad has been programmed for  
the desired emergency function.  
OR 
Press both keys of the assigned key pair at the sam e 
time. 
 
Alpha Display: 
DISARMED 
READY TO ARM  Fixed-Word Display:  READY  Typical Panic Alpha Display: 
ALARM 99 
  Fixed-Word Display: 99 and ALARM 
 
1OFF4MAX7INSTANTREADY
2AWAY5TEST8CODE0 3
STAY6BYPASS9CHIME#
ARMED
READY
6160-00-003-V0
A
B
C DZONE 95
ZONE 96 ZONE 99
 
PRESS BOTH KEYS
 
OF DESIRED PAIR
AT THE SAME TIME
4MAX
7INSTANT
2AWAY5TEST
8CODE
0 3
STAY6BYPASS9CHIME
#
ARMED
READY
6160-00-004-V0
ZONE 95
ZONE 99
ZONE 96
1OFF
READY
 
Lettered Panic Keys  Panic Key Pairs 
 
See your installer and use the chart provided in th e Features Programmed in Your 
System  section to note the functions that have been progr ammed for your system.   
						

							 
 
– 25 – 
Macro K
Macro K Macro K
Macro Key Programming & Usage
ey Programming & Usageey Programming & Usage
ey Programming & Usage 
  
 
 
About Macro Keys
About Macro Keys About Macro Keys
About Macro Keys 
  
 
The “A”, “B”, “C” or “D” keys can be used to automa
tically activate a series of 
commands of up to 16 keystrokes, if programmed for  this function. These keystrokes, 
as a group, are called “macros” and are stored in t he systems memory.  
    Typical macro functions can include: 
    - Arming sequences: STAY, Night-STAY, INSTANT, or  AWAY 
    - Bypassing particular zone(s)  
    - Activating relay(s) for turning on (or off) lig hts, fans, etc. 
    One macro can be assigned. 
    Macros can be activated only by users with authori ty levels authorized to 
perform the macro’s function. 
  
NOTE:   The  installer  must  activate  the  desired  function  k ey  before  macros  can  be 
assigned. See the chart at the back of this manual  for the key(s) assigned for macros. 
   
1.                 +  [#] + [6] + [6] 
  (Master Code)   
Alpha Displays: 
DISARMED 
READY TO ARM  
   
  If a macro has been previously defined, the 
keystrokes are shown on the bottom line of the  
display, otherwise the display is blank. 
  To exit this mode (and keep the existing macro  definition), press any key except the [ ] key. The 
system returns to normal mode. 
  To define a macro for the selected key, press [ ] 
and continue with the next prompt.  MACRO DISPLAY 
 
 
   
2. Enter the first of the series of desired commands,  
(do not include your master code), then press/hold 
the “D” key for at least two seconds to complete th e 
first command. This key terminates each  
command, and appears as an “F” in the keypad 
display. 
MACRO PGM 
 
 
  
						

							 
 
– 26 – 
Macro Key Programming & Usage 
Macro Key Programming & Usage  Macro Key Programming & Usage 
Macro Key Programming & Usage (cont.)
(cont.) (cont.)
(cont.) 
  
 
 
  The keypad beeps to acknowledge your input and displays the command you entered (followed by “F”).
 
3.  Enter the next command, followed by press/holdin g 
the “D” key for at least two seconds. The keypad  
beeps and displays the keystrokes entered so far. 
4.  Repeat until all the desired commands (up to 16  characters including the “F”s) have been entered . 
  Be sure to check your keystrokes before continuing . 
If you made a mistake, you must start over.  
5.  To exit, press/hold the “D” key for at least two  
seconds. The display returns to system status and  
indicates system is ready.  
Typical Macro Alpha Display: 
MACRO PGM 
6 0 2 F 0 3 F#7 0 1 F 2 F 
  
 
 
Example of Macro Programming
Example of Macro Programming Example of Macro Programming
Example of Macro Programming 
  
 
Suppose you want to (1) bypass the two upstairs win
dow zones, then (2) turn on an 
exterior light, and then (3) arm the security syste m in the AWAY mode. The 
procedures in the table that follows show you how y ou would program this macro: 
 Function Keystrokes Required Keypad Display 
1.  Bypass zones 02 & 
03   Press 
BYPASS [6]  key, then  
2-digit zone number 02, then  
terminator “D”’ then [6], then 2-digit 
zone number 03, then terminator “D”. 6 0 2 F 6 0 3  
2.   Insert terminator.  Press the “D” key for at least  2 seconds. 6 0 2 F 6 0 3 F  
3.  Turn light on  
      (device 01).  Press [#] and 7 keys for “device ON”,  
and [01] key for selecting device 1. 6 0 2 F 6 0 3 F#7 0 1 F  
4.
  Insert terminator.  Press the “D” key for at least  2 seconds. 6 0 2 F 6 0 3 F#7 0 1 F 
5.  Arm system AWAY  Press  AWAY [2]  key. 6 0 2 F 6 0 3 F#7 0 1 F 2 
6.  Insert terminator.  Press the “D” key for at least  2 seconds. 6 0 2 F 6 0 3 F#7 0 1 F 2 F 
7. Exit Macro mode  Press the “D” key again.  
Using a Programmed Macro Key
Using a Programmed Macro Key Using a Programmed Macro Key
Using a Programmed Macro Key 
  
 
  
 
DISARMED 
READY TO ARM  
1. Press the Macro key programmed for the desired  
series of commands for at least 2 seconds. The “Ent er 
User Code” prompt appears. The prompt remains  
displayed for up to 30 seconds.
    
ENTER USER CODE 
* * * * 
2. Enter your 4-digit security code.  
  The programmed macro sequence begins 
automatically after the user code is entered.
   
						

							 
 
– 27 – 
Us
UsUs
Using Device Commands
ing Device Commandsing Device Commands
ing Device Commands 
  
 
 
About Device Commands
About Device Commands About Device Commands
About Device Commands 
  
 
Your system may be set up so that it can control ce
rtain lights or other devices. 
    Some devices may be automatically turned on or off  by the system. 
    You may be able to override automatically controll ed devices using the 
commands described below. 
    Some devices can be manually turned on or off usin g the commands described 
below. 
    See your installer for a list of devices that may  be set up for your system. A list 
of these devices is provided at the back of this ma nual for you to fill out.  
 
To Activate Devices:  
  
             +  [#] + [7] + 2-digit device number 
  (Security Code)   
Devices associated with that device number activate . 
  
To Deactivate Devices: 
  
             +  [#] + [8] + 2-digit device number 
  (Security Code)   
Devices associated with that device number deactiva te. 
Alpha Display: 
DISARMED 
READY TO ARM 
 
Fixed-Word Display:  READY 
  
						

							 
 
– 28 – 
Paging Feature
Paging Feature Paging Feature
Paging Feature 
  
 
 
About Automatic Paging
About Automatic Paging About Automatic Paging
About Automatic Paging 
  
 
Your system may be set up to automatically send ale
rt messages to a pager as certain 
conditions occur in your system.     The following events can be programmed by your ins taller to be sent to the pagers: 
arming and disarming
†, alarms, and trouble conditions. (†  reports when 
arming/disarming from a keypad using a security cod e; auto-arming/disarming, 
arming with assigned button, and keyswitch arming d o not send pager messages.) 
   You can also program the system to send an automat ic pager message to alert you 
in the event that someone has not arrived home (dis armed the system) within a 
defined period of time (see the  Scheduling section for details on “latch key report”). 
   Your installer programs the pager phone numbers an d reporting events. 
   The pager message consists of a 7-digit system sta tus code that indicates the type of 
condition that has occurred. 
   An optional, predefined 16-digit character string  can precede the 7-digit system 
status code; these characters can consist of a PIN  no., subscriber account no., or any 
additional data that you may wish to have sent to t he pager. 
   The pager display format is as follows: 
3-digit Event Code    



 Optional 16 digits 

  AAAAAAAAAAAAAAAA
 – BBB  – CCCC  

 1 or 0 + 3-digit
 User or Zone No.   A =  B =  C = 
Optional 16-digits for 
Account numbers, 
PIN numbers, or any  
other data; 
programmed by the 
installer, if required.  A 3-digit code that 
describes the event  
that has occurred  
in your system 
(see for event 
codes table below)  4-digit number consisting of 1 or 0 plus a 3-digit 
User or 
Zone number, depending on the type of event that ha s 
occurred, where: 
 alarms and troubles display zone number  arming/disarming (opens/closes) display user numbe r  single-digit user or zone numbers are preceded by a 
zero.
  The 3-digit Event Codes (BBB) that can be displayed  are: 
911 =  811 =  101 =  102 = 
Alarms. 
The 4-digit number  
(CCCC) represents the 
zone number  that has 
caused the alarm.  Troubles. 
The 4-digit number 
(CCCC) represents the 
zone number  that has 
caused the trouble.  Open 
(system disarmed). 
The 4-digit number 
(CCCC) represents the 
user number  that has 
disarmed the system.  Close 
(system armed). 
The 4-digit number 
(CCCC) represents the 
user number  that has 
armed the system.  
 
Examples of typical 7-digit pager displays follow.  
Ex. 1.   9 1 1 – 1 0 0 4  
 =   A larm (911) on zone 4 (10 04);  
Ex. 2.    1 0 2 – 1 0 0 5  
 = Closing–system arming (102)– by user 5 (10 05)   
						

							 
 
– 29 – 
Pag
Pag Pag
Paging Feature
ing Featureing Feature
ing Feature 
  
 
 
Manual Paging
Manual Paging Manual Paging
Manual Paging 
  
 
Your system may be set up so you can manually send 
a message to a pager. 
    Your installer programs the paging function key an d the pager phone number. 
    Pressing the paging keys sends the message 
  9 9 9 – 9 9 9 9   to the pager . 
 
  This message could mean “call home”, “call your off ice”, or any other prearranged 
meaning. 
    See the Paging chart at the back of this manual fo r details of the paging setup for 
your system. 
 
1.  Hold 
pager key 2 seconds. 
  Press and hold the programmed Paging Key for at  least 2 seconds (wait for beep). 
2.  The recipient, on seeing the 999–9999 message,  will understand the prearranged meaning of this  
signal. 
 Alpha Display: 
DISARMED 
READY TO ARM 
  
Fixed-Word Display:  READY 
 
999-9999 
Pager Display 
 
Latch Key Paging
Latch Key Paging Latch Key Paging
Latch Key Paging 
  
 
You can program a schedule that causes a pager repo
rt to be sent if the system is not 
DISARMED by the scheduled time (see  Scheduling section, event “03”). For example, 
a working parent might want a message to be sent to  a pager if their child did not 
arrive home from school and disarm the system by a  certain time. 
If programmed, the message that is sent is: 
  7 7 7 – 7 7 7 7  .  
						

							 
 
– 30 – 
Security Codes & Authority Levels
Security Codes & Authority Levels Security Codes & Authority Levels
Security Codes & Authority Levels 
  
 
 
About Security Codes
About Security Codes About Security Codes
About Security Codes 
  
 
Your installer assigned a master code that is used 
to perform all system functions. 
In addition, you can assign up to 15 different secu rity codes for use by other users. 
   Only the System Master can assign security codes t o users. 
   Users are identified by 2-digit user numbers (03-1 7 [users 01 and 02 are reserved]). 
   In addition to a security code, each user is assig ned various system attributes. 
   Security codes can be used interchangeably when pe rforming system functions (a 
system armed with one users code can be disarmed b y another users code), with 
the exception of the Guest code and Arm Only code d escribed below. 
   Security code programming involves these steps:  
  1.  Choose a user number and assign a 4-digit secur ity code. 
  2.  Assign an authority level to that user.  
  3.  Assign other attributes as necessary (see attri butes on the next page). 
 
NOTE: The factory settings are designed to meet most nor mal user situations. 
Therefore, the only step you usually need to do whe n adding users is assign a user 
number and a security code.  
Authority Level Definitions
Authority Level Definitions Authority Level Definitions
Authority Level Definitions 
  
 
Authority levels define the system functions a part
icular user can/cannot perform.   
Level  Title  Explanation   
N/A  System Master    Reserved for user 02; Can perfor m all system functions and assign 
codes; can change its own code as described on the following page.  
The default System Master code is 1234. 
0   Standard User  Can only perform security functions . Cannot perform system 
functions reserved for the master user. 
1   Arm Only  Can only arm the system. Cannot disarm  or do other functions. 
2   Guest  Can arm the system, but cannot disarm the  system unless the 
system was armed with this code. This code is typic ally assigned to 
someone (e.g., babysitter or cleaner) who has a need to arm/disarm 
the system only at certain times. The user of this code should not use 
the “Quick Arming” feature. 
3   Duress Code  Intended for use when you are forced  to disarm or arm the system 
under threat. When used, the system will act normally, but can 
silently notify the Central Monitoring Station of your situation, if that 
service has been provided.