Honeywell control panel LYNXRLYNXR24 User Manual

– 31 – 
 
 







*		

(QWU\(YHQW&RPPHQW
(PSW\ 1R HYHQW VFKHGXOHG RU VFKHGXOH LV WHPSRUDULO\ GLVDEOHG
; HYLFH 7XUQ DQ ; GHYLFH HLWKHU RQ RU RII DW EHJLQHQG WLPHV ZLOO
KDYH D VWDUW DQG HQG WLPH WR SURJUDPWLPH GULYHQ
127(6+$ VLUHQ FDQQRW EH XVHG
/DWFK .H\ 5HSRUW 6HQG D VSHFLDO SDJHU UHSRUW  LQGLFDWLQJ V\VWHP QRW
\HW GLVDUPHG ZLOO KDYH D VWDUWHQG WLPH WR VHQG WKH UHSRUW
ZLQGRZ GULYHQ UHSRUWV RQO\ WR SDJHU...

– 32 – 







%(	
(QWU\ D\
 ,QYDOLG GD\ HQWU\
R HYHQW RQ QH[W WLPH PDWFK RQ WKH QH[W 0RQGD\ ZLOO UHPRYH LWVHOI DIWHU H[HFXWLQJ
 R HYHQW RQ QH[W WLPH PDWFK RQ WKH QH[W 7XHVGD\ ZLOO UHPRYH LWVHOI DIWHU H[HFXWLQJ
 R HYHQW RQ QH[W WLPH PDWFK RQ WKH QH[W :HGQHVGD\ ZLOO UHPRYH LWVHOI DIWHU H[HFXWLQJ
 R HYHQW RQ QH[W WLPH PDWFK RQ WKH QH[W 7KXUVGD\ ZLOO UHPRYH LWVHOI DIWHU H[HFXWLQJ
 R HYHQW RQ QH[W WLPH PDWFK RQ WKH QH[W )ULGD\ ZLOO...

– 33 – 




-!#

 
The LYNXR-Series is equipped with a remote interactive phone capability that permits access to the 
security system from any off-site touch-tone telephone using all user codes. If this feature has been 
programmed, the system will provide the appropriate voice messages and any system beeping sounds 
indicating the status of the security system over the phone line. (Refer to Summary of Audible 
Notification for further information.) The following...

– 34 – 




-!#

 
Enter: ZLWKLQ HLJKW VHFRQGV
@
@
@
@ RU >@  >@
@  >@  GHYLFH QR
To remotely activate X-10 devices 7 & 8:  >@  >@  GHYLFH QR
@  >@  GHYLFH QR
To remotely deactivate X-10 devices 7 & 8:  >@  >@  GHYLFH QR
@  ]RQH QR
@  >@
@

– 35 – 

		




0




/

– 36 – 

		


1

#!

2
-

 


/

– 37 – 

		


(




/

– 38 – 







		
For additional security you (the Master User Code) can assign secondary user codes to individual users 
enabling them to perform specific system functions. These secondary users are identified by user 
numbers when their codes are assigned. You can assign up to 6 user codes (2-digit user numbers 03-
08). Note that the master user is the only one who can assign codes to secondary users, and is 
designated user no. 02; user no. 01 is the...

– 39 – 






3)%,
	!
The 7(67 key puts your system into the Test mode, which allows each protection point to be checked 
for proper operation. The keypad sounds a single beep every 45 seconds as a reminder that the system 
is in the Test mode.  
 
NOTE:  An alarm message will not be sent to your alarm monitoring company during the following tests.
 
 
Disarm the system and close all protected windows, doors, etc. The “READY” indicator...

– 40 – 






3	

!!	.
To silence the beeping sound for fault conditions, press any key. 
 
FAULT  Indicates that a problem exists with the zone(s) displayed, accompanied by rapid 
beeping. First, determine if the zone(s) displayed are intact and make them so if they are 
not. If the zone uses a wireless detector, check that changes in the room (moving 
furniture, televisions, etc.) are not blocking wireless signals from the detector. If the...