Honeywell control panel LYNXRLYNXR24 User Manual

– 11 – 


	






 
IRU RWKHU GLVSOD\V VHH7URXEOH 0HVVDJHV
ALARM
AWAYINSTANTSTAYFIREREC MESSAGEBYPASSFAULT
CHIME   TEST  LOW BAT  AC
  ALARM:   Appears when the system is armed and an intrusion has been detected (also appears during a 
fire alarm or audible emergency alarm). Accompanied by the protection zone that is in alarm. 
AWAY:  All burglary zones, interior and perimeter, are armed.  
INSTANT:  Entry delay is turned off. 
STAY:...

– 12 – 




		
Before arming your system, all protected doors, windows, and other protection zones must be closed or 
bypassed (see the BYPASSING PROTECTION section). Pressing the 
67$786 key will announce all 
zones that are faulted, as well as any other abnormal system condition, making it easier for you to 
secure any open zones. 
 
READY LIGHT:  The green READY indicator on the keypad will be lit if the system is ready to be 
armed.  If...

– 13 – 




	
Use this mode when you are staying home, but expect someone to use the entrance door later.  Close 
all protected perimeter windows and doors before arming.  The green READY indicator on the keypad 
should be lit if the system is ready to be armed. 
To arm in STAY mode: 
 67$

– 14 – 




	 % &
Use NO DELAY with STAY mode when you are staying home and do not expect anyone to use the 
entrance door. 
 
Use NO DELAY with AWAY mode when the premises will be vacant for extended periods of time such 
as vacations, etc.  
 
When armed with NO DELAY, the system will sound an alarm if a protected door or window is opened, 
including the entrance door. You may leave through the entrance door during the exit delay period...

– 15 – 





)
Exit delay begins immediately after arming the system, and gives you time to leave through the 
designated exit door without setting off an alarm.  A slow beeping will sound throughout the exit delay 
period, if programmed.  
 
Exit Alarms Exit Alarm Active     
  
 
To minimize false alarms sent to the alarm monitoring company, your system may have been 
programmed for this feature. Ask your installer if Exit Alarm is active for your...

– 16 – 




Use the 2)) key to disarm the system and to silence alarm and trouble sounds. See the SUMMARY 
OF AUDIBLE NOTIFICATION section for information, which will help you to distinguish between fire 
and burglary alarm sounds. 
 
IMPORTANT: If you return and the main burglary sounder is on, DO NOT enter the premises, but 
call the police from a nearby safe location. If you return after an alarm has occurred and the main 
sounder has shut itself off, the...

– 17 – 


 
!


*

Use the  BYPASS key when you want to arm your system with one or more zones intentionally 
unprotected. Bypassed zones are unprotected and will not cause an alarm when violated while your 
system is armed. 
All bypasses are removed when an OFF sequence (security code plus OFF) is 
performed. Bypasses are also removed if the arming procedure that follows the bypass command is 
not successful. 
The system will not allow...

– 18 – 


!

	


#
Your system may have been programmed to use special keys to manually activate panic functions. The 
functions that might be programmed are listed below. See your installer for the function(s) that may 
have been programmed for your system.  
 
Your installer should 
note the functions that 
are active in your 
system. 
Active Panic Functions
 
Keys Zone  Function 
1 and 
✻ 95 
3 and #  96 
✻ and #  99
 
To use a paired key panic...

– 19 – 




!
#



If the Paging feature has been programmed for your system, your pager will respond to certain 
conditions as they occur in your system by displaying a message that indicates the type of condition 
that has occurred. The message appears in a 7-digit format explained below. The system can also be 
programmed to send up to 16 additional digits that will appear in front of the 7-digit message. These 
16 digits may consist of a PIN number or special...

– 20 – 




$#%	&
#


+$,-	

If the “Follow Me” Announcement feature has been programmed your system will automatically dial a 
telephone number and deliver a voice message. The two different types of “Follow Me” messages 
include system and reminder announcements.  
System Announcements 
LYNXR/LYNXR24 can be programmed to trigger “Follow Me” system announcements by one or a 
combination of the following events: 
• Alarm 
•...