Home > Honeywell > Control panel > Honeywell control panel LYNX Plus User Manual

Honeywell control panel LYNX Plus User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Honeywell control panel LYNX Plus User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 178 Honeywell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							– 21 – 
    SECURING THE PREMISES
    SECURING THE PREMISESSECURING THE PREMISES SECURING THE PREMISES 
        
    Bypassing Protection Zones 
     
    Bypassing Individual Zones 
    Use the BYPASS key when you want to arm your system with one or more zones intentionally 
    unprotected. Bypassed zones are unprotected and will not cause an alarm when violated while your 
    system is armed. All bypasses are removed when an OFF sequence (security code plus OFF) is 
    performed. Bypasses are also removed if the arming procedure that follows the bypass command is 
    not successful. 
    The system will not allow fire zones to be bypassed. 
     
    The system must be disarmed first. 
    To bypass a zone(s): 
                            +  BYPASS + 2-digit zone number(s) 
    for zone(s) to be  
      Your user code  bypassed (e.g., 01, 02, 03, etc.)
     
     
    Important! All single-digit numbers must be preceded by a zero (for example, enter 01 for zone 1). 
     
    The keypad will provide a confirmation beep and display the word “Bypass” along with each bypassed 
    zone number. Wait for these zones to be displayed, to be sure that intended zones are bypassed. 
     
    Arm the system as usual when the keypad displays the READY LED on steady. 
     
    Forced Bypass 
    Your system may allow you to easily bypass all open (faulted) zones without having to enter zone 
    numbers individually. Ask your installer if this feature is active.
     
    To bypass a zone(s): 
                            +  BYPASS + 
    FUNCTION 
      Your user code   
    In a few moments, all open zones will be displayed along with the word “Bypass.” Wait for these zones 
    to be displayed before arming. Arming the system before zones are displayed eliminates all bypasses. 
     
    Arm the system as usual when the keypad displays the READY LED on steady. 
     
    Displaying Bypassed Zones 
    The system allows you to determine what zones have been previously bypassed. Bypassed zones can be 
    displayed only when the system is disarmed, and when the “Bypass” message described above is 
    displayed. 
    To display bypassed zone(s): 
                             +  BYPASS + WAIT
     
      Your user code 
     
    In a few moments, all open zones will be sequentially displayed along with the word “Bypass.” 
    						
    							– 22 – 
    SECURING THE PREMISES
    SECURING THE PREMISESSECURING THE PREMISES SECURING THE PREMISES 
        
    Panic Keys / Chime Mode 
     
    Panic Keys 
    Your system may have been programmed to use special keys to manually activate panic functions. The 
    functions that might be programmed are listed below. See your installer for the function(s) that may 
    have been programmed for your system.  
     
    Your installer should 
    note the functions that 
    are active in your 
    system. 
    Active Panic Functions 
    Keys Zone  Function 
    1 and ✻ 95 
    3 and #  96 
    ✻ and #  99 
    To use a paired key panic function, simply press both keys of the assigned pair at the same time. If 
    your keypad has lettered keys for panic functions, press the designated key and hold down for at least 2 
    seconds to activate the panic function. Panic keys can also be activated by wireless devices such as the 
    Ademco 5827. Ask your installer about this feature. 
     
    Types of Panic Alarms 
    A silent emergency/silent alarm sends an alarm signal to the alarm monitoring company,† but 
    there will be no audible alarms or visual displays. 
    An audible emergency/audible alarm sends an emergency message to the alarm monitoring 
    company† and sounds a loud, steady alarm at your keypad and at any external sounders that may be 
    connected (“Alarm” plus a zone number are also displayed).  
    A personal emergency/aux  alarm sends an emergency message to the alarm monitoring company† 
    and sounds at keypads, but not at external sounders. (“Alarm” plus a zone number are also displayed). 
    A supervised fire alarm sends a fire alarm message to the alarm monitoring company† and uniquely 
    activates keypad and any external sounders (“Fire Alarm” plus a zone number are also displayed). 
     † If your system is connected to an alarm monitoring company 
     
    Chime Mode 
    Your system can be set to alert you to the opening of a door or window, while it is disarmed, by using 
    CHIME mode. When activated, three beeps will sound at the keypad whenever a protected perimeter 
    door is opened and the zone voice descriptor will be announced. Pressing the STATUS key will display 
    the open protection points. 
    Note that the Chime mode can be turned on only when the system is disarmed. 
    To turn Chime mode on or off: 
    FUNCTION +  CHIME 
     
     
    The “Chime” message displays while Chime mode is on, and disappears from the display when Chime 
    mode is off.  
    						
    							– 23 – 
    USER FUNCTIONS
    USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
        
    Paging Feature 
     
    Automatic Paging 
    If the Paging feature has been programmed for your system, your pager will respond to certain 
    conditions as they occur in your system by displaying a message that indicates the type of condition 
    that has occurred. The message appears in a 7-digit format explained below. The system can also be 
    programmed to send up to 16 additional digits that will appear in front of the 7-digit message. These 16 
    digits may consist of a PIN number or special digits needed by the pager, account number, pauses, or 
    any other special characters you may choose (for example, you may want to use a special character code 
    to distinguish between security system messages and usual pager messages). See your installer if these 
    additional characters are desired. 
     
    Code Format 
    The Pager Code takes the following form:  (AAAAAAAAAAAAAAAA) EEE-0NNN 
    AAA… =  Optional 16 digits, programmed by your installer. 
    EEE     =   3-digit number describing the event that has occurred, as follows: 
      911 = Alarm (0NNN following indicates the zone that caused the alarm) 
      101 = Open, system disarmed (0NNN following indicates user number) 
      102 = Close, system armed (0NNN following indicates user number) 
      811 = Trouble (0NNN following indicates the zone that caused the trouble) 
    0NNN   =  First digit is always 0, followed by 3-digit user or zone number, depending on the 
    type of event that occurred.  
    Examples:  Pager display: 911–0004   
     Indicates the system is reporting an alarm (911) due to a fault on zone 4 (0004). 
     Pager displays: 
    101–0005  
      Indicates the system is reporting an open/disarm (101) by user 5 (0005). 
     
    Manual Paging 
    In addition, your system may have been programmed to send a unique pager message when the AUX 
    key is pressed (see AUX Function section for alternate function of this key). The actual message sent is 
    999-9999 (the hyphen may not appear, depending on your pager service). This code can be used to alert 
    the person with the pager to whatever meaning you pre-arrange (e.g., “call home”).  Ask your installer if 
    this has been done for your system. 
     
    To manually send the pager message, (if programmed): AUX (hold until 4 beeps sound) 
       
    						
    							– 24 – 
     
        USER FUNCTIONS
    USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
        
    “Follow Me” Announcement Feature 
     
    “Follow Me” Reminder and System Announcements 
    If the “Follow Me” Announcement feature has been programmed your system will automatically dial a 
    telephone number and deliver a voice message. The two different types of “Follow Me” messages include 
    system and reminder announcements.  
    System Announcements 
    The Lynx Plus Series can be programmed to trigger “Follow Me” system announcements by one or a 
    combination of the following events: 
    • Alarm 
    • Trouble 
    • Arming/Disarming (by a keyfob or users 5-8*)  
    *see Security Codes section for user code descriptions. 
    Ask your installer about the events that trigger “Follow Me” system announcements. 
    “Follow me” system announcements are delivered to a phone number that has been programmed by 
    your installer. The voice message is a repeatable system status message (i.e. “Disarm Ready to Arm” 
    when system was disarmed; “Armed Away” when system was armed; “Alarm Front Door” when an 
    alarm occurred, etc). In addition, a special repeatable voice message (“System, System…”) can be 
    triggered manually by pressing the AUX key on the keypad and holding it down for 4 seconds.  
    NOTE:  This is similar to the manual paging feature (see Paging Feature for details).  
     
    Reminder Announcements 
    The “Follow me” reminder announcement is triggered by the scheduler if  Reminder Announcements 
    has been chosen as Event Identifier (see Scheduling User interface for details).  
    NOTE: The “Follow me” reminder can only be used if the “Follow me” or Pager feature has been 
    programmed by your installer.  
    The “Follow me” reminder voice message is the same reminder that is played through a local speaker. 
    The reminder should be recorded by your installer. The “Follow me” reminder message will be delivered 
    to a phone number that your installer has programmed or that you can program by yourself.  If the 
    “Follow me” reminder phone number has not been programmed, or has been deleted, the reminder is 
    announced through a local speaker only.      
     
    After the “Follow me” system or reminder announcement is delivered you can terminate it by pressing 
    any key on the telephone keypad. If the message is not acknowleged/terminated  Lynx Plus Series will 
    attempt to deliver the message and will redial the “Follow Me” telephone number a maximum of eight 
    times.   
    						
    							– 25 – 
    USER FUNCTIONS
    USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
        
    “Follow Me” Announcement Feature  
    NOTES: (1)  The “Follow Me” announcement will be terminated if any new report needs to be sent or if 
    any key is pressed on the Lynx Plus Series keypad or a wireless (RF) keypad. The [✻] key on 
    a wireless keypad is ignored by the system when the “Follow me” feature is active and 
    cannot be used to terminate the announcement or request status. 
     (2)  If your Lynx Plus Series has been programmed to send “Follow Me” system messages upon 
    arming/disarming do not make any key strokes after you have disarmed the system (unless it 
    is necessary). Entering additional keystrokes will terminate the “Follow Me” message. 
     
    To program “Follow Me” reminder telephone number: 
     
    1.   Enter: 
                            +  FUNCTION  + [65] 
      Master user code  
    2.  The system will announce: “Enter follow me reminder phone number, press ADD to accept, press 
    ESCAPE to quit” and “Phn Follow Me Phone#” will be displayed. 
    NOTES:  (1)  The system will accept all digits including the star [✻], pound [#]. To insert a two (2) second pause 
    press the AUX key. 
     (2) If the ESCAPE key is pressed to cancel entry, the telephone number must be entered again. 
      (3)  Pressing any key on a wireless (RF) keypad will terminate this mode and the “Follow Me” telephone 
    number must be reentered. 
    3.  Enter up to 24 digits. After each digit is entered the system will announce the digit and it will be 
    displayed on the LCD screen. The system will not announce star, pound or pause, however “*” or 
    “#” will be displayed on the LCD screen. 
    4.  After you have entered the last digit press ADD to save the number. If 24 digits have been entered 
    the system will automatically save the number and exit the “Follow Me” announcement feature. 
    NOTE:  The “Follow me” reminder telephone number can be changed as often as necessary by repeating 
    steps 1 through 4. 
     
    To delete “Follow Me” reminder telephone number 
     
    1.   Enter:     
                        + FUNCTION + [65] 
        Master user code  
    2.  The system will announce: “Enter follow me reminder phone number, press ADD to accept, press 
    ESCAPE to quit” and “Phn Follow Me Phone#” will be displayed. 
    3.   Press ADD without entering any digits. 
     
     
      
    						
    							– 26 – 
    USER FUNCTIONS
    USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
        
    Using Powerline Carrier Device Commands 
    (Lights On/Lights Off Keys)
     
    General Information 
    Powerline Carrier devices (e.g. X10 brand devices) are programmable switches that can be used to 
    perform many different functions. Your system may be set up so that certain lights or other devices can 
    be turned on or off by using the device command from the keypad. Ask your installer if this has been 
    done in your system.  If programmed for your system, some devices may activate automatically upon 
    certain system conditions. In this case, the following commands can be used to override the device 
    activation. See your installer for a full explanation of this feature. 
     
    To activate X10 devices 01-06: FUNCTION  +   LIGHTS ON  + (2-digit) dev. no. (2 beeps) 
    To deactivate X10 devices 01-06:
     FUNCTION  +   LIGHTS OFF  + (2-digit) dev. no. (2 beeps) 
     
    To activate X10 devices 07 & 08**:                        +FUNCTION +LIGHTS ON + (2-digit) dev. no. (2 beeps) 
      Your user code  
    To deactivate X10 devices 07 & 08**:
                            +FUNCTION +LIGHTS OFF + (2-digit) dev. no. 
     Your user code  (2 beeps)  ** Devices 07 and 08 may be assigned to system devices, such as alarm bells, which should not be activated using 
    this command because they are activated automatically under certain system conditions.  See your installer and 
    the table below. Devices 09-16 are used for Multi-Mode (e-mail) event triggers. 
     
    Device Descriptions 
    See your installer for device numbers assigned for your system.  Device Description  
       01          
       02          
       03          
       04          
       05 
       06 
       07 
       08 
       09          
       10          
       11          
       12          
       13 
       14 
       15 
       16  
      
    						
    							– 27 – 
    USER FUNCTIONS
    USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
        
    Message Recording/Playback/Volume Control 
    The Lynx Plus Series Message Center allows you to record, play and delete messages. The maximum 
    message duration is 85 seconds. 
    NOTES: (1)  The Record/playback functions can only be performed from the master keypad.  It cannot be 
    performed from any other wireless keypad (ex. 5827). 
      (2)  If the system loses electrical power, all messages will be erased. 
      (3)  Message Play/Record will not be available if a report must be sent. 
      (4)  Individual messages cannot be played back or deleted. 
     
    Recording a Message 
    To record a message: FUNCTION  +  RECORD  
     
    The keypad displays “Rec Press Off to Stop”. Begin speaking into the microphone.  
    The recording will automatically stop after 85 seconds, if a message has been recorded. The keypad will 
    beep twice and “Msg” will be displayed. 
     
    To stop recording before the end of 85 seconds: Press OFF  
     
    The keypad will beep twice, the “Rec Press Off to Stop” display turns off, but “Msg” is displayed. 
     
    Additional messages can be recorded, as long as there is recording time remaining, by repeating the 
    above steps. 
     
    NOTE:  If you are trying to record a new message and the message center is already full, the system will 
    announce “End Message” and “Message Center Full” will be displayed. If the message center is 
    full all old messages must be deleted before new messages can be recorded. See Deleting 
    Messages section. 
     
    Message Playback 
    The display of “Msg” indicates that a new message is in memory. After playing the message, the 
    MESSAGE display turns off. See NOTE below if using a wireless keypad. 
    To play back a message: 
    FUNCTION  +  PLAY  
    All recorded messages will be announced sequentially. A short beep will sound between messages. 
    To skip a message: Press [
    ✻] 
    Deleting Messages  
    To delete all messages: 
    FUNCTION  +  PLAY  
    While the messages are being announced: Press 
    FUNCTION  +  DELETE  
    Two beeps will sound, confirming that the message(s) have been deleted. 
      
    						
    							– 28 – 
     
    USER FUNCTIONS
    USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
        
    Message Recording/Playback/Volume Control 
     
    Adjusting the Volume 
    The volume level of message playback, system announcements, and status beeps can be changed. You 
    can also mute system announcements if desired. See NOTE below if using a wireless keypad. 
     
    To adjust message playback/system announcement volume: 
     
    FUNCTION  +  VOLUME + [3] or [6] †      
    † [3] = increases volume one level, [6] = decreases volume one level. 
     
    Repeat the key sequence until the desired volume level is achieved. 
     
    To mute system announcements: 
    FUNCTION  +  VOLUME  +  OFF  
     
    When muted, no system announcements will be made.  Recorded messages will be announced, though, 
    when 
    PLAY is pressed. 
    To restore announcement sounding: 
    FUNCTION  +  VOLUME + [3] or [6] 
     
    Volume level will be restored to the level that was selected prior to muting the sound. 
     
    NOTE:  If a wireless keypad (5827) has been installed and is programmed for quick arming, it cannot be 
    used to activate message playback or adjust the volume. In this case, you must use the master 
    keypad to perform these functions.  
    						
    							– 29 – 
    USER FUNCTIONS
    USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
        
    AUX Function 
     
    General Information 
    The AUX key may have been programmed to either perform a predefined function or to send a preset 
    message to a pager/“Follow Me” system phone number (see the Pager Feature section for pager 
    operation or the Follow Me Announcement Feature section for “Follow Me” operation).  Ask your 
    installer which function has been assigned for your system. 
     
    AUX Key:     
    PRE-DEFINED FUNCTION     
    PAGING FUNCTION      
    FOLLOW ME VOICE MESSAGE 
     
    If programmed for the AUX function, you can use the AUX key to activate a string of up to 20 
    keystrokes that have been stored in the system’s memory.  Typical functions include: 
     • Seldom used but repeatable sequences 
     • Arming sequences that involve bypassing zones before arming 
     • Device activation sequences 
     
    Defining the AUX Function 
    The system must be disarmed before defining a function. 
    1. Enter 
                            +  FUNCTION  +  AUX (hold down at least 2 seconds until 4 beeps sound). 
    Master user code 
    2.  Press the desired command sequence, up to 20 keystrokes. Press the AUX key between each 
    command in the sequence. 
    3. Press the 
    AUX key twice to end the definition. 
     
    For example, to bypass Zones 10 and 11 and arm AWAY with NO DELAY, enter the following string: 
     
                           + FUNCTION +  AUX + [6] + [10] + [11] +  AUX +  AWAY + [0] +  AUX +  AUX 
    Master user code
      
     
    Note that the AUX key is included in the 20 keystroke maximum. 
     
    Performing the AUX function 
    Press and hold down the AUX key (hold down at least 2 seconds until 4 beeps sound), then enter 
                            The defined function will begin. 
    Your user code 
      
    						
    							– 30 – 
    USER FUNCTIONS
    USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
        
    Clock/Calendar 
     
    Your system can display the current time (see your installer). The date is not displayed, but has an 
    internal function. The system must be disarmed. 
    To set the time and date:
                             +  FUNCTION  +  [63] 
      Master user code or  
     Installer Code 
     
    The system will enter the Voice Prompt Calendar Setting mode. The [#] key can be pressed at 
    any time to repeat a voice prompt. 
     
    NOTES: (1)  Clock-Setting mode automatically ends if no keys are pressed for one minute. 
      (2)  It is not possible to enter the real time clock programming mode from a wireless keypad 
      (3)  Pressing any key on a wireless (RF) keypad terminates Clock/Calendar setup. 
      (4)  It is not possible to enter the real time clock programming mode when either FC or CA is 
    displayed on the display.  
     
    1. “Set Time” will be displayed and the system will announce, “Enter two-digit hour, press ADD to 
    accept, ESCAPE to quit”. 
     
      8:   P 
    Hour PM  
     
    Hour (The current hour will be displayed with the A or P indication.) 
    Enter the 2-digit hour (i.e., 01-12).  
    Press [ADD] to accept the entry and continue to the AM/PM selection. 
    Press [ESCAPE] to exit Clock/Calendar mode (keypad beeps 4 times). 
    2.  The system will announce, “Enter one for PM, zero for AM, press ADD to accept, ESCAPE to quit”. 
     
      8:   P 
    Hour PM  
     
    AM/PM (The AM/PM setting will display A or P.) 
    Enter 1 for PM or 0 for AM. 
    Press [ADD] to accept the entry and continue to the minute selection. 
    Press [ESCAPE] to back up to hour selection. 
    3.  The system will announce, “Enter two-digit minute, press ADD to accept, ESCAPE to quit”. 
     
       : 41 
    Minutes  
     
    Minute (The current minute will display.) 
    Enter the 2-digit minute (i.e., 00-59). 
    Press [ADD] to accept the entry and continue to the month selection. 
    Press [ESCAPE] to back up to AM/PM selection. 
     
     
     
      
    						
    All Honeywell manuals Comments (3)

    Related Manuals for Honeywell control panel LYNX Plus User Manual