Honeywell 8 Channel Dvr Manual

							HREP Color Digital Video Recorder User Guide
Document 800-06847 Rev B31
08/10
Figure 2-9 PTZ Window
2. Select the camera by channel. 
3. Use the arrow buttons to reposition the PTZ camera field of view. 
4. Use ZOOM, FOCUS, and IRIS to change the current camera view.
5. Click PARAMETER to configure PTZ camera parameters. 
See Table 2-1 on page 23 for descriptions of front panel and remote controller controls for 
PTZ cameras. 
Using Digital Zoom
When viewing a channel in full screen, you can use your HREP8 or HREP16 to zoom in to 
a particular area by up to 8 times. The HREP4 supports 2 times digital zoom without a small 
picture-in-picture window. 
Select the desired channel, then navigate to ZOOM   on the control bar, and then 
click . 
Figure 2-10 Example of the Digital Zoom
Select the camera channel
This small window shows the 
full image. For HREP8 and 
HREP16, the main display area 
shows the zoomed portion. 
Click here to escape 
Zoom mode. 
Use these arrows to move 
the zoomed area.  
						

							32 Installation
Viewing the Log
Navigate to LOG   in the control bar, then click   to see the current log. 
A LOG window appears.
Figure 2-11 Log Window
Select a log entry to view the associated video.
Panic Recording
Navigate to REC   in the control bar, then click   to start and stop Panic recording.
The REC button changes to a red square with a “P” to indicate that panic recording has 
started. 
Use the RECORD SETUP window to configure the Panic recording settings. See 
Configuring Panic Recording on page 70.
Using the Quick Menu
Accessing the Quick Menu
Click the right mouse button in any of the live channels to open a Quick menu of options 
for that channel.  
						

							HREP Color Digital Video Recorder User Guide
Document 800-06847 Rev B33
08/10
Figure 2-12 Quick Menu
NoteYou cannot access the Quick Menu if you are in a Display Sequence.
Table 2-3 Quick Menu
Function Description
FREEZE ON/OFFStop or freeze the live display of your selected channel on 
your HREP8 or HREP16; stop or freeze all channels on your 
HREP4. Even though other channels show live display, this 
particular channel display is stopped. Right-click and then 
select FREEZE OFF to exit the freeze mode. 
PTZ See Controlling PTZ Cameras on page 30.
ZOOM See Using Digital Zoom on page 31.
PLAYBACK You can select a go-back duration (10, 
20, or 30 seconds ago, or 1 minute 
ago) or a specific time and date for 
immediate play back.
If you select go to..., the TIME 
SELECTION window appears. 
PANIC REC START See Panic Recording on page 32.
Click OK after selecting your 
desired time.  
						

							34 Installation
System Setup
Navigate to MENU   on the control panel, then click  .
The SETUP window appears.
Figure 2-13 SETUP Window
Click SYSTEM SETUP in the SETUP window.
The MAIN menu window appears. 
Figure 2-14 MAIN Menu Window
Use the cursor keys and   (ENTER) and   (RETURN) to navigate the MAIN setup 
menu.
Use   to select and change a particular item. Use   to cancel a change or exit from a 
particular setup screen.
Select SYSTEM SETUP and then press   to set up all the main system functions. 
Configuring the Camera 
Configuring the Camera Setup
Select CAMERA in the Main system setup window, then click  . The CAMERA setup 
window opens.  
						

							HREP Color Digital Video Recorder User Guide
Document 800-06847 Rev B35
08/10
Figure 2-15 Camera Setup Window
Highlight the camera you want to configure, then press  . You can configure the 
following:
•TITLE: Enter the camera title (maximum 8 characters)
•COVERT: When COVERT is turned ON, the camera image is not displayed in Live 
display, but the DVR continues to record the video. When COVERT is turned ON and 
a Manager or User account is logged on, the live channel does not display in the Web 
Client display. But when an Admin account is logged on, the live channel displays. 
•AUDIO: Choose the audio recording channel. 
Configuring the Color Setup
Click COLOR SETUP on the left side of the CAMERA window. The COLOR SETUP menu 
appears.  
						

							36 Installation
Figure 2-16 COLOR SETUP Menu
You can adjust the brightness, contrast, tint, and color for each channel. Select a channel 
and click   to select that channel for configuration. The selected channel displays full 
screen. 
Figure 2-17 Example of Configuring the Color Setup Window
Click the Up/Down arrows   to configure the brightness, contrast, tint, and color.
Click   when all changes are complete and you want to escape this window. 
						

							HREP Color Digital Video Recorder User Guide
Document 800-06847 Rev B37
08/10
Configuring the PTZ Setup
Click PTZ on the left side of the CAMERA window. The PTZ Setup menu appears. 
Figure 2-18 PTZ SETUP Menu
Click each value in the ADDRESS, PROTOCOL, and BAUD RATE columns to configure 
them. Use the   to change the following values: 
Configuring Details for PTZ Cameras
Click DETAIL on the PTZ SETUP menu. The PTZ Property window appears.
Figure 2-19 PTZ Property Window
ADDRESSThe unique ID of the PTZ device
PROTOCOLThe protocol of the PTZ device
BAUD RATEThe baud rate of the PTZ device
DETAILDetailed settings for the PTZ device. See Configuring 
Details for PTZ Camerasbelow.
TOUR 
						

							38 Installation
Use the   to change the values, then click OK to save the settings. 
NoteSome settings such as AUTO FOCUS might not be compatible with your 
particular PTZ equipment. If this is the case, then changing the value will not 
have an effect on the PTZ control.
Configuring PTZ Presets in Live View
Configure PTZ presets for a preset tour. See Configuring a PTZ Tour on page 39.
1. Navigate to PTZ   in the Control bar, then click   to select. The PTZ window 
appears.
Figure 2-20 PTZ Window
2. Select the camera by channel. 
3. Select a preset number.
4. Use the arrow buttons to reposition the PTZ camera field of view. 
5. Use ZOOM, FOCUS, and IRIS to change the current camera view.
6. Click PARAMETER to configure PTZ camera parameters. 
7. Click SET to save the settings. 
See Table 2-1 on page 23 for descriptions of front panel and remote controller controls for 
PTZ cameras. 
Configuring PTZ Camera Parameters
Click PARAMETER in the PTZ camera window, and the PTZ Parameter window appears. 
Select the camera channel 
						

							HREP Color Digital Video Recorder User Guide
Document 800-06847 Rev B39
08/10
Figure 2-21 PTZ Parameter Window
Configuring a PTZ Tour
You can configure a PTZ tour for each PTZ camera that is connected to the HREP. Before 
you can con figure a PTZ tour, you must configure the presets. See Configuring PTZ Presets 
in Live View on page 38.
1. Click TOUR on the PTZ SETUP menu (see Figure 2-18). The PTZ TOUR window 
appears. 
Figure 2-22 PTZ TOUR Window
2. Click next to MODE to select AUTO to enable PTZ Tour setup.
3. Click on the up/down arrows under the PRESET NO. column to select a preset (from 
1 to 16), then click on the up/down arrows under the DWELL TIME to select a dwell 
time (from 1 to 20 seconds). 
NoteEven though you can configure up to 255 presets using the PTZ menu, for 
configuring a PTZ tour, you can select from only presets numbered 1 - 16.
4. Click OK to save the settings or click CANCEL to exit without saving. 
Configuring the Camera Motion Sensor
Click MOTION SENSOR on the left side of the CAMERA menu. The Motion Sensor menu 
appears. 
						

							40 Installation
Figure 2-23 Motion Sensor Menu
Use the   to change the sensitivity level. The lowest level is 1, and the highest is 10. This 
setting determines the degree of motion required before recording is activated. 
Configuring the Motion Sensor Area
Click the AREA SETUP button next to your desired channel. A grid appears over the video 
image for the chosen channel. 
Figure 2-24 Configuring the Motion Sensor Area
To quickly select or deselect the entire grid, right-click on the screen, then select SELECT 
ALL or DESELECT ALL. 
Configuring the Display
Select DISPLAY in the Main system setup window, and then click  . The DISPLAY 
window appears.