Honeywell 1911ier3 Manual

							Granit 1911i
Industrial Wireless Area-Imaging Scanner
Quick Start Guide
Crdlss-GRNT-QS Rev A 
8/12
Aller à www.honeywellaidc.com pour le français.  
Vai a www.honeywellaidc.com per litaliano.  
Gehe zu www.honeywellaidc.com für Deutsch.  
Ir a www.honeywellaidc.com para español.  
Para Português, acesse www.honeywellaidc.com.br.  
Перейти на русскоязычный сайт www.honeywellaidc.com.  
Pro češtinu jdi na www.honeywellaidc.com.  
Pre slovenčinu choď na www.honeywellaidc.com  
日本語 :  www.honeywellaidc.comをご覧ください。
如要到中国www.honeywellaidc.com（简体）。
查看繁体版请登陆www.honeywellaidc.com
한글  www.honeywellaidc.com로 이동합니다. 
						

							Note: Refer to your user’s guide for information about cleaning your 
device.
For localized language versions of this document, go to www.honeywellaidc.com.
Getting Started
Turn off the computer’s power before connecting the base, then 
power up the computer once the base is fully connected.  When the 
base is connected and powered up, put the scanner in the base to 
establish a link.  The green LED on the base flashes to indicate the 
scanner’s battery is charging.
Power Supply Assembly (if included)
Note: The power supply must be ordered separately, if needed. 
						

							Connecting the Base
USB:   
						

							Keyboard Wedge:
RS232 Serial Port: 
						

							Reading Techniques
The view finder projects an aiming 
beam that should be centered over 
the bar code, but it can be 
positioned in any direction for a 
good read. 
Hold the scanner over the bar code, 
pull the trigger, and center the 
aiming beam on the bar code.
The aiming beam is smaller when 
the scanner is closer to the code 
and larger when it is farther from the 
code.  Hold the scanner close to 
smaller bar codes, and farther away 
from large bar codes to get a proper 
read.  
If the bar code is highly reflective (e.g., laminated), you may need to 
tilt the scanner at an angle so the bar code can be scanned.
Note: If the scanner beeps 3 times when scanning a bar code, the 
link has not been established.  If the scanner beeps once, the 
link has been established.
Standard Product Defaults
The following bar code resets all standard product default settings.
Standard Product Defaults 
						

							USB Serial
Scan the following code to program the scanner to emulate a regular 
RS232-based COM Port.  If you are using a Microsoft® Windows® 
PC, you will need to download a driver from the Honeywell website
 (www.honeywellaidc.com).  The driver will use the next available COM Port number.  Apple® Macintosh computers recognize the 
scanner as a USB CDC class device and automatically use a class 
driver.
Note: No extra configuration (e.g., baud rate) is necessary.
USB PC Keyboard
Scan the following code to program the scanner for a USB PC 
Keyboard.  
USB Serial
USB PC Keyboard 
						

							Keyboard Country
Scan the Program Keyboard Country bar code below, then scan 
the numeric bar code(s) from page 2, then the Save bar code to program the keyboard for your country.  As a general rule, the 
following characters are not supported by the scanner for countries 
other than the United States:
 @  |  $  #  {  }  [  ]  =  /  ‘    <  >  ~.
Note: For a complete list of country codes, see the User’s Guide for 
your product at our website,  www.honeywellaidc.com.
Country CodeScanCountry CodeScan
Belgium1Italy5
Denmark8Norway9
Finland2Spain10
France3Switzerland6
Germany/Austria4USA (Default)0
Great Britain7
Program Keyboard Country 
Save 
						

							Locked Link
If you link a scanner to a base using the Locked Link Mode, other 
scanners are blocked from being linked if they are inadvertently 
placed into the base.  If you do place a different scanner into the 
base, it will charge the scanner, but the scanner will not be linked.
 
To use a different scanner, you need to unlink the original scanner by 
scanning the Unlink Scanner bar code.
Override Locked Scanner
If you need to replace a broken or lost scanner that is linked to a 
base, scan the Override Locked Scanner bar code with a new 
scanner, and place that scanner in the base.  The locked link will be 
overridden; the broken or lost scanner’s link with the base will be 
removed, and the new scanner will be linked.
Unlinking the Scanner
If the base has a scanner linked to it, that scanner must be unlinked 
before a new scanner can be linked.  Once the previous scanner is 
unlinked, it will no longer communicate with the base.  Scan the 
Unlink Scanner bar code to unlink a scanner.
Locked Link Mode
(Single Scanner)
Override Locked Scanner
Unlink Scanner 
						

							Tr i g g e r
The following bar codes will allow you to use the scanner in Manual 
Trigger - Normal Mode (need to press the trigger to read) or 
Presentation mode (the scanner is activated when it “sees” a bar 
code).
Streaming Presentation™
When in Streaming Presentation mode, the scanner leaves the scan 
illumination on all the time and continuously searches for bar codes.
Manual Trigger - Normal
(Default)
Presentation Mode
Streaming Presentation Mode 
						

							Suffix
If you want a carriage return after the bar code, scan the Add CR 
Suffix bar code.  To add a tab after the bar code, scan the Add Tab 
Suffix bar code.  Otherwise, scan the Remove Suffix bar code to 
remove the suffixes.
Add Code ID Prefix to all Symbologies
Scan the following bar code if you wish to add a Code ID prefix to all 
symbologies at once.
Note: For a complete list of Code IDs, see the User’s Guide for your 
product at our website,  www.honeywellaidc.com.
Add CR Suffix
Remove SuffixAdd Tab Suffix
Add Code ID Prefix To All Symbologies
(Temporary)