Honda Vtx 1300 C Owners Manual

102Other Inspections & Lubrication
Clutch System
Servicing Your Honda
Start the engine, pull the clutch lever in,
and shif t into gear. Make sure the
engine does not stall and the motorcycle
does not creep. Gradually release the
clutch lever and open the throttle. Your
motorcycle should move smoothly and
accelerate gradually.
If you cannot get proper adjustment, or the
clutch does not work properly, the cable or
clutch friction discs may be worn. See
your Honda dealer or ref er to the of f icial
Honda...

´
µ
´´µµ (1)
( ) increase
( ) decrease (1) throttle stop screw(())(()) RIGHT SIDE
103 Idle Speed AdjustmentServicing Your Honda
Engine Idle Speed
Saf ety Precautions The best way to assure proper carburetion
is to see your Honda dealer f or regularly
scheduled servicing, including individual
carburetor adjustment and synchronization. Ref er to on page .
Remember, idle speed adjustment is not a
‘‘cure-all’’ f or other problems in your
engine’s f uel-delivery system. Adjusting
the idle will not...

¶ 900 100 rpm
104Servicing Your Honda
Engine Idle Speed
Place your motorcycle on its side stand
on a firm, level surface.
Adjust idle speed with the throttle stop
screw ( ).
Idle speed (in neutral): Connect a tachometer to the engine.
Shif t into neutral. Start the engine. 3.
4. 2.
5.
1
03/03/07 13:14:24 31MEM600_113 

XU20EPR-U (DENSO) DCPR6E (NGK)
DCPR7E (NGK)
XU22EPR-U (DENSO)or
or standard
spark plug
for
extended
high speed
riding
105 Spark Plug Recommendation
Spark Plugs
Servicing Your Honda
Using spark plugs with an improper heat
range can cause engine damage. Use only the recommended type of spark
plugs in the recommended heat range.
03/03/07 13:14:32 31MEM600_114 

RIGHT SIDE
(1)
(1) over head cover(2)
(3)
(2) spark plug caps
(3) spark plug wrench
106Spark Plug Replacement &
Inspection
Spark Plugs
Servicing Your Honda
Saf ety PrecautionsClean any dirt f rom around the spark
plug bases.
Disconnect the spark plug caps ( ).
Take care to avoid damaging the spark
plug wire when disconnecting the caps. Refer to on page .
Usingthesparkplugwrench( )
provided in the tool kit, remove the
spark plugs. Grasp the over head covers ( ) on both
side and pull out. 1.
2.
3.
4. 56 2...

µµ 0.031 0.035 in (0.80 0.90 mm)
(1)(2)
(1) spark plug gap (2) side electrode
107
Spark Plugs
Servicing Your Honda
Inspect the electrodes and center
porcelain f or deposits, corrosion, or
carbon f ouling. If the corrosion or
deposits are heavy, replace the plug.
Clean a carbon or wet-f ouled plug with
a plug cleaner, if available, or a wire
brush.
Check the spark plug gap ( ) of each
new plug, using a wire-type f eeler
gauge. If adjustment is necessary, bend
the side electrode ( ) caref ully.
The gap...

108
Spark Plugs
Servicing Your Honda
Improperly tightened spark plugs can
damage the engine. If a plug is too loose,
a piston may be damaged. If a plug is too
tight, the threads may be damaged.Tighten each spark plug:
1/8-1/4 turn af ter it seats (if the old
plug is good)
1/2 turn after it seats (if installing a
new plug)
Reinstall the spark plug caps. Take care
to avoid pinching any cables or wires.
Reinstall the over head covers (page
). 8.
9.
10.
106
03/03/07 13:14:58 31MEM600_117 

109
Suspension
Servicing Your Honda
The way you ride your motorcycle and the
type of ride you want to experience can
also inf luence your suspension needs. Your f ront and rear suspension systems
use springs and hydraulic damping devices
that suspend your weight and most of the
weight of your motorcycle.
The spring pre-load f or your rear
suspension system adjusts the amount of
f orce required to begin compression of the
spring.
The oil damper systems hydraulically
control the natural compression and...

LEFT SIDE
(1)(2)
(1) pin spanner
(2) shock absorber
110Rear Suspension Adjustment Rear Suspension Spring Pre-load
Suspension
Servicing Your Honda
Saf ety Precautions The rear suspension can be adjusted for
rider (and passenger) weight and riding
conditions by changing the spring pre-load.
Do not attempt to disassemble, service, or
dispose of the damper; see your Honda
dealer. The instructions f ound in this
owner’s manual are limited to adjustments
of the shock assembly only.Refer to on page .56
03/03/07...

111
Suspension
Servicing Your Honda
The spring pre-load adjuster has
positions f or dif f erent load or riding
conditions.Make sure that both shock absorbers are
adjusted to the same position.
Always adjust the shock absorber position
in sequence (1-2-3-4-5 or 5-4-3-2-1).
Attempting to adjust directly f rom 1 to 5
or 5 to 1 may damage the shock absorber. Use the pin spanner ( ) to adjust the rear
shock spring pre-load.
Position 1: f or a light load and smooth
road conditions.
Position 2: standard...