honda nc700 s sa sd owners 2012 User Manual

							Removing & Installing Body Components u Clip
68
Maintenance
Clip
The clip must be removed to open the 
owner’s manual box.
❙Removal
1.Press down on the centre pin to release 
the lock.
2.Pull the clip out of the hole.
❙Installation
1.Slightly open the retaining pawls and then 
push them out.
2.Insert the clip into the hole.
3.Lightly press down on the centre pin to 
lock the clip.
!a
!b
!a
!b !c
12 NC700S (NM-1)-32MGS600.book  68 ページ  ２０１２年４月１８日　水曜日　午後６時１７分 
						

							Removing & Installing Body Components u Battery
69
Maintenance
Battery❙Removal
Make sure the ignition switch is off.
1.Open the luggage box. 2P. 44
2.Remove the maintenance lid. 2P. 65
3.Unhook the rubber strap.
4.Disconnect the negative - terminal from 
the battery.
5.Disconnect the positive + terminal from 
the battery.
6.Remove the battery taking care not to 
drop the terminal nuts.
❙Installation
Install the parts in the reverse order of 
removal. Always connect the positive 
+ 
terminal first. Make sure that bolts and nuts 
are tight.
The clock will be reset  AM 1:00 if the battery 
is disconnected.
For proper handling of the battery, see 
“Maintenance Fundamentals.” 
2P. 55
Battery Goes Dead 
2P. 107
Battery Rubber strap
Positive 
terminal
Negative 
terminal
12 NC700S (NM-1)-32MGS600.book  69 ページ  ２０１２年４月１８日　水曜日　午後６時１７分 
						

							70
Maintenance
Engine Oil
Checking the Engine Oil
1.If the engine is cold, idle the engine for 3 
to 5 minutes.
2.Turn the ignition switch off, stop the 
engine and wait for 2 to 3 minutes.
3.Place your motorcycle in an upright 
position on a firm, level surface.
4.Remove the oil fill cap/dipstick and wipe it 
clean.
5.Insert the oil fill cap/dipstick until it seats, 
but don’t screw it in.
Check that the oil level is between the 
upper and lower level marks in the oil fill 
cap/dipstick.
6.Securely install the oil fill cap/dipstick. (NC700S/SA)
Oil fill cap/dipstick
Upper 
level
Lower level
12 NC700S (NM-1)-32MGS600.book  70 ページ  ２０１２年４月１８日　水曜日　午後６時１７分 
						

							Engine Oil u Adding Engine Oil
71
Maintenance
(NC700SD)
Adding Engine Oil
If the engine oil is below or near the lower 
level mark, add the reco mmended engine oil. 
2P. 57
1.Add the recommended oil until it reaches 
the upper level mark.
uPlace your motorcyc le in an upright 
position on a firm, level surface when 
checking the oil level. u
Do not overfill above the upper level 
mark.
u Make sure no foreign objects enter the 
oil filler opening.
u Wipe up any spills immediately.
2.Securely reinstall the oil fill cap/dipstick.
For the recommended oil and oil selection 
guidelines, see “Maintenance 
Fundamentals.” 
2P. 57
Upper 
level
Lower 
level
Oil fill cap/dipstick
NOTICE
Overfilling with oil or operating with insufficient oil can 
cause damage to your engine. Do not mix different brands 
and grades of oil. They may  affect lubrication and clutch 
operation.
12 NC700S (NM-1)-32MGS600.book  71 ページ  ２０１２年４月１８日　水曜日　午後６時１７分 
						

							Engine Oil u Changing Engine Oil & Filter
72
Maintenance
Changing Engine Oil & Filter
Changing the oil and filter requires special 
tools. We recommend that you have your 
motorcycle serviced by your dealer.
Use a new Honda Genuine oil filter or 
equivalent specified for your model.
1.Remove the lower cowl. 2P. 66
2.If the engine is cold, idle the engine for 3 
to 5 minutes.
3.Turn the ignition sw itch off, stop the 
engine and wait for 2 to 3 minutes.
4.Park on a firm, level surface and lower 
the side stand.
5.Place a drain pan under the drain bolt.
6.Remove the oil fill cap/dipstick, drain 
bolt, and sealing washer to drain the oil.
7.Remove the oil filter with a filter wrench 
and let the remaining oil drain out. Make 
sure the prior seal is not stuck to the 
engine. u Discard the oil and oil filter at an 
approved recycling centre.
NOTICE
Using the wrong oil filter can  result in serious damage to 
the engine.Sealing washer Drain bolt
12 NC700S (NM-1)-32MGS600.book  72 ページ  ２０１２年４月１８日　水曜日　午後６時１７分 
						

							Engine Oil u Changing Engine Oil & Filter
73
Maintenance
8.Apply a thin coat of engine oil to the 
rubber seal of a new oil filter.
9.Install a new oil filter and tighten.
10.Install a new sealing washer onto the 
drain bolt. Tighten the drain bolt.
11.Fill the crankcase with the recommended 
oil (
2P. 57) and install the oil fill cap/
dipstick.
12.Check the oil level. 2P. 70
13.Check that there are no oil leaks.
14.Install the lower cowl.
Torque: 
26 N·m (2.7 kgf·m, 19 lbf·ft).
Torque:  30 N·m (3.1 kgf·m, 22 lbf·ft).
Oil filter Rubber seal
Required oil
NC700S/SA
When changing oil & 
engine oil filter:
3.4 litres (3.6 US qt, 3.0 Imp qt)
When changing oil only:
3.1 litres (3.3 US qt, 2.7 Imp qt)
NC700SD When changing oil & 
engine oil filter:
3.4 litres (3.6 US qt, 3.0 Imp qt)
When changing oil only:
3.2 litres (3.4 US qt, 2.8 Imp qt)
12 NC700S (NM-1)-32MGS600.book  73 ページ  ２０１２年４月１８日　水曜日　午後６時１７分 
						

							Engine Oil u Changing Clutch Oil Filter (NC700SD only)
74
Maintenance
Changing Clutch Oil Filter 
(NC700SD only)
Use a new Honda Genuine  clutch oil filter or 
equivalent specified for your model.
1.Follow the steps 1-7 of Changing Engine 
Oil & Filter. 
2P. 72
2.Remove the clutch oil filter cover, clutch 
oil filter and spring by removing the 
clutch oil filter cover bolts. u Discard the oil and cl utch oil filter at 
an approved recycling centre.
NOTICE
Using the wrong clutch oil fi lter can result in serious 
damage to the transmission.
OUT-SIDE 
mark
Clutch 
oil filter
Rubber 
seal
Clutch oil 
filter cover
boltsO-ring Spring
12 NC700S (NM-1)-32MGS600.book  74 ページ  ２０１２年４月１８日　水曜日　午後６時１７分 
						

							Engine Oil u Changing Clutch Oil Filter (NC700SD only)
75
Maintenance
3.Install the new clutch  oil filter with the 
rubber seal facing in, toward the engine. 
You will see “OUT-SIDE” mark on the 
clutch oil filter body, toward the filter 
cover.
4.Replace the O-ring and apply a thin coat 
of engine oil to the new O-ring when 
before installing it.
5.Install the spring and the clutch oil filter 
cover.
6.Install the clutch oil filter cover bolts and 
tighten.
7.Apply a thin coat of engine oil to the 
rubber seal of a new engine oil filter. 
2P. 73
8.Install a new engine oil filter and tighten.
9.Install a new sealing washer onto the 
drain bolt. Tighten the drain bolt.
10.Fill the crankcase with the recommended 
oil (
2P. 57) and install the oil fill cap/
dipstick.
11.Check the oil level. 2P. 70
12.Check that there are no oil leaks.
13.Install the lower cowl.
Torque:  26 N·m (2.7 kgf·m, 19 lbf·ft).
Torque: 30 N·m (3.1 kgf·m, 22 lbf·ft).
Required oil
When changing oil, engine oil 
filter & clutch oil filter:
3.4 litres (3.6 US qt, 3.0 Imp qt)
12 NC700S (NM-1)-32MGS600.book  75 ページ  ２０１２年４月１８日　水曜日　午後６時１７分 
						

							76
Maintenance
Coolant
Checking the Coolant
1.Place your motorcycle on a firm, level 
surface.
2.Hold your motorcycle in an upright 
position.
3.Check that the coolant level is between 
the UPPER and LOWER level marks in the 
reserve tank.If the coolant level is dropping noticeably or 
the reserve tank is empty, you likely have a 
serious leak. Have your motorcycle inspected 
by your dealer.Adding Coolant
1.If the coolant level is below the LOWER 
level, add the recommended coolant 
(
2P. 59) until the level reaches the UPPER 
level mark.
Add fluid only from the reserve tank cap 
and do not remove radiator cap.
2.Remove the lower cowl. 2P. 66
Reserve tank
UPPER level
LOWER level
12 NC700S (NM-1)-32MGS600.book  76 ページ  ２０１２年４月１８日　水曜日　午後６時１７分 
						

							Coolant u Changing Coolant
77
Maintenance
3.Remove the reserve tank cap and add 
fluid while monitoring the coolant level.
uDo not overfill above the UPPER level 
mark.
u Make sure no forei gn objects enter the 
reserve tank opening.
4.Securely reinstall the cap.
5.Install the lower cowl.
Changing Coolant
Have your dealer change the coolant unless 
you have the proper tools and are 
mechanically qualified.
3WARNING
Removing the radiator cap while the 
engine is hot can cause the coolant to 
spray out, potentia lly scalding you.
Always let the engine and radiator 
cool down before removing the 
radiator cap.
Reserve tank cap
12 NC700S (NM-1)-32MGS600.book  77 ページ  ２０１２年４月１８日　水曜日　午後６時１７分