Honda H R B 215 Manual
Here you can view all the pages of manual Honda H R B 215 Manual. The Honda manuals for Lawn Mower are available online for free. You can easily download all the documents as PDF.
Page 41
9. MAINTENANCE Periodic maintenance and adjustment are necessary to keep the mower in good operating condition. Service and inspect according to the MAINTENANCE SCHEDULE. l To avoid carbon monoxide poisoning, shut the engine off before performing any maintenance. l To avoid serious bums, let the engine cool for at least 15 minutes before performing maintenance. Use genuine Honda parts or their equivalent for maintenance and repair. Parts of lower quality may damage the mower. Maintenance...
Page 42
ENGINE OIL CHANGE Engine oil capacity: 0.63 US qt (0.6 PI Drain the oil while the engine is warm to assure rapid and complete draining. 1. Place a suitable container under the cutter deck to catch the used oil. NOTE: Check to be sure the drain hole in the cutter deck is not clogged. If necessary, remove grass and debris from the cutter deck. 2. Remove the oil filler cap and the oil drain bolt, using a 10 mm box or socket wrench. The used oil will flow along the cutter deck channel to the drain...
Page 43
9. MAINTENANCE 3. 4. 5. 6. Install the oil drain bolt and tighten it securely. Fill with the recommended oil (see page 22) to the upper level on the dipstick. Do not overfill. Install the filler cap/dipstick. Wipe the cutter deck drain channel clean to reduce dirt build-up when the mower is used. NOTE: Used motor oil may cause skin cancer if repeatedly left in contact with the skin for prolonged periods. Although this is unlikely, unless you handle used oil on a daily basis, it is still...
Page 44
9. MAINTENANCE AIR CLEANER SERVICE A dirty air filter will restrict air flow to the carburetor, reducing engine performance If you operate the mower in very dusty areas, clean the air filter more often than specified in the MAINTENANCE SCHEDULE. 3 r7iEEq Operating the engine with no air filter, or a damaged air filter, will cause rapid engine wear. 1. Remove the two cover screws, then remove the air cleaner cover. Remove the air filter, and separate the filter elements. Carefully check both...
Page 45
9. MAINTENANCE COVER scmvs~~ AIR CLEANER / COVER SING // ‘ A AIR FILTER PAPER ELEMENT AIR FILTER FOAM ELEMENT AIR CLEANER 43
Page 46
9. MAINTENANCE SPARK PLUG SERVICE Recommended spark plugs: NGK BPR5ES ND 16EPR-U CHAMPION RN12Y r--ziEg Spark plugs of the wrong heat range can cause engine damage. For good performance, the spark plug must be properly gapped and free of deposits. 1. Disconnect the spark plug cap, and remove any dirt from around the spark plug area. B Touching the engine or exhaust system while hot can cause bums. Let the engine cool before servicing. 2. Remove the spark plug with a spark plug wrench. 3....
Page 47
9. MAINTENANCE SPARK ARRESTER MAINTENANCE (optional equipment) The spark arrester must be serviced every 100 hours to keep it functioning as designed. B Touching the engine or exhaust system while hot can cause bums. Let the engine cool before servicing. 1. Remove the two nuts from the muffler shield, using a 10 mm wrench. 2. Remove the muffler shield, identification plate, muffler, and gasket. 3. Remove the spark arrester from the muffler. 4. Check for carbon deposits on the spark arrester and...
Page 48
9. MAINTENANCE RDTO-STDP CABLE ADJUSTMENT 1. Measure free play at the tip of the lever, while holding the button down. Free play should be 3/4-l in (20-25 mm). 2. If adjustment is necessary, loosen the lock nuts with a 10 mm wrench, and move the adjuster up or down as required. Tighten the lock nuts and recheck free play. NOTE: When mowing, check that the ROTO-STOP lever operates properly. If the blade does not start or stop as it should, and lever free play is correctly adjusted, take the mower...
Page 49
9. MAINTENANCE HR215SXA & HR215SMA DRIVE CLUTCH CABLE ADJUSTMENT 1. Measure free play at the top of the lever, as shown. Free play should be 3/16-3/8 in (5-10 mm). 2. If adjustment is necessary, loosen the lock nuts with a 10 mm wrench, and move the adjuster up or down as required. Tighten the lock nuts and recheck free play. 3. Start the engine and operate the drive clutch lever. Check to be sure the drive clutch engages and releases properly. If the drive clutch does not operate properly, and...
Page 50
9. MAINTENANCE HR215HXA DRIVE CLUTCH CABLE ADJUSTMENT _ 1. 2. 3. Remove the bolt from the transmission cover, using an 8 mm socket wrench. Remove the transmission cover. TRANSMISSION Move the gear shift lever all the way back to the slowest position. SHIFT LEVER Push the diive clutch lever all the way forward, and hold it against the handlebar. 48