Honda Crf250l Service Manual

16-18
dummyhead
dummyhead
FRONT WHEEL/SUSPENSION/STEERING
– Screws [1]
– Right handlebar switch [2]
– Screws [1]
– Throttle housing cover [2]
– Bolts [1]
– Handlebar upper holders [2]
– Handlebar [3]
Pull out the handlebar [1] from the throttle pipe [2].
Remove the following:
– Throttle cables [3]
– Throttle pipe
– Throttle housing [4] 
[2][1]
[2]
[1]
[2]
[3][1]
[2]
[3]
[1]
[4] 

16-19
dummyhead
dummyhead
FRONT WHEEL/SUSPENSION/STEERING
INSTALLATION
Apply grease to the cable rolling area of the throttle pipe
[1] flange.
Connect the throttle cables [2] to the throttle pipe.
Insert the handlebar [3] into the throttle pipe.
Align the punch mark on the
handlebar with the top edge of the
lower holder.Install the handlebar and upper holders [1] with the
punch marks [2] facing forward.
Install the bolts [3], tighten the front bolts first, then
tighten the rear bolts securely.
Install...

16-20
dummyhead
dummyhead
FRONT WHEEL/SUSPENSION/STEERING
Install and tighten the upper screw [1] first, then tighten
the lower screw [2] to the specified torque.
If the left handlebar grip [1] was removed, apply Honda
Bond A or equivalent to the inside surface of the grip
and to the clean surface of the handlebar.
Wait 3 – 5 minutes and install the grip. Rotate the grip
for even application of the adhesive.
Position the handlebar grip so that the projection [2] of
the grip is aligned with  the punch...

16-21
dummyhead
dummyhead
FRONT WHEEL/SUSPENSION/STEERING
Align the edge of
the master cylinder
with the punchmark on thehandlebar.Install the brake master cy linder [1] and holder [2] with
the UP mark [3] facing up.
Install the bolts [4] and tighten the upper bolt first, then
tighten the lower bolt to the specified torque.
Connect the brake light switch connectors [5]. 
Align the edge of
the bracket with the punch mark on the handlebar.Install the clutch lever bracket [1] and holder [2].
Install the...

16-22
dummyhead
dummyhead
FRONT WHEEL/SUSPENSION/STEERING
Remove the bolt [1] and brake hose guide [2].
Remove the steering stem cap [1].
Loosen the steering stem nut [2].
Remove the fork legs (page 16-6).
Remove the stem nut, washer [3] and top bridge [4].
Loosen the steering stem adjusting nut [1] using the
special tool.
While holding the steering stem, remove the adjusting
nut.
Remove the following:
– Upper dust seal [1]
– Upper steering bearing [2]
– Steering stem [3]
Inspect the bearings and outer...

16-23
dummyhead
dummyhead
FRONT WHEEL/SUSPENSION/STEERING
BEARING REPLACEMENT
Always replace the
bearings and races
as a set.Remove the upper and lower bearing outer races [1]
using the special tools.
Install the stem nut [1] ont o the stem to prevent the
threads from being damaged when removing the lower
bearing [2].
Remove the lower bearing and lower dust seal [3] with
a chisel or equivalent tool, being careful not to damage
the stem.
Apply specified grease (page 16-24) to a new lower
dust seal [1] lip...

16-24
dummyhead
dummyhead
FRONT WHEEL/SUSPENSION/STEERINGINSTALLATION
Apply 3 - 5 g (0.11 - 0.18 oz) of specified grease (Urea
based multi-purpose grease with extreme pressure
agent (example: Kyodo  Yushi, EXCELITE EP2 or
equivalent) to each new bearing and fill it up.
Apply specified grease to a new upper dust seal [1] lip.
Insert the steering stem [2] into the steering head pipe,
and install the following while holding the stem.
– upper steering bearing [3]
– upper dust seal
Apply engine oil to the...

16-25
dummyhead
dummyhead
FRONT WHEEL/SUSPENSION/STEERING
Turn the steering stem [1] right and left, lock-to-lock
several times to seat the bearings.
Completely loosen the adjusting nut [2].
Retighten the adjusting nut [1] to the specified torque
using the special tool.
Install the top bridge [1], washer [2] and stem nut [3].
Temporarily install the outer tube into the bottom and
top bridges.
Tighten the stem nut to the specified torque.
Make sure the steering st em moves smoothly without
play or...

16-26
dummyhead
dummyhead
FRONT WHEEL/SUSPENSION/STEERING
Install brake hose guide [1] and tighten the bolt [2] to
the specified torque.
Install the meter stay [1] and tighten the bolts [2].
Secure the ignition switch wire with the harness bands
[3].
Connect the ignition switch 3P (Brown) connector [4].
Install the following:
– Front wheel (page 16-4)
– Handlebar (page 16-19)
– Headlight cowl (page 2-5)
– Front fender (page 2-5)
STEERING BEARING PRE-LOAD
Raise the front wheel off the ground by placing a...

17-1
17
dummytext
17. REAR WHEEL/SUSPENSION
SERVICE INFORMATION ···························17-2
TROUBLESHOOTING·································17-2
COMPONENT LOCATION ··························17-3
REAR WHEEL ·············································17-4SHOCK ABSORBER ·································· 17-6
SHOCK LINKAGE····················\
··················\
· 17-7
SWINGARM ·············································· 17-10
DRIVE CHAIN GUIDE ······························· 17-12