Hitachi Projector Cp X605 Users Manual

							21
Operating
Using the magnify feature
1.Press the ON button of MAGNIFY on the remote control.  
The “MAGNIFY” indication will appear on the screen 
(although the indication will disappear in several seconds with 
no operation), and the projector will go into the MAGNIFY 
mode.
2.8VHWKHFXUVRUEXWWRQV
x
zWRDGMXVWWKH]RRPOHYHO
To move the zoom area, press the POSITION button in the MAGNIFY mode, 
WKHQXVHWKHFXUVRUEXWWRQV
x
z
{
yWRPRYHWKHDUHD$QGWR
						

							22
Operating
Temporarily blanking the screen
1.Press the BLANK button on the remote control. 
The blank screen will be displayed instead of the screen 
of input signal. Please refer to the BLANK item in SCREEN 
menu
(	38).
To exit from the blank screen and return to the input signal screen, press the 
BLANK button again. 


						

							23
Operating
Using the menu function
This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, AUDIO, 
SCREEN, OPTION, NETWORK, and EASY MENU. EASY MENU consists of functions 
(DFKRIWKHVHPHQXVLV
operated using the same methods. The basic operations of these menus are as follows.
1.Press the MENU button on the remote control or one of 
the cursor buttons on the projector.  
The Advanced MENU, or EASY MENU that has priority just 
after powered on, will appear. 
In the EASY MENU
2.If you want to change it to the Advanced MENU, select the 
"Go to Advanced Menu..."
3.8VHWKHFXUVRUEXWWRQV
x
zWRVHOHFWDQLWHPWRRSHUDWH
4.8VHWKHFXUVRUEXWWRQV
{
yWRRSHUDWHWKHLWHP
In the Advanced MENU
2.8VHWKHFXUVRUEXWWRQV
x
zWRVHOHFWDPHQX
If you want to change it to the EASY MENU, select the 
EASY MENU.

control, or the ENTER button on the remote control to select 
an item. The display of the selected menu will be active.
3.8VHWKHFXUVRUEXWWRQV
x
zWRVHOHFWDQLWHPWRRSHUDWH
Then press the cursor button 
y on the projector or remote control, or the ENTER button 
on the remote control to progress. The operation menu of the selected item will appear.
4.8VHWKHFXUVRUEXWWRQV
x
zWRRSHUDWHWKHLWHP

”
When you want to reset the operation, press the RESET button on the remote control 
during the operation. Note that items whose functions are performed simultaneously 
with operation (ex. LANGUAGE, H PHASE, VOLUME etc.) cannot be reset.

”In the Advanced MENU, when you want to return to the previous display, press the 
cursor button 

{ on the projector or remote control, or the ESC button on the remote 
control.
5.Press the MENU button on the remote control again to close the menu 
and complete this operation. Even if you do not do anything, the dialog will 
automatically disappear after about 10 seconds.
LVVHOHFWHGRU
when a certain input signal is displayed.
#5;/07=4)$?
#52%6




 :%76




)QVQ#FXCPEGF/GPW

014/#.
014/#.
014/#.
J
0).+5* #761-;5610
-;5610
-;5610
2+%674/1&
$4+)*6055
%1064#56
%1.14
6+06
5*#42055
9*+524
/+4414
456
(+.646+/
.#0)7#)


/07=4)$?
+/#)

5672

#7&+1
2+%674

+0276

126+10 5%40
5*#42055
 $4+)*60559×
%1064#569×
%1.149×
6+069× %1.146/2
/+& )#//#
&(#7.6


5.%6

06914-
#5;/07#%6+8+4+567401((
/;//14;5#8
RESET button ENTER button
MENU button Cursor buttons
ASPECT
ESC MENU RESET
POSITION AUTO
PUSH ENTER
PAGE UP PAGE DOWN 
						

							24
EASY Menu
EASY Menu
Item Description
ASPECT8VLQJWKH
{
yEXWWRQVVZLWFKHVWKHPRGHIRUDVSHFWUDWLR
See the ASPECT item in IMAGE menu (
	29).
AUTO 
KEYSTONE 
EXECUTESee the AUTO KEYSTONE  EXECUTE item in SETUP menu(	35).
KEYSTONE 
8VLQJWKH
{
See the KEYSTONE 
 item in SETUP menu (	35).
KEYSTONE 
8VLQJWKH
{
See the KEYSTONE 
 item in SETUP menu (	35).
 PICTURE MODE8VLQJWKH
{
yEXWWRQVVZLWFKHVWKHSLFWXUHPRGH
The picture modes are combinations of GAMMA and COLOR 
TEMP settings. Choose a suitable mode according to the projected 
source.
               NORMAL 
Ù CINEMA 
Ù DYNAMIC 
  WHITEBOARD 
Ù BOARD(GREEN) 
Ù BOARD(BLACK)
COLOR TEMP GAMMA
NORMAL MID DEFAULT #1 DEFAULT
CINEMA LOW DEFAULT #2 DEFAULT
DYNAMIC HIGH DEFAULT #3 DEFAULT
BOARD(BLACK) Hi-BRIGHT-1 DEFAULT #4 DEFAULT
BOARD(GREEN) Hi-BRIGHT-2 DEFAULT #4 DEFAULT
WHITEBOARD MID DEFAULT #5 DEFAULT
• When the combination of GAMMA and COLOR TEMP differs 
from pre-assigned modes above, the display on the menu for the 
PICTURE MODE is “CUSTOM”. Please refer to the GAMMA (
	26)
and COLOR TEMP (
	27) items in PICTURE menu.
•
When this function is performed, a certain extra such as a line may appear.
From the EASY MENU, items shown in the table below can 
be performed. 
Select an item using the
x
z cursor buttons on the 
projector or remote control. Then perform it according to the 
following table. 
#5;/07=4)$?
#52%6




 :%76




)QVQ#FXCPEGF/GPW

014/#.
014/#.
014/#.
J
0).+5* #761-;5610
-;5610
-;5610
2+%674/1&
$4+)*6055
%1064#56
%1.14
6+06
5*#42055
9*+524
/+4414
456
(+.646+/
.#0)7#)


(continued on next page) 
						

							25
EASY Menu
Item Description
BRIGHTNESS8VLQJWKH
{
yEXWWRQVDGMXVWVWKHEULJKWQHVV
See the BRIGHTNESS item in PICTURE menu (
	26).
CONTRAST
8VLQJWKH
{
yEXWWRQVDGMXVWVWKHFRQWUDVW
See the CONTRAST item in PICTURE menu
(	26).
COLOR8VLQJWKH
{
yEXWWRQVDGMXVWVWKHVWUHQJWKRIZKROHFRORU
See the COLOR item in PICTURE menu (
	27).
TINT8VLQJWKH
{
yEXWWRQVDGMXVWVWKHWLQW
See the TINT item in PICTURE menu (
	27).
SHARPNESS
8VLQJWKH
{
yEXWWRQVDGMXVWVWKHVKDUSQHVV
See the SHARPNESS item in PICTURE menu
(	27).
WHISPER8VLQJWKH
{
yEXWWRQVWXUQVRIIRQWKHZKLVSHUPRGH
See the WHISPER item in SETUP menu (
	36).
MIRROR8VLQJWKH
{
yEXWWRQVVZLWFKHVWKHPRGHIRUPLUURUVWDWXV
See the MIRROR item in SETUP menu (
	36).
RESETPerforming this item resets all of the EASY MENU items except the 
FILTER TIME and LANGUAGE.
$XVLQJ
WKH
xEXWWRQSHUIRUPVUHVHWWLQJ
FILTER TIMELPH
RIWKHDLU
						

							26
PICTURE Menu
PICTURE Menu
Item Description
BRIGHTNESS8VLQJWKH
x
zEXWWRQVDGMXVWVWKHEULJKWQHVV
Light
Ù Dark
CONTRAST8VLQJWKH
x
zEXWWRQVDGMXVWVWKHFRQWUDVW
Strong
Ù Weak
GAMMA8VLQJWKH
x
zEXWWRQVVZLWFKHVWKHJDPPDPRGH
 #1 DEFAULT 
Ù#1 CUSTOM 
Ù #2 DEFAULT 
Ù #2 CUSTOM 
Ù #3 DEFAULT 
#5 CUSTOM 
Ù #5 DEFAULT 
Ù #4 CUSTOM 
Ù #4 DEFAULT 
Ù #3 CUSTOM
To adjust CUSTOM
Selecting a mode whose name includes 
&86720DQGWKHQSUHVVLQJWKH
yEXWWRQ
or the ENTER button displays a dialog to aid 
you in adjusting the mode.
This function is useful when you want to 
change the brightness of particular tones.
&KRRVHDQLWHPXVLQJWKH
{
yEXWWRQVDQG
DGMXVWWKHOHYHOXVLQJWKH
x
zEXWWRQV
You can display a test pattern for checking the effect of your 
adjustment by pressing the ENTER button.
Each time you press the ENTER button, the pattern changes as 
below.
  No pattern 
Ö Gray scale of 9 steps 
                 Ramp 
Õ Gray scale of 15 steps
The eight equalizing bars correspond to eight tone levels of the test 
pattern except the darkest in the left end. If you want to adjust the 
2nd tone from left end on the test pattern (Gray scale of 9 steps), 
use the equalizing adjustment bar “1”. The darkest tone at the left 
end of the test pattern cannot be controlled with any of equalizing 
adjustment bar.
• When this function is performed, lines or other distortion may 
appear.
From the PICTURE menu, items shown in the table below 
can be performed. 
Select an item using the
x
z cursor buttons on the 
projector or remote control, and press the
y cursor button 
on the projector or remote control, or the ENTER button 
on the remote control to execute the item. Then perform it 
according to the following table.
1
+02
+03
+04
+05
+06
+07
+08
+0
GAMMA [
CUSTOM 1]
ENTER : 
/07=4)$?
+/#)

5672

#7&+1
2+%674

+0276

126+10 5%40
5*#42055
 $4+)*60559×
%1064#569×
%1.149×
6+069× %1.146/2
/+& )#//#
&(#7.6


5.%6

06914-
#5;/07#%6+8+4+567401((
/;//14;5#8
(continued on next page) 
						

							27
Item Description
COLOR TEMP8VLQJWKH
x
zEXWWRQVVZLWFKHVWKHFRORUWHPSHUDWXUHPRGH
To adjust CUSTOM
Selecting a mode whose name includes 
&86720DQGWKHQSUHVVLQJWKH
yEXWWRQRUWKH
ENTER button displays a dialog to aid you in 
adjusting the OFFSET and GAIN of the selected 
mode.
OFFSET adjustments change the color intensity 
on the whole tones of the test pattern.
GAIN adjustments mainly affect color intensity 
on the brighter tones of the test pattern.
&KRRVHDQLWHPXVLQJWKH
{
yEXWWRQVDQGDGMXVWWKHOHYHOXVLQJ
WKH
x
zEXWWRQV
You can display a test pattern for checking the effect of your 
adjustment by pressing the ENTER button. 
Each time you press the ENTER button, the pattern changes as 
below.
  No pattern 
Ö Gray scale of 9 steps 
                 Ramp 
Õ Gray scale of 15 steps
• When this function is performed, lines or other distortion may 
appear.
COLOR8VLQJWKH
x
zEXWWRQVDGMXVWVWKHVWUHQJWKRIZKROHFRORU
Strong
Ù Weak
• This item can be selected only for a video signal, s-video or 
component video signal.
TINT8VLQJWKH
x
zEXWWRQVDGMXVWVWKHWLQW
Greenish
Ù Reddish
• This item can be selected only for a video signal, s-video or 
component video signal.
SHARPNESS8VLQJWKH
x
zEXWWRQVDGMXVWVWKHVKDUSQHVV
Strong
Ù Weak
•7KHUHPD\EHVRPHQRLVHDQGRUWKHVFUHHQPD\ÀLFNHUIRUD
moment when an adjustment is made. This is not a malfunction.
PICTURE Menu
PICTURE Menu (continued)
R
+0
G
+0
B
+0
COLOR TEMP [CUSTOM-1]
ENTER : 
OFFSETR
+0
G
+0
B
+0
GAIN
HIGH DEFAULT 

 HIGH CUSTOM

 MID DEFAULT 

 MID CUSTOM
LOW DEFAULT
LOW CUSTOM
Hi-BRIGHT-1 DEFAULT
Hi-BRIGHT-1 CUSTOM
Hi-BRIGHT-2 DEFAULT 

 Hi-BRIGHT-2 CUSTOM 
(continued on next page) 
						

							28
PICTURE Menu
Item Description
ACTIVE IRIS8VLQJWKH
x
PRESENTATION  
Ù  THEATER  
Ù  TURN OFF
Feature
PRESENTATIONThe active iris displays the best presentation 
image for both bright and dark scenes.
THEATERThe active iris displays the best theater image for 
both bright and dark scenes.
TURN OFF The active iris is always open.
•7KHVFUHHQPD\
						

							29
IMAGE Menu
IMAGE Menu
Item Description
ASPECT8VLQJWKH
x
zEXWWRQVVZLWFKHVWKHPRGHIRUDVSHFWUDWLR
For an RGB signal
NORMAL 
Ù 4:3 
Ù16:9
Ù SMALL
For an M1-D signal
NORMAL 
Ù 4:3 
Ù16:9
Ù14:9
Ù SMALL
For a Video signal, S-video signal or Component video signal
4:3
Ù16:9
Ù14:9
Ù SMALL
For no signal
¿[HG
• The NORMAL mode keeps the original aspect ratio of the signal.
OVER SCAN8VLQJWKH
x
zEXWWRQVDGMXVWVWKHRYHUVFDQUDWLR
Large (It reduces picture) 
Ù6PDOO,WPDJQL¿HVSLFWXUH
•
This item can be selected only for a video, s-video and component signal.
• When this adjustment is too large, certain degradation may appear 
at the frame area of the picture. In such a case, please adjust small.
V POSITION8VLQJWKH
x
zEXWWRQVDGMXVWVWKHYHUWLFDOSRVLWLRQ
Up
Ù Down
• Over-adjusting the vertical position may cause noise to appear 
on the screen. If this occurs please reset the vertical position to the 
default setting. Pressing the RESET button when the V POSITION 
is selected will reset the V POSITION to the default setting.
• When this function is performed on a video signal, s-video signal, 
or component video signal of 525i (480i) or 625i (576i), the range of 
this adjustment depends on the OVER SCAN (
	above) setting. It is 
not possible to adjust when the OVER SCAN is set to 10.
H POSITION8VLQJWKH
x
zEXWWRQVDGMXVWVWKHKRUL]RQWDOSRVLWLRQ
Left
Ù Right
•
Over-adjusting the horizontal position may cause noise to appear 
on the screen. If this occurs please reset the horizontal position to the 
default setting. Pressing the RESET button when the H POSITION is 
selected will reset the H POSITION to the default setting.
• When this function is performed on a video signal, s-video signal, 
or component video signal of 525i (480i) or 625i (576i), the range of 
this adjustment depends on the OVER SCAN (
	above) setting. It is 
not possible to adjust when the OVER SCAN is set to 10.
From the IMAGE menu, items shown in the table below 
can be performed.
6HOHFWDQLWHPXVLQJWKH
x
zFXUVRUEXWWRQVRQWKH

on the projector or remote control, or ENTER button on 
the remote control to execute the item. Then perform it 
according to the following table./07=4)$?
+/#)
 2+%674


5.%6

#761#&,756:%76

#52%6

1845%#0

*2*#5

*5+
						

							30
IMAGE Menu
Item Description
H PHASE
8VLQJWKH
x
Right
Ù Left
• This item can be selected only for an RGB signal or a component 
video signal. (except 525i (480i), 625i (576i), SCART RGB)
H SIZE8VLQJWKH
x
zEXWWRQVDGMXVWVWKHKRUL]RQWDOVL]H
Large
Ù Small
• This item can be selected only for an RGB signal.
• When this adjustment is excessive, the picture may not be 
displayed correctly. In such a case, please reset the adjustment 
by pressing the RESET button on the remote control during this 
operation.
AUTO ADJUST 
EXECUTESelecting this item performs the automatic adjustment feature.
For an RGB signal
The vertical position, the horizontal position, the horizontal phase 
and the horizontal size will be automatically set to default. And the 
aspect ratio will be automatically selected.
Make sure that the application window is set to its maximum size 
prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
For an M1-D signal
The aspect ratio will be automatically set to default.
For a Video signal or S-video signal
The video format best suited for the respective input signal will be 
selected automatically.
This function is available only when the AUTO mode is selected to 
the VIDEO FORMAT item in INPUT menu. For a component video 
\RI
this function.
For a Video signal, S-video signal or Component video signal
The vertical position, horizontal position and aspect ratio will be 
automatically set to default.
For a Component video signal
The horizontal phase will be automatically set to default.
• The automatic adjustment operation requires about 10 seconds. 
Also please note that it may not function correctly with some input.
IMAGE Menu (continued)