Hitachi Projector CP-WX5500 User Manual

							61
IMAGE menu
ItemDescription
OVER SCAN Using the ◄/► buttons adjusts the over-scan ratio.
Small (It magnifies picture)  ó Large (It reduces picture)
• This item can be selected for a video signal.
• 
For HDMITM, MHL and HDBaseTTM signals, this item can also be 
selected if either (1) or (2) applies.
(1)   DIGITAL FORMAT item in the INPUT menu for selected port is 
set to VIDEO.
(2)   DIGITAL
 FORMAT item in the INPUT menu for selected port is 
set to AUTO, and the projector recognizes that it receives video 
signals.
V POSITION Using the ◄/► buttons adjusts the vertical position.
Down  ó Up
• Over-adjusting the vertical position may cause noise to appear on 
the screen. If this occurs, please reset the vertical position to the 
default setting. Pressing the  RESET button when the V POSITION 
is selected will reset the V POSITION to the default setting.
• When this function is performed on a video signal, the range of 
this adjustment depends on OVER SCAN (
 above
) setting. It is not 
possible to adjust when OVER SCAN is set to 10.
• This function is unavailable for a signal from the  LAN, HDMI 1 / 
MHL, HDMI 2 or  HDBaseT port.
H POSITION Using the ◄/► buttons adjusts the horizontal position.
Right  ó Left 
• 
Over-adjusting the horizontal position may cause noise to appear on 
the screen. If this occurs, please reset the horizontal position to the 
default setting. Pressing the  RESET button when the H POSITION is 
selected will reset the H POSITION to the default setting.
• When this function is performed on a video signal, the range of 
this adjustment depends on OVER SCAN (
 above
) setting. It is not 
possible to adjust when OVER SCAN is set to 10.
• This function is unavailable for a signal from the  LAN, HDMI 1 / 
MHL, HDMI 2 or  HDBaseT port.
(continued on next page) 
						

							62
IMAGE menu
ItemDescription
H PHASE
Using the ◄/► buttons adjusts the horizontal phase to eliminate flicker.
Right  ó Left
• This item can be selected only for a computer signal or a 
component video signal. 
• This function is unavailable for a signal from the  LAN, HDMI 1 / 
MHL, HDMI 2 or  HDBaseT port.
H SIZE Using the ◄/► buttons adjusts the horizontal size.
Small  ó Large
• This item can be selected only for a computer signal. 
• This function is unavailable for a signal from the  LAN, VIDEO, 
HDMI 1 / MHL, HDMI 2 or  HDBaseT port.
• When this adjustment is excessive, the picture may not be 
displayed correctly. In such a case, please reset the adjustment 
by pressing the  RESET button on the remote control during this 
operation.
• Images might appear degraded when this function is operated, but 
it is not a malfunction.
AUTO ADJUST  EXECUTE Selecting this item performs the automatic adjustment feature.
For a computer signal
The vertical position, the horizontal position and the horizontal 
phase will be automatically adjusted. 
 
Make sure that the application window is set to its maximum size 
prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
For a video signal
The video format best suited for the respective input signal will 
be selected automatically. This function is available only when 
the AUTO is selected for the VIDEO FORMAT item in the INPUT 
menu (
 64
). The vertical position and horizontal position will be 
automatically set to the default.
• The automatic adjustment operation requires approx. 10 seconds. 
Also please note that it may not function correctly with some input. 
• When this function is performed for a video signal, a certain extra 
such as a line may appear outside a picture.
• When this function is performed for a computer signal, a black 
frame may be displayed on the edge of the screen, depending on 
the computer model. 
• The items adjusted by this function may vary when the FINE or 
DISABLE is selected for the AUTO ADJUST item of the SERVICE 
item in the OPTION menu (
 88
). 
						

							63
INPUT menu
INPUT menu
From the INPUT menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
ItemDescription
PROGRESSIVE Using the ▲/▼ buttons switches the progress mode.
TV  ó FILM 
ó OFF
  
• This function works only for a video signal, component video signal  
(of 480i@60 or 576i@50 or 1080i@50/60), an HDMITM signal  
(of 480i@60 or 576i@50 or 1080i@50/60), an MHL signal (of 480i@60 
or 576i@50 or 1080i@50/60) and HDBaseT
TM signal (of 480i@60 or 
576i@50 or 1080i@50/60).
• When TV or FILM is selected, the screen image will be sharp. 
FILM adapts to the 2-3 Pull-Down conversion system. But these 
may cause a certain defect (for example, jagged line) of the picture 
for a quick moving object. In such a case, please select OFF, even 
though the screen image may lose sharpness.
VIDEO NR Using the ▲/▼ buttons switches the noise reduction mode.
HIGH  ó MID 
ó LOW
   
• This function works only for a video signal, component video signal  
(of 480i@60 or 576i@50 or 1080i@50/60), an HDMITM signal  
(of 480i@60 or 576i@50 or 1080i@50/60), an MHL signal (of 480i@60 
or 576i@50 or 1080i@50/60) and HDBaseT
TM signal (of 480i@60 or 
576i@50 or 1080i@50/60). 
COLOR SPACE Using the ▲/▼ buttons switches the mode for color space.
AUTO  ó RGB 
ó SMPTE240 
ó REC709 
ó REC601
      • This item can be selected only for a computer signal (except for 
signals from the  LAN port).
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well at some signals. In such a 
case, it might be good to select a suitable mode except AUTO.
(continued on next page) 
						

							64
INPUT menu
ItemDescription
VIDEO FORMAT The video format for 
VIDEO port can be set.
Using the ◄/► buttons  
switches the mode for video 
format.
AUTO   ó  NTSC  
ó  PAL  
ó  SECAM
       N-PAL  ó M-PAL 
ó NTSC4.43 
• This item is performed only for a video signal from the  VIDEO port.
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well for some signals. If the 
picture becomes unstable (e.g. an irregular picture, lack of color), 
please select the mode according to the input signal.
DIGITAL FORMAT
The digital format of HDMITM/MHL input signals from the  HDMI 1/
MHL, HDMI2  and HDBaseTTM ports can be set.
(1)   Use the ▲/▼ buttons to select the port to be set.
(2)   Use the ◄/►buttons to select the digital format.
AUTO  ó VIDEO 
ó COMPUTER
AUTO: automatically sets the optimum mode.
VIDEO: sets the suitable mode for DVD signals.
COMPUTER: sets the suitable mode for computer signals.
• When the COMPUTER is selected, the function OVER SCAN 
(IMAGE menu) is unavailable.
(continued on next page)
CP-WU5505/CP-WX5505 CP-X5555 CP-WU5500/CP-WX5500
CP-X5550 
						

							65
INPUT menu
CP-WU5505/CP-WX5505CP-X5555
Item Description
DIGITAL RANGE
The digital range of HDMITM/MHL input signals from the  HDMI 1/
MHL, HDMI 2  and HDBaseTTM ports can be set.
(1)   Use the ▲/▼ buttons to select the port to be set.
(2)   Use the ◄/►buttons to select the digital range.
AUTO  ó NORMAL 
ó ENHANCED
AUTO:   automatically sets the optimum mode.
NORMAL:   sets the suitable mode for DVD signals. (16-235)
ENHANCED :  
sets the suitable mode for computer signals. (0-255)
• If the contrast of the screen image is too strong or too weak, try 
finding a more suitable mode.
COMPUTER IN The computer input signal type for 
COMPUTER IN port can be set.
Use the ◄/► buttons to select the 
computer input signal type. AUTO  ó SYNC ON G OFF
• Selecting the AUTO mode allows   
you to input a sync on G signal or component video signal from the 
port.
• In the AUTO mode, the picture may be distorted with certain 
input signals. In such a case, remove the signal connector so that 
no signal is received and select the SYNC ON G OFF, and then 
reconnect the signal.
FRAME LOCK Set the frame lock function on/off for each port.
(1)  
Use the ▲/▼ buttons to select the input ports.
(2)   Use the ◄/► buttons to turn the frame lock function on/off .
ON  ó OFF
• This item can be performed only on a signal with a vertical 
frequency of 49 to 51Hz, 59 to 61 Hz.
• When ON is selected, moving pictures are displayed more 
smoothly.
(continued on next page)
CP-WU5500/CP-WX5500 CP-X5550
CP-WU5505/CP-WX5505 CP-X5555 CP-WU5500/CP-WX5500
CP-X5550 
						

							66
INPUT menu
ItemDescription
RESOLUTION The resolution for the 
COMPUTER IN input signal can be set on this 
projector.
(1)   In the INPUT menu select the RESOLUTION using the ▲/▼ 
buttons and press the ► button. 
The RESOLUTION menu will be   
displayed.
(2)   In the RESOLUTION menu select the 
resolution you wish to display using 
the ▲/▼ buttons.   
Selecting AUTO will set a resolution 
appropriate to the input signal.
(3)   Pressing the ► or  ENTER button when 
selecting a STANDARD resolution will 
automatically adjust the horizontal and 
vertical positions, clock phase and 
horizontal size. The INPUT_INFORMATION dialog will be 
displayed.
(4)    To set a custom resolution use the ▲/▼ buttons to select 
the CUSTOM and the RESOLUTION_CUSTOM box will be 
displayed.  Set the (HORZ) and (VERT) 
resolutions using the ▲/▼/◄/► 
buttons. 
This function may not support all 
resolutions.
(5)   Move the cursor to OK on screen and press the ► or  ENTER 
button. The message "ARE YOU SURE YOU WISH TO CHANGE 
RESOLUTION?" appears. To save the setting, press the ► 
button.  
The horizontal and vertical positions, clock phase and horizontal 
size will be automatically adjusted. The INPUT_INFORMATION dialog 
will be displayed.
(6)    To revert back to the previous resolution without saving changes, 
move the cursor to CANCEL on screen and press the ◄ or 
ENTER  button. 
The screen will then return to the RESOLUTION menu displaying 
the previous resolution.
• For some pictures, this function may not work well.
(continued on next page)
STANDARD   ↓
CUSTOM  ↓ 
						

							67
INPUT menu
ItemDescription
PbyP / PinP  
SETUP PinP POSITION
Using ▲/▼ buttons on the remote control changes the position of 
sub area in PinP mode (
50).
PbyP / PinP FRAME LOCK
Select the screen that enables FRAME LOCK function when using 
PbyP or PinP.
LEFT / PRIMARY: Enables FRAME LOCK function for input on left 
screen of PbyP or on primary area of PinP.
RIGHT / SECONDARY: Enables FRAME LOCK function for input on 
right screen of PbyP or on secondary area of PinP.
MHL STANDBY PWR. Using the ▲/▼ buttons switches the MHL STANDBY PWR. ON/
OFF.
ON ó OFF
• When the STANDBY MODE is set to SAVING, the MHL STANDBY 
PWR. menu cannot be operated and MHL power feeding is 
unavailable with standby mode  (
72).
• When the MHL STANDBY PWR. is set to ON, there may be some 
noise with standby mode. This is not malfunction. 
						

							68
SETUP menu
SETUP menu
From the SETUP menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
ItemDescription
GEOMETRY  
CORRECTION KEYSTONE
Selecting this item displays the KEYSTONE dialog.
For details, see KEYSTONE in  Correcting the distortion(
38).
• When the zoom adjustment is set to the TELE (telephoto focus), 
this function may be excessive. This function should be used when 
the zoom adjustment is set to the full WIDE (wide-angle focus) 
whenever possible.
• When the horizontal lens shift is not set to the center, this function 
may not work well.
• 
This function is unavailable when the screen is activated by 
PERFECT FIT (
39), and WARPING (40) .
PERFECT FIT
Selecting this item displays the PERFECT FIT dialog. For details, 
see PERFECT FIT in  Correcting the distortion  (
39).
• 
This function is unavailable when the screen is activated by 
KEYSTONE (
38), and WARPING (40) .
WARPING
Selecting this item displays the WARPING dialog. For details, see 
Application Manual of this feature .
•  This function is unavailable when the screen is activated by 
KEYSTONE 
(38) and PERFECT FIT (39).
EDGE BLENDING
Selecting this item displays the EDGE BLENDING dialog. For 
details, see EDGE BLENDING feature (
41 ~ 44).
(continued on next page) 
						

							69
SETUP menu
ItemDescription
GEOMETRY  
CORRECTION (continued) PATTERN
Select PATTERN with ▲/▼ 
buttons.
Displayed pattern [Off/1/2/3/4/5/6] can be switched with  ◄/► buttons.PATTERN 1: Frame
PATTERN 2: Red Grid
PATTERN 3: Green Grid
PATTERN 4: Blue Grid
PATTERN 5: Vertical 9 steps
PATTERN 6: Horizontal 9 steps
OFF:  Displays the input  signal.
LAMP & FILTER Selecting this item displays the LAMP 
& FILTER menu.
Select an item using the ▲/▼ buttons, 
and press the ► button or the 
ENTER 
button on the remote control to 
execute the item.
ECO MODE
Using the ▲/▼ buttons switches the Eco mode.
   NORMAL  ó ECO 
•    When the item other than NORMAL is selected, acoustic noise and 
screen brightness are reduced.
LAMP TIME 
The lamp time is the usage time of the lamp, counted after the last 
resetting. It is shown in the LAMP & FILTER menu.
Pressing the  RESET button on the remote control or the ► button 
of the projector displays a dialog.
To reset the lamp time, select the OK using the ► button.
CANCEL  ð OK
• For the lamp replacement, see the section  Replacing the lamp 
(
103).
•  The IMAGE OPTIMIZER function does not work properly unless 
LAMP TIME is initialized when replacing a lamp.
(continued on next page) 
						

							70
SETUP menu
ItemDescription
LAMP & FILTER (continued) FILTER TIME
The filter time is the usage time of the air filter, counted after the last 
resetting. It is shown in the 
LAMP & FILTER menu.
Pressing the  RESET button on the remote control or the ► button 
of the projector displays a dialog. 
To reset the filter time, select the OK using the ► button.
CANCEL  ð OK
• Please reset the filter time only when you have cleaned or 
replaced the air filter, for a suitable indication about the air filter.
• For the air filter cleaning, see the section Cleaning and replacing
the air filter (
105).
FILTER MESSAGE
Use the ▲/▼ button to set the timer for notifying by the message 
when to replace the filter unit 
1000h  ó 2000h 
ó 5000h 
ó 10000h 
ó 15000h 
ó 20000h 
ó 25000h 
ó 30000h 
ó OFF
After choosing an item except OFF, the message “REMINDER *** 
HRS PASSED ....” will appear after the timer reaches the interval 
time set by this feature. 
When the OFF is chosen, the message will not appear. Utilize this 
feature to keep the air filter clean, setting the suitable time according 
to your environment of this projector.
• Please take care of the filter unit periodically, even if there is 
no message. If the air filter becomes to be blocked by dust or 
other matter, the internal temperature will rise, which could cause 
malfunction, or reduce the lifetime of the projector.
• Please be careful with the operating environment of the projector 
and the condition of the filter unit.
IMAGE
OPTIMIZER
When this function is enabled, automatic image correction is 
performed to maintain visibility in accordance with lamp deterioration.
• This function may not work properly when HDCR/ACCENTUALIZER 
is set to other than 0.
• This function does not work properly unless LAMP TIME is initialized 
when replacing a lamp. 
(continued on next page)