Hitachi Projector CP-WU9100 User Manual

							91
OPTION menu
ItemDescription
SERVICE(continued)COMMUNICATION
Selecting this item displays COMMUNICATION menu. In this menu, you can configure the serial communication settings of the projector using the CONTROL port.
• Select an item using the cursor buttons ▲/▼. Then pressing the ► button opens the submenu for the setting item you selected. Or, pressing the ◄ button instead of the ► button makes the menu back to the previous one without changing the setup. Each submenu can be operated as described above.• When COMMUNICATION TYPE (below) is set to OFF, the other items except STACK in COMMUNICATION menu are invalid.• For the function of serial communication, refer to the Network Guide.
COMMUNICATION TYPE
Select the communication type for transmission using the CONTROL port.
NETWORK BRIDGE (WIRELESS)   NETWORK BRIDGE (WIRED)    OFF
NETWORK BRIDGE: Select this type, if it is required to control an external device as a network terminal, using this projector from the computer. Select WIRELESS or WIRED as your network connection mode.The CONTROL port doesn't accept RS-232C  commands ( Network Bridge Function in the Network Guide)
OFF: Select this mode to receive RS-232C commands using the CONTROL port. 
• OFF is the default setting. • When you select the NETWORK BRIDGE, check the item, TRANSMISSION METHOD (92).
(continued on next page) 
						

							92
OPTION menu
ItemDescription
SERVICE(continued)COMMUNICATION(continued)
SERIAL SETTINGS
Select the serial communication condition for the CONTROL port.
BAUD RATE
4800bps  9600bps  19200bps  38400bps      
 PARITY
NONE  ODD  EVEN    
• The BAUD RATE is fixed to 19200bps and PARITY is fixed NONE when the COMMUNICATION TYPE 
is set to OFF (91).
TRANSMISSION METHOD
Select the transmission method for communication by the NETWORK BRIDGE from the CONTROL port.
HALF-DUPLEX  FULL-DUPLEX
HALF-DUPLEX: This method lets the projector make two way communication, but only one direction, either transmitting or receiving data, is allowed at a time.
FULL-DUPLEX: This method lets the projector make two way communication, transmitting and receiving data at the same time.
• HALF-DUPLEX is selected as the default setting.• If you select HALF-DUPLEX, check the setting of 
the item RESPONSE LIMIT TIME (93).
(continued on next page) 
						

							93
OPTION menu
ItemDescription
SERVICE(continued)COMMUNICATION(continued)
RESPONSE LIMIT TIME
Select the time period to wait for receiving response data from other device communicating by the NETWORK BRIDGE and the HALF-DUPLEX through the CONTROL port.
OFF  1s  2s  3s    
OFF: Select this mode if it is not required to check the responses from the device that the projector sends data to. In this mode, the projector can send out data from the computer continuously.
1s /2s /3s: Select the time period to keep the projector waiting for response from the device that the projector sends data to. While waiting a response, the projector does not send out any data from the CONTROL port.
• This menu is available only when the NETWORK BRIDGE is selected for the COMMUNICATION TYPE and the HALF-DUPLEX is selected for the TRANSMISSION METHOD (92).• OFF is selected as the default setting.
STACK
Selecting this item displays the STACK menu. For more information, see the Instant Stack Guide. • When STACK MODE is set to MAIN or SUB, 
the other items in COMMUNICATION menu are invalid.
(continued on next page) 
						

							94
OPTION menu
ItemDescription
SERVICE(continued)
INFORMATION
Selecting this item displays a dialog titled “INPUT INFORMATION”. It shows the information about the current input.
• The “FRAME LOCK” message on the dialog means the frame lock function is working. • This item cannot be selected for no signal and sync out.• When the MY TEXT DISPLAY is set to ON, the MY TEXT is displayed together with the input information in the  
INPUT INFORMATION box (100).
FACTORY RESET
Selecting OK using the ► button performs this function. By this function, all menu items are collectively returned to the initial setting. Note that the settings of the following items cannot be reset: LAMP-1 TIME, LAMP-2 TIME, FILTER TIME, LANGUAGE, AUTO BLANK, FILTER MESSAGE, STANDBY MODE, COMMUNICATION, NETWORK, SECURITY 
CANCEL  OK 
						

							95
NETWORK menu
See the Network Guide for details of NETWORK operation.
Remember that incorrect network settings on this projector may cause trouble 
on the network. Consult with your network administrator before connecting to an 
existing access point on your network.
NETWORK menu 
						

							96
Security
ItemDescription
SECURITY PASSWORD CHANGE
(1)  Use the ▲/▼ buttons on the SECURITY menu to select SECURITY PASSWORD CHANGE and press the ► button to display the ENTER NEW PASSWORD box.(2)  Use the ▲/▼/◄/► buttons to enter the new password.(3)  Move the cursor to the right side of the ENTER NEW PASSWORD box and press the ► button to display the NEW PASSWORD AGAIN box, enter the same password again. (4)  Move the cursor to the right side of the NEW PASSWORD AGAIN box and press the ► button and the NOTE NEW PASSWORD box will be displayed for about 30 seconds. Make note of the password during this time.Pressing the ENTER button on the remote control or ► button on the projector will close the NOTE NEW PASSWORD box.
• Do not forget your password.
SECURITY menu
This projector is equipped with security functions.From the SECURITY menu, items shown in the table below can be performed.To use SECURITY menu: User registration is required before using the security functions.
Enter to the SECURITY menu
1.  Press the ► button. The ENTER PASSWORD box will be displayed.  
2.  Use the ▲/▼/◄/► buttons to enter the registered password. The factory default password is as follows. 
      CP-WU9100 :1728
      CP-HD9950 : 6125
   This password can be changed (below). Move the cursor to the right side of the ENTER PASSWORD box and press the ► button to display the SECURITY menu.
• It is strongly recommended the factory default password to be changed as soon as possible.• If an incorrect password is input, the ENTER PASSWORD box will be displayed again. If incorrect password is input three times, the projector will turn off. Afterwards the projector then will turn off every time an incorrect password is input.3.  Items shown in the table below can be performed.
If you have forgotten your password(1)   While the ENTER PASSWORD box is displayed, press and hold the RESET button on the remote control for approximately three seconds or press and hold the INPUT button for three seconds while pressing the ► button on the projector.
(2)  
The 10 digit Inquiring Code will be displayed. Contact your dealer with the 10 digit Inquiring Code. Your password will be sent after your user registration information is confirmed.
• If there is no key input for approximately 55 seconds while the Inquiring Code is displayed, the menu will close. If necessary, repeat the process from (1).  
(continued on next page) 
						

							97
Security
ItemDescription
MyScreen PASSWORD
The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten.
1 Turning on the MyScreen PASSWORD1-1  Use the ▲/▼ buttons on the SECURITY menu to select MyScreen PASSWORD and press the ► button to display the MyScreen PASSWORD on/off menu.1-2  Use the ▲/▼ buttons on the MyScreen PASSWORD on/off menu to select ON. The ENTER NEW PASSWORD box (small) will be displayed.1-3  Use the ▲/▼/◄/► buttons to enter the password. Move the cursor to the right side of the ENTER NEW PASSWORD box (small) and press the ► button to display the NEW PASSWORD AGAIN box, enter the same PASSWORD again.1-4  Move the cursor to the right side of the NEW PASSWORD AGAIN box and press the ► button to display the NOTE NEW PASSWORD box for about 30 seconds. Make note of the password during this time. Pressing the ENTER button on the remote control or ► button on the projector will return to MyScreen PASSWORD on/off menu.
When a password is set for MyScreen:
• The MyScreen registration function (and menu) will be unavailable.
• The MyScreen Lock menu will be unavailable.
• The START UP setting will be locked on MyScreen (and the menu will be unavailable).Turning the MyScreen PASSWORD off will allow normal operation of these functions.
• Do not forget your MyScreen PASSWORD.
2 Turning off the MyScreen PASSWORD2-1  Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off menu.2-2  
Select OFF to display the ENTER PASSWORD box (large). Enter the registered password and the screen will return to the 
     MyScreen PASSWORD on/off menu.
If an incorrect PASSWORD is entered, the menu will close. If necessary, repeat the process from 2-1.
3 If you have forgotten your password3-1  Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off menu.3-2  Select OFF to display the ENTER PASSWORD box (large). The 10 digit Inquiring Code will be displayed inside the box.
3-3  Contact your dealer with the 10 digit Inquiring Code. Your password will be sent after your user registration information is confirmed.
ENTER NEW PASSWORD box (small)
ENTER PASSWORD box (large)
(continued on next page) 
						

							98
Security
ItemDescription
PIN LOCK
PIN LOCK is a function which prevents the projector from being used unless a registered Code is input.
1 Turning on the PIN LOCK1-1  Use the ▲/▼ buttons on the SECURITY menu to select PIN LOCK and press the ► button or the ENTER button to display the PIN LOCK on/off menu.1-2  Use the ▲/▼ buttons on the PIN LOCK on/off menu to select ON and the Enter PIN Code box will be displayed. 1-3  Input a 4 part PIN code using the ▲/▼/◄/►, COMPUTER 1 or INPUT button. The PIN Code again box will appear. Reenter  the same PIN code. This will complete the PIN code registration.
• If there is no key input for about 55 seconds  while the Enter PIN Code box or the PIN Code again box is displayed, the menu will close. If necessary, repeat the process from 1-1.
Anytime the projector is restarted after AC power  is turned off the Enter PIN Code box will be displayed. Enter the registered PIN code.The projector can be used after entering the registered PIN code. If an incorrect PIN code is input, the Enter PIN code box will be displayed again.If an incorrect PIN code is input three times, the projector will turn of f. Afterwards the projector will turn off every time an incorrect PIN code is input. The projector will also turn off if there is no key input for approximately five minutes while the Enter PIN code box is displayed.This function will activate only when the projector is started after AC power is turned off.
• Do not forget your PIN code.
2 Turning off the PIN LOCK2-1  Follow the procedure in 1-1 to display the PIN LOCK on/off menu. 2-2  Use the ▲/▼ buttons to select OFF and the Enter PIN Code box will be displayed. Enter the registered PIN code to turn the PIN LOCK function off.
If an incorrect PIN code is input three times, the projector will turn of f. 
3 If you have forgotten your PIN code3-1  While the Enter PIN code box is displayed, press and hold the RESET button for three seconds or press and hold the INPUT button for three seconds while pressing the ► button on the projector. The 10 digit Inquiring Code will be displayed.
• If there is no key input for approximately five minutes while the Inquiring Code is displayed, the projector will turn off.3-2  Contact your dealer with the 10 digit Inquiring Code. Your PIN code will be sent after your user registration information is confirmed.
(continued on next page) 
						

							99
Security
ItemDescription
MY TEXT PASSWORD
The MY TEXT PASSWORD function can prevent the MY TEXT from being overwritten. When the password is set for the MY TEXT;• The MY TEXT DISPLAY menu will be unavailable, which can prohibit changing the DISPLAY setting.• The MY TEXT WRITING menu will be unavailable, which can prevent the MY TEXT from being overwritten.
1 Turning on the MY TEXT PASSWORD1-1  Use the ▲/▼ buttons on the SECURITY menu to select the MY TEXT PASSWORD and press the ► button to display the MY TEXT PASSWORD on/off menu.1-2  Use the ▲/▼ buttons on the MY TEXT PASSWORD on/off menu to select ON. The ENTER NEW PASSWORD box (small) will be displayed.1-3  Use the ▲/▼/◄/► buttons to enter the password. Move the cursor to the right side of the ENTER NEW PASSWORD box (small) and press the ► button to display the NEW PASSWORD AGAIN box, and then enter the same password again.1-4  Move the cursor to the right side of the NEW PASSWORD AGAIN box and press ► button to display the NOTE NEW PASSWORD box for about 30 seconds. Make note of the password.
Pressing the ENTER button on the remote control or ► button on the projector will return to the MY TEXT PASSWORD on/off menu. 
2 Turning off the MY TEXT PASSWORD2-1  Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off menu.2-2  Select OFF to display the ENTER PASSWORD box (large). Enter the registered password and the screen will return to the MY TEXT PASSWORD on/off menu. 
If an incorrect password is input, the menu will close. If necessary, repeat the process from 2-1
3 If you have forgotten your password3-1  Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off menu.3-2  Select OFF to display the ENTER PASSWORD box (large). The 10 digit inquiring code will be displayed inside the box. 3-3  Contact your dealer with the 10 digit inquiring code. Your password will be sent after your user registration information is confirmed.
ENTER NEW PASSWORD  box (small)
ENTER PASSWORD box (large)
(continued on next page) 
						

							100
Security
ItemDescription
MY TEXT DISPLAY
(1)  Use the ▲/▼ buttons on the SECURITY menu to select the MY TEXT DISPLAY and press the ► or ENTER button to display the MY TEXT DISPLAY on/off menu.
(2)  Use the ▲/▼ buttons on the MY TEXT DISPLAY on/off menu to select on or off.
ON  OFF
When it is set ON, the MY TEXT will be displayed on the START UP screen and the INPUT INFORMATION when the INFORMATION on the SERVICE menu is chosen.
• This function is available only when the MY TEXT PASSWORD function is set to the OFF.
MY TEXT WRITING
(1)  Use the ▲/▼ buttons on the SECURITY menu to select the MY TEXT WRITING and press the ► button. The MY TEXT WRITING dialog will be displayed.
(2)  
The current MY TEXT will be displayed on the first three lines. If not yet written, the lines will be blank.  Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to select and enter characters. To erase one  character at one time, press the RESET button or press the ◄ and INPUT button at the same time. If you move the cursor to DELETE or CLEAR ALL on screen and press the ENTER or INPUT button, one or all characters will be erased. The MY TEXT can be input up to 24 characters on each line.
(3)  
To change an already inserted character, press the ▲/▼ button to move the cursor to one of the first three lines, and use the ◄/► buttons to move the cursor on the character to be changed.After pressing the ENTER or INPUT button, the character is selected. Then, follow the same procedure as described at the item (2) above.
(4)  
To finish entering text, move the cursor to the OK on screen and press the ►, ENTER or INPUT button. To revert to the previous MY TEXT without saving changes, move the cursor to the CANCEL on screen and press the ◄, ENTER or INPUT button.
• The MY TEXT WRITING function is available only when the MY TEXT PASSWORD function is set to OFF.
(continued on next page)