Hitachi Projector CP-WU5505 User Manual

							31
1.Press the STANDBY/ON button on the projector or the remote control.  
The message “Power off?” will appear on the screen for about 5 seconds.
Turning off  the power
2.Press the STANDBY/ON button again while the message appears.   
The projector lamp will go off, and the POWER indicator will begin blinking 
in orange. Then the POWER indicator will stop blinking and light in steady 
orange when the lamp cooling is complete (
11 2 ).
3.Attach the lens cover, after the  POWER indicator turns to steady orange.
Do not turn the projector on for about 10 minutes or more after turning it of f. 
Also, do not turn the projector off shortly after turning it on. Such operations might 
cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.
Power on/off
►A strong light is emitted when the projector’s power is on.  
Do not look into the lens of the projector or look inside of the projector through 
any of the projector’s openings since the projection ray may cause a trouble on 
your eyes.
►Keep any object away from concentrated projection light beam. Blocking the 
beam by something causes high temperature and could result in fire or smoke.
►Do not touch around the lamp cover and the exhaust vents during use or just 
after use, since it is too hot. WARNING
• Turn the power on/off in right order. Please power on the projector 
prior to the connected devices. 
• 
This projector has the function that can make the projector automatically turn on/
off. Please refer to the DIRECT POWER ON 
( 83) and AUTO POWER OFF (83) 
items of the OPTION menu.
 
NOTE 
						

							32
Operating
Operating
Adjusting the volume
Use the VOLUME +  / - buttons to adjust the volume. 
A dialog will appear on the screen to aid you in   
adjusting the volume. If you do not do anything, the 
dialog will automatically disappear after a few seconds.
• 
When  is selected for current picture input port, the volume 
adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu (
 75).
• Even if the projector is in the standby mode, the volume is adjustable when 
both of the following conditions are true:
-   An option other than 
 is selected for AUDIO OUT in the STANDBY 
OUTPUT item of the SETUP menu (
74).
- NORMAL is selected in the STANDBY 
MODE item of the SETUP menu ( 72).
Press MUTE button on the remote control.
A dialog will appear on the screen indicating  
that you have muted the sound.
To restore the sound, press the MUTE, VOLUME + 
or VOLUME - button. Even if you do not do anything,  
the dialog will automatically disappear after a few seconds.
ASPECT
BLANKESC MENU
RESET
AUTOPAGEDOWN
ONOFFFREEZE
UP
ENTER
FOCUS- +ZOOM- +
INPUT
INTERACTIVE
MYBUTTON1
2PbyPMAGNIFYVOLUME-
+GEOMETRY PICTURE MUTE
NETWORK
OSD MSG
ASPECT
BLANK
ESC MENU
RESET
AUTO
PAGE
DOWN
ON
OFF
FREEZE
UP
ENTER
FOCUS
- +
ZOOM
- +
INPUT
INTERACTIVE
MYBUTTON1
2
PbyP
MAGNIFYVOLUME
-
+
GEOMETRY PICTURE MUTE
NETWORK
OSD MSG
VOLUME + / -  
buttons
NOTE
Temporarily muting the sound
ASPECT
BLANKESC MENU
RESET
AUTOPAGEDOWN
ONOFFFREEZE
UP
ENTER
FOCUS- +ZOOM- +
INPUT
INTERACTIVE
MYBUTTON1
2PbyPMAGNIFYVOLUME-
+GEOMETRY PICTURE MUTE
NETWORK
OSD MSGMUTE  
button
ASPECT
BLANK
ESC MENU
RESET
AUTO
PAGE
DOWN
ON
OFF
FREEZE
UP
ENTER
FOCUS
- +
ZOOM
- +
INPUT
INTERACTIVE
MYBUTTON1
2
PbyP
MAGNIFYVOLUME
-
+
GEOMETRY PICTUREMUTE
NETWORK
OSD MSG
NOTE• When     is selected for current picture input port, the sound is always 
muted.
Please see AUDIO SOURCE item of AUDIO menu (
75).
• C.C. (Closed Caption) is automatically activated when sound is muted and an 
input signal containing C.C. is received. This function is available only when the 
signal is NTSC for VIDEO or COMPUTER IN, and when AUTO is selected for 
DISPLAY in the C.C. menu under the SCREEN menu (
81). 
						

							33
Operating
Press INPUT button on the projector or the remote 
control. Select a desirable input referring to the 
displayed input list.
Selecting an input signal
           LAN   COMPUTER IN     HDMI 1 / MHL
         VIDEO                                      
         HDBaseT*                             HDMI 2
• If you have set SKIP to some ports from SOURCE SKIP in the 
OPTION menu, the input from the ports cannot be selected (
 82).
• While ON is selected for AUTO SEARCH item in OPTION menu, the projector 
will keep checking the ports in above order repeatedly till an input signal is 
detected (
 82).
NOTE
* CP-WU5505/CP-WX5505/CP-X5555 onlyASPECT
BLANKESC
MENU
RESET
AUTOPAGEDOWN
ONOFFFREEZE
UP
ENTER
FOCUS- +ZOOM- +
INPUT
INTERACTIVE
MYBUTTON1
2PbyPMAGNIFYVOLUME-
+GEOMETRY PICTURE MUTE
NETWORK
OSD MSG
INPUT  button
ASPECT
BLANK
ESC MENU
RESET
AUTO
PAGE
DOWN
ON
OFF
FREEZE
UP
ENTER
FOCUS
- +
ZOOM
- +
INPUT
INTERACTIVE
MYBUTTON1
2
PbyP
MAGNIFYVOLUME
- +
GEOMETRY PICTURE MUTE
NETWORK
OSD MSG
INPUT  button 
						

							34
Operating
ASPECT
BLANKESCMENU
RESET
AUTOPAGEDOWN
ONOFFFREEZE
UP
ENTER
FOCUS- +ZOOM- +
INPUT
INTERACTIVE
MYBUTTON1
2PbyPMAGNIFYVOLUME-
+GEOMETRY PICTURE MUTE
NETWORK
OSD MSG
Selecting an aspect ratio
Press ASPECT button on the remote control.   
Each time you press the button, the projector 
switches the mode for aspect ratio in turn. 
• ASPECT button does not work when no proper signal is input.
• NORMAL mode keeps the original aspect ratio setting. NOTE
  
For a computer signal  
CP-X5550, CP-X5555:   
  NORMAL  4:3  16:9  16:10  ZOOM  
         
 
CP-WU5500, CP-WX5500, CP-WU5505, CP-WX5505:  
  NORMAL  4:3  16:9  16:10  ZOOM   NATIVE 
        
  For a video signal  
CP-X5550, CP-X5555:  
  4:3  16:9  14:9  ZOOM 
  
 
CP-WU5500, CP-WX5500, CP-WU5505, CP-WX5505 : 
  4:3  16:9  16:10  14:9  ZOOM   NATIVE 
  
   For an input signal from the LAN port, or if the re is no signal  
CP-X5550, CP-X5555:  4:3 (fixed) 
CP-WU5500, CP-WX5500, CP-WU5505, CP-WX5505:  16:10 (fixed)
  
For HDMI
TM , HDBaseTTM and MHL signals 
CP-X5550, CP-X5555:  
  NORMAL  4:3  16:9  16:10  14:9  ZOOM  
         
 
CP-WU5500, CP-WX5500, CP-WU5505, CP-WX5505:  
  NORMAL   4:3  16:9  16:10  14:9  ZOOM   NATIVE 
        
ASPECT
BLANK
ESC MENU
RESET
AUTO
PAGE
DOWN
ON
OFF
FREEZE
UP
ENTER
FOCUS
- +
ZOOM
- +
INPUT
INTERACTIVE
MYBUTTON1
2
PbyP
MAGNIFYVOLUME
-
+
GEOMETRY PICTURE MUTE
NETWORK
OSD MSG
ASPECT  button 
						

							35
Operating
Adjusting the projector’s elevator
When the place to put the projector is slightly 
uneven to the left or right, use the elevator feet to 
place the projector horizontally. Using the feet can 
also tilt the projector in order to project at a 
suitable angle to the screen, elevating the front 
side of the projector within 11 degrees.
This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is 
adjustable while pushing the elevator button on the same side as it.
1. 
Holding the projector, push the elevator buttons to loose the elevator feet.
2. 
Position the front side of the projector to the desired height.
3. 
Release the elevator buttons in order to lock the elevator feet.
4. 
After making sure that the elevator feet are locked, put the projector down 
gently.
5. 
If necessary, the elevator feet can be manually twisted to make more precise 
adjustments. Hold the projector when twisting the feet.
11°
To loose an elevator foot, 
push the elevator button 
on the same side as it.To fi nely adjust, 
twist the foot.
CAUTION  ►Do not handle the elevator buttons without holding the 
projector, since the projector may drop down.
►Do not tilt the projector other than elevating its front within 1 1 degrees using 
the adjuster feet. A tilt of the projector exceeding the restriction could cause 
malfunction or shortening the lifetime of consumables, or the projector itself.
1.Use the ZOOM  ring to adjust the screen size.
2.Use the FOCUS ring to focus the picture.
Adjusting the zoom and focusFOCUS ring
ZOOM 
ring 
						

							36
Operating
Adjusting the lens shift
1.  
Turn the  VERTICAL  adjuster fully counter 
clockwise. Then turn it clockwise and 
adjust the vertical lens position upward.
2.    Turn the  HORIZONTAL  adjuster clockwise 
or counter clockwise to adjust the 
horizontal lens position.
CAUTION   ►Operate the lens adjusters gently as the lens may malfunction
when subjected to shocks. It may need more strength to turn the adjusters near
the adjustment limits. Be careful not to apply too much strength. If the lens adjuster 
is turned excessively, it runs idle by a clutch mechanism inside the adjuster. 
Although it makes a clicking sound, it is not a malfunction. When the lens adjuster 
runs idle, the lens shift cannot be performed further. Turn the lens adjuster to the 
opposite direction to adjust the lens shift. When the lens adjuster is turned too 
quickly, it may make a clicking sound by a clutch mechanism. In that case, turn it 
slowly to adjust the lens shift.
・ When adjusting the lens shift to the maximal oblique direction, the periphery of 
the projected screen may be dark or a shadow may be cast.
・ When adjusting the lens shift vertically, perform it by moving the projected 
screen upward. If adjusting the lens shift by moving the projected screen 
downward, the projected screen may be adjusted slightly low.
NOTE  • When the lens adjuster runs idle 
with a clicking sound and it still makes a sound 
by a clutch mechanism even if it is turned to the 
opposite direction, turn the lens adjuster while  pressing it downward to perform the lens shift.
V
H
V50%
H5%   :CP-WX5505/CP-X5555/CP-WX5500/CP-X5550
H4.4%:CP-WU5505/CP-WU5500
VERTICAL  adjuster
HORIZONTAL  adjuster 
						

							37
Operating
Press AUTO button on the remote control.  
Pressing this button performs the following.
Using the automatic adjustment feature
  For a computer signal  
The vertical position, the horizontal position and the   
horizontal phase will be automatically adjusted.   
Make sure that the application window is set to its   
maximum size prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
   For a video signal  
The video format best suited for the respective input signal will be selected 
automatically. This function is available only when the AUTO is selected for 
the VIDEO FORMAT item in the INPUT menu (
64). The vertical position and 
horizontal position will be automatically set to the default.
    For a component video signal   
The vertical position and horizontal position will be automatically set to the default. 
The horizontal phase will be automatically adjusted.
• The automatic adjustment operation requires approx. 10 seconds. Also 
please note that it may not function correctly with some input. 
• When this function is performed for a video signal, a certain extra such as a line 
may appear outside a picture.
• When this function is performed for a computer signal, a black frame may be 
displayed on the edge of the screen, depending on the computer model. 
• 
The items adjusted by this function may vary when the FINE or DISABLE is selected 
for the AUTO ADJUST item of the SERVICE item in the OPTION menu (
88).
NOTE
ASPECT
BLANKESC MENU
RESET
AUTOPAGEDOWN
ONOFFFREEZE
UP
ENTER
FOCUS- +ZOOM- +
INPUT
INTERACTIVE
MYBUTTON1
2PbyPMAGNIFYVOLUME-
+GEOMETRY PICTURE MUTE
NETWORK
OSD MSG
ASPECT
BLANK
ESC MENU
RESET
AUTO
PAGE
DOWN
ON
OFF
FREEZE
UP
ENTER
FOCUS
- +
ZOOM
- +
INPUT
INTERACTIVE
MYBUTTON1 2
PbyP
MAGNIFYVOLUME
-
+
GEOMETRY PICTURE MUTE
NETWORK
OSD MSG
AUTO  button 
						

							38
Operating
KEYSTONE:   allows you to adjust the vertical and 
horizontal keystone.
PERFECT FIT :   
allows you to adjust each of the screen 
corners and sides to correct the 
distortion.
WARPING:   allows you to project an image on several 
types of screen.
• The menu or dialog will automatically disappear after several seconds 
of inactivity. Press the GEOMETRY button again, or point the cursor at EXIT in 
the dialog and press the ►or  ENTER button to end the operation and close the 
menu or dialog.  NOTE
To correct the distortion of projected screen, you can select one of three options, 
KEYSTONE, PERFECT FIT, and WARPING. First press the GEOMETRY button 
to display the GEOMETRY CORRECTION menu, and point at one of the items 
with the ▲/▼ buttons.
Correcting the distortion 
Then follow the procedure shown below for the item you selected.  Use  KEYSTONE  / PERFECT FIT / WARPING for adjustment. When one of 
them is selected, other items are not available.
    
KEYSTONE: 
When KEYSTONE is pointed at, pressing the ► or 
ENTER  button displays the KEYSTONE dialog.
1. 
Select the vertical or horizontal keystone ( / ) 
with the ▲/▼ buttons.
2. 
Use the ◄/► buttons to adjust the keystone distortion.
• When the zoom adjustment is set to the TELE (telephoto focus), 
this function may be excessive. This function should be used when the zoom 
adjustment is set to the full WIDE (wide-angle focus) whenever possible.
• When the horizontal lens shift is not set to the center, this function may not 
work well.
• Point at RETURN in the dialog with the ▲/▼ buttons and press ◄ or ENTER 
button to return to the GEOMETRY CORRECTION menu. NOTE
ASPECT
BLANKESC MENU
RESET
AUTOPAGEDOWN
ONOFFFREEZE
UP
ENTER
FOCUS- +ZOOM- +
INPUT
INTERACTIVE
MYBUTTON1
2PbyPMAGNIFYVOLUME-
+GEOMETRY PICTURE MUTE
NETWORK
OSD MSG
ASPECT
BLANK
ESC MENU
RESET
AUTO
PAGE
DOWN
ON
OFF
FREEZE
UP
ENTER
FOCUS
- +
ZOOM
- +
INPUT
INTERACTIVE
MYBUTTON1
2
PbyP
MAGNIFYVOLUME
-
+
GEOMETRYPICTURE MUTE
NETWORK
OSD MSGGEOMETRY
button 
						

							39
Operating
   
PERFECT FIT: 
When PERFECT FIT is pointed at, pressing the 
► or  ENTER  button displays the PERFECT FIT 
dialog. This projector is equipped with a test pattern for 
PERFECT FIT. Select PATTERN with the 
▲/▼ 
buttons, then press the 
◄/► buttons to switch on 
and off.
1.  Select SETUP with the ▲/▼ buttons and   
  press the ► or  ENTER button.
2.
 Select one of the corners or sides to be adjusted  
 
with the ▲/▼/◄/► buttons and press the  
ENTER  or 
 button.
3. Adjust the selected part as below. 
●   For adjusting a corner, use the ▲/▼/◄/► buttons to adjust the position of 
the corner.
●   For adjusting the upper or lower side, use the ▲/▼ buttons to adjust the 
distortion of the side.
●   For adjusting the left or right side, use the ◄/► buttons to adjust the 
distortion of the side.
●    To adjust another corner or side, press the  ENTER or 
 button and follow 
the procedure from step 2.
Correcting the distortion (continued)
(continued on next page) 
						

							40
Operating
Correcting the distortion (continued)
4. This projector is equipped with a memory feature for PERFECT FIT adjustment. Up to 3 sets of adjustments can be stored.
●   SAVE:   
To store the current PERFECT FIT adjustment, select one of the "SAVE" 
options numbered 1 to 3 (number of the memory) with the ▲/▼ buttons and 
press the ►,  ENTER or 
 button.  
Remember that the current data being stored of a memory will be lost by 
saving new data into the memory.
●   LOAD:   
To recall stored adjustments, select one of the "LOAD" options numbered 
1 to 3 (number of the memory) with the ▲/▼ buttons and press the ►, 
ENTER  or 
 button. 
Remember that the current adjusted condition will be lost by loading data. If 
you want to keep the current adjustment, please save it before performing a 
LOAD function.
• The LOAD functions whose linked memory has no data are skipped.
• There may be some noise and the screen may flicker for a moment when
loading data. This is not malfunction. NOTE
   WARPING: 
Projection on several types of screen can be performed by WARPING function. 
This function is operated by using dedicated PC tool, "Warping Tool". 
PC and projector are required to be connected with LAN cable in order to use 
this function. 
You can get the PC tool from the URL below.
    http://www.hitachi.co.jp/proj/
Refer to Application Manual for operations.