Hitachi Projector CP-WU5500 User Manual

							71
SETUP menu
ItemDescription
PICTURE 
POSITION Using the ▲/▼/◄/►
 cursor buttons selects the desirable picture 
position.
The PICTURE POSITION is not changed if any of the following
cases apply.
・  There is no non-display area (black display or background display) 
or it is not displayed on the screen.
• One of the following messages is displayed on the screen:
"NO INPUT IS DETECTED"
"SYNC IS OUT OF RANGE"
"INVALID SCAN FREQ."
• The BLANK or TEMPLATE function is selected.
INSTALLATION Pressing the ►button displays the dialog for changing the 
INSTALLATION setting.
  FRONT / DESKTOP
    
  REAR / DESKTOP
    
  REAR / CEILING
   
  FRONT / CEILING
Use the ▲/▼ buttons to select the desired setting on the 
INSTALLATION dialog, and press the  ENTER button of the remote 
control or the  INPUT button of the projector to execute.
If TRANSITION DETECTOR is ON and the INSTALLATION status 
is changed, the TRANSITION DETECTOR ON alarm (
99) will be 
displayed when the projector is restarted.
(continued on next page) 
						

							72
SETUP menu
ItemDescription
STANDBY MODE Using ▲/▼ buttons switches the standby mode setting between
NORMAL and SAVING.
NORMAL  ó SAVING
• When SAVING is selected, the RS-232C communication control 
except to turn the projector on and the network function are disabled 
while the projector is in the standby mode. If the COMMUNICATION 
TYPE in the COMMUNICATION menu is set to NETWORK 
BRIDGE, all of the RS-232C commands are disabled (
 90
).
• When SAVING is selected, STANDBY OUTPUT is invalid.
• When SAVING is selected, the HDMI Link and HDBaseT™ 
functions are disabled while the projector is in the standby mode.
• This function is available only when OFF is selected for STACK 
MODE. (
 OPTION menu > SERVICE > COMMUNICATION > 
STACK).
• When SAVING is selected, SCHEDULE function (Ex. POWER-
ON) at STANDBY MODE will not be operated.
• When SAVING is selected, the MHL STANDBY PWR. menu 
cannot be operated and MHL power feeding is unavailable with 
standby mode (
67).
COLOR 
UNIFORMITY Selects image level and region that are desired to be corrected, and 
adjusts Color Balance.
Divides the screen into 9 regions and adjusts gain of R/G/B of each 
region.
(continued on next page) 
						

							73
SETUP menu
ItemDescription
OSD MESSAGE Using the ▲/▼ buttons turns on/off the message function.
NORMAL  ó SILENT 
ó INHIBIT
 
  
 
■SILENT : The following message functions do not work.
“AUTO IN PROGRESS” while automatically adjusting.
“NO INPUT IS DETECTED”
“SYNC IS OUT OF RANGE”
“INVALID SCAN FREQ.”
“NOT AVAILABLE”
“Searching….” while searching for the input.
“Detecting….” while an input signal is detected.
The indication of the input signal displayed by changing.
The indication of the aspect ratio displayed by changing.
The indication of the PICTURE MODE displayed by changing.
The indication of the ACTIVE IRIS displayed by changing.
The indication of the MY MEMORY displayed by changing.
The indication of “FREEZE” and “II” while freezing the screen by 
pressing the  FREEZE button.
The indication of the TEMPLATE displayed by changing.
The indication of the ECO MODE displayed by changing.
■INHIBIT :  All message functions do not work.
The only buttons will function are as below.
STANDBY, ON
•   To change this function, follow the steps below. 
1. Press the  OSD MSG button on the remote control for 3 sec. 
2. The INHIBIT OSD will be displayed. While this OSD is displayed, press the  OSD MSG button again 
on the remote control.
3. Toggle and change the function.
  NORMAL  ó SILENT 
ó INHIBIT
 
  
(continued on next page) 
						

							74
SETUP menu
ItemDescription
HDMI OUTPUT
To select the image output on the HDMI OUT in the normal operation.
STANDBY  OUTPUT
AUDIO OUT
To select the sound output in the standby mode. 
MONITOR OUT
To select the image output on the MONITOR OUT in the standby mode.
HDMI OUT
To select the image output on the HDMI OUT in the standby mode.
•  When the STANDBY MODE is set to SAVING, the STANDBY 
OUTPUT menu can not be operated. 
						

							75
AUDIO menu
AUDIO menu
From the AUDIO menu, items shown in the table below 
can be performed. Select an item using the ▲/▼ cursor 
buttons, and press the ► cursor button or the ENTER 
button to execute the item. Then perform it according to 
the following table.
 
ItemDescription
VOLUME Using the ◄/► buttons adjusts the volume of the audio output.
Low  ó High
SPEAKER Using the ▲/▼ buttons turns on/off the built-in speaker.
ON  ó OFF
When OFF is selected, the built-in speaker does not work.
AUDIO SOURCE While the image signal from the input port chosen in step (1) is 
projected, the audio signal from the input port selected in step 
(2) is output to both the 
AUDIO OUT port and built-in speaker of 
this projector. However, the built-in speaker does not work when 
SPEAKER is set to OFF.
(1)   Choose a picture input port using the ▲/▼ buttons.
(2)  
Select an audio input port or the mute icon using the ◄/► buttons.The icons indicate the following;
No.1:  AUDIO IN1  port No.2: AUDIO IN2  port
No.3:  HDMI 1 / MHL  port No.4: HDMI 2  port
No.5:  HDBaseT  port  No.6: LAN port
 : mutes the sound
         
•  Audio input from port Nos.3 to 6 can only be selected by each of 
the picture input ports and AUDIO OUT STANDBY.
• C.C. (Closed Caption) is automatically activated when 
  is selected 
and an input signal containing C.C. is received. This function is 
available only when the signal is NTSC for  VIDEO or COMPUTER 
IN , and when AUTO is selected for DISPLAY in the C.C. menu under 
the SCREEN menu (
 81
). 
• For the setting of AUDIO OUT, refer to AUDIO OUT of STANDBY 
OUTPUT in the SETUP menu. 
CP-WU5505/CP-WX5505
CP-X5555 CP-WU5500/CP-WX5500
CP-X5550 
						

							76
SCREEN menu
SCREEN menu
From the SCREEN menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
ItemDescription
LANGUAGE Using the ▲/▼/◄/► buttons switches the OSD (On Screen 
Display) language.
ENGLISH  ó FRANÇAIS 
ó DEUTSCH 
ó  ESPAÑOL
       
   (shown in the LANGUAGE dialog)   
Press the 
ENTER or  button to save the language setting.
MENU POSITION Using the ▲/▼/◄/► buttons adjusts the menu position.
To quit the operation, press the 
MENU button on the remote control 
or keep no operation for about 10 seconds.
BLANK
Using the ▲/▼ buttons switches the mode for the blank screen.
The blank screen is a screen for the temporarily blanking feature 
(
 46
). It is displayed by pressing the  BLANK button on the remote 
control.
MyScreen  ó ORIGINAL 
ó BLUE 
ó WHITE 
ó BLACK
       
MyScreen :  Screen can be registered by the MyScreen item ( 78
).
ORIGINAL  :  Screen preset as the standard screen.
BLUE, WHITE, BLACK :   Plain screens in each color.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL
screen will change to the AUTO BLANK screen after several 
minutes.
(continued on next page) 
						

							77
SCREEN menu
ItemDescription
AUTO BLANK Using the ▲/▼ buttons switches the mode for the AUTO BLANK 
screen.
BLUE  ó WHITE 
ó BLACK
       
• To avoid remaining as an afterimage, displayed image will change
to the designated blank color screen by AUTO BLANK after several
minutes at the following conditions.
- When MyScreen or ORIGINAL is displayed as BLANK screen.
- When start-up screen is displayed.
START UP
Using the ▲/▼ buttons switches the mode for the start-up screen.
The start-up screen is a screen displayed when no signal or an 
unsuitable signal is detected. MyScreen  ó ORIGINAL 
ó OFF
       
MyScreen :  Screen can be registered by the MyScreen item ( 78
).
ORIGINAL  :  Screen preset as the standard screen.
OFF  :  Plain black screen.
• To avoid remaining as an afterimage, the START UP screen will 
change to the AUTO BLANK screen after several minutes. 
• When the ON is selected to the MyScreen PASSWORD item in 
the SECURITY menu (
 97
), the START UP is fixed to MyScreen.
(continued on next page) 
						

							78
SCREEN menu
ItemDescription
MyScreen This item allows you to capture an image for use as a MyScreen 
image which can be used as the BLANK screen and START UP 
screen. Display the image you want to capture before executing the 
following procedure.
(1)  
Selecting this item displays a dialog 
titled “MyScreen”. It will ask you if 
you start capturing an image from 
the current screen. Please wait for the target image to be displayed, and press the 
ENTER  or 
 button when the image is displayed. The image 
will freeze and the frame for capturing will appear. 
To stop performing, press the  RESET button on the remote 
control. 
(2)   Using the ▲/▼/◄/► buttons adjusts 
the frame position.  
Please move the frame to the position 
of the image which you want to use. The 
frame may not be able to be moved for 
some input signals.  
To start registration, press the  ENTER 
button on the remote control or  INPUT 
button on the control panel. To restore the screen and return to the previous dialog, press the 
RESET  button on the remote control or press the  ◄ and INPUT 
buttons at the same time on the control panel.  
Registration may take several minutes.  
When the registration is completed, the registered screen and 
the following message is displayed for several seconds:
“MyScreen registration is finished.”
If the registration failed, the following message is displayed: “A capturing error has occurred. Please try again.” 
• This function cannot be selected when the ON is selected to the 
MyScreen Lock item (
 79
).
• This function cannot be selected when the ON is selected to the 
MyScreen PASSWORD item in SECURITY menu (
 97
).
• This function is unavailable for a signal from the  LAN, HDMI 1/
MHL, HDMI 2 or  HDBaseT  port.
(continued on next page) 
						

							79
SCREEN menu
ItemDescription
MyScreen Lock Using the ▲/▼ buttons turns on/off the MyScreen lock function.
ON  ó OFF
When the ON is selected, the item MyScreen is locked. Use this 
function for protecting the current MyScreen.
• This function cannot be selected when the ON is selected to the 
MyScreen PASSWORD item in SECURITY menu (
 97
).
SOURCE NAME Each input port for this projector can have a name applied to it.
(1)  
Use the ▲/▼ buttons on the SCREEN menu to select SOURCE 
NAME and press the ► or  ENTER button.  
The SOURCE NAME menu will be displayed.
(2)   Use the ▲/▼ buttons on the SOURCE NAME menu to select 
the port to be named and press the ► button. The SOURCE 
NAME dialog will be displayed.  
Right side of the menu is blank until a name is specified.
(3)   Select an icon you would like to assign to 
the port in the SOURCE NAME dialog.   
The name assigned to the port will also be 
automatically switched according to your 
icon selection. Press  the ENTER  or 
 
button to determine your icon selection.
(4)   Select a number you would like to assign 
to the port along with the icon. You can 
select the number either from blank (no 
number assigned), 1, 2, 3, or 4.  
Then press the  ENTER or 
 button.
(5)   If you would like to modify the name   
assigned to the port, select CUSTOM NAME and press the 
ENTER  or 
 button. 
(continued on next page)
CP-WU5505/CP-WX5505 CP-X5555 CP-WU5500/CP-WX5500
CP-X5550
CP-WU5505/CP-WX5505CP-X5555 CP-WU5500/CP-WX5500
CP-X5550 
						

							80
SCREEN menu
ItemDescription
SOURCE NAME (continued )(6) 
 
The current name will be displayed 
on the first line. Use the ▲/▼/◄/► 
buttons and the  ENTER or 
 button to 
select and enter characters. To erase 1 
character at one time, press the  RESET 
button or press the ◄ and 
 button 
at the same time. Also if you move the 
cursor to DELETE or CLEAR ALL on 
screen and press the  ENTER or 
 
button, 1 character or all characters will 
be erased. The name can be a maximum 
of 16 characters.
(7)    To change an already inserted character, 
press the ▲ button to move the cursor to 
the first line, and use the ◄/► buttons to 
move the cursor on the character to be 
changed. 
After pressing the  ENTER or 
 button, the character is selected.  
Then, follow the same procedure as described at the item (6) 
above.
(8)    To finish entering text, move the cursor to the OK on screen 
and press the ►,  ENTER or 
 button. To revert to the previous 
name without saving changes, move the cursor to the CANCEL 
on screen and press the ◄,  ENTER or 
 button.
TEMPLATE Using the ▲/▼ cursor buttons switches the mode for the template 
screen.
Press the ► cursor (or the 
ENTER) button to display the selected 
template, and press the ◄ cursor button to close the displayed 
screen.
The last selected template is displayed when the  MY BUTTON
allocated to the TEMPLATE function is pressed (
 84
).
TEST PATTERN  ó DOT-LINE1 
ó DOT-LINE2 
ó DOT-LINE3
                                                                                          

STACK  ó 
MAP2 
ó MAP1 
ó CIRCLE2 
ó CIRCLE1 
ó DOT-LINE4
You can turn a map upside down and scroll it horizontally when 
MAP1 or MAP2 is selected. To invert or scroll the map, display 
the guidance by pressing the  RESET button on the remote three 
seconds or more when MAP1 or MAP2 appears.
(continued on next page)