Hitachi Projector CP-WU5500 User Manual

							91
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION (continued)
SERIAL SETTINGS
Select the serial communication condition for the 
CONTROL  port.
BAUD RATE 4800bps  ó 9600bps 
ó 19200bps 
ó 38400bps
      
  PARITY
NONE  ó ODD 
ó EVEN
    
• The BAUD RATE is fixed to 19200bps and PARITY 
is fixed NONE when the COMMUNICATION TYPE 
is set to OFF
 ( 90
).
TRANSMISSION METHOD
Select the transmission method for communication by 
the NETWORK BRIDGE from the  CONTROL port.
HALF-DUPLEX 
ó FULL-DUPLEX
HALF-DUPLEX : This method lets the projector 
make two way communication, but only one 
direction, either transmitting or receiving data, is 
allowed at a time.
FULL-DUPLEX : This method lets the projector 
make two way communication, transmitting and 
receiving data at the same time.
• HALF-DUPLEX is selected as the default setting.
• If you select HALF-DUPLEX, check the setting of 
the item RESPONSE LIMIT TIME  (
92
).
(continued on next page) 
						

							92
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION (continued)
RESPONSE LIMIT TIME
Select the time period to wait for receiving 
response data from other device communicating by 
the NETWORK BRIDGE and the HALF-DUPLEX 
through the  CONTROL port.
OFF  ó 1s 
ó 2s 
ó 3s
    
OFF : Select this mode if it is not required to check 
the responses from the device that the projector 
sends data to. In this mode, the projector can 
send out data from the computer continuously.
1s /2s /3s: Select the time period to keep the  projector waiting for response from the device 
that the projector sends data to. While waiting the 
response, the projector does not send out any 
data from the  CONTROL port.
• This menu is available only when the NETWORK 
BRIDGE is selected for the COMMUNICATION 
TYPE and the HALF-DUPLEX is selected for the 
TRANSMISSION METHOD  (
91
).
• OFF is selected as the default setting.
STACK
Selecting this item displays the STACK menu. 
For more information, please see  Instant Stack 
Guide . 
• When STACK MODE is set to MAIN or SUB, 
the other items in COMMUNICATION menu are 
invalid.
• When STACK MODE is set to MAIN or SUB, 
RS-232C menu of CONTROL TERMINAL cannot 
be set. The setting of RS-232C is forcibly set to 
CONTROL.
(continued on next page) 
						

							93
OPTION menu
ItemDescription
SERVICE
(continued) CONTROL 
TERMINAL * WIRED NETWORK
Selects whether to use 
LAN or HDBaseT  port.
      LAN  ó HDBaseT
RS-232C
Selects whether to use  CONTROL or HDBaseT  
port.
      CONTROL  ó HDBaseT
HDMI OUT 
RESOLUTION Selects the device to refer to the resolution 
information of HDMI output.
      
EXTERNAL DEVICE
 ⇔ PROJECTOR
・ When EXTERNAL DEVICE is selected, the 
resolution of the signal input to the projector and 
signal output from the projector may be restricted 
by the maximum resolution of the connected 
device such as projector or monitor.
・ When PROJECTOR is selected, the image from 
the device connected to HDMI OUT may not be 
displayed normally.
* CP-WU5505/CP-WX5505/CP-X5555 only
(continued on next page)
 • Only either LAN or HDBaseT  port 
can be used for the connection to the network. 
Switch it according to the environment.NOTE
 
• Only either CONTROL or HDBaseT  
port can be used for the RS-232C connection. 
Switch it according to the environment.NOTE 
						

							94
OPTION menu
ItemDescription
SERVICE
(continued) INFORMATION
Selecting this item displays a dialog titled “INPUT_INFORMATION”. 
It shows the information about the current input.
• The “FRAME LOCK” message on the dialog means the frame lock 
function is working. 
• This item cannot be selected for no signal and sync out.
• When the MY TEXT DISPLAY is set to ON, the MY TEXT is 
displayed together with the input information in the 
 
INPUT_INFORMATION box (
 101
).
FACTORY RESET
Selecting OK using the ► button performs this function. By this 
function, all the items in all of menus will collectively return to the 
initial setting. Note that the items LAMP TIME, FILTER TIME, 
LANGUAGE,  AUTO BLANK,  FILTER MESSAGE, STANDBY MODE, 
COMMUNICATION, NETWORK and SECURITY settings are not 
reset.
CANCEL  ð OK 
						

							95
NETWORK menu
See the Network Guide for details of NETWORK operation.
Remember that incorrect network settings on this projector may cause trouble on 
the network. Be sure to consult with your network administrator before connecting 
to an existing access point on your network.
NETWORK menu 
						

							96
SECURITY menu
This projector is equipped with security functions.
From the SECURITY menu, items shown in the table 
below can be performed.
To use SECURITY menu: User registration is required 
before using the security functions.
Enter to the SECURITY menu
1.  Press the ► button. The ENTER PASSWORD box will be displayed.
2.   Use the ▲/▼/◄/► buttons to enter the registered password. The 
factory default password is as follows.
   CP-WU5500/CP-WU5505  : 2905   CP-WX5500/CP-WX5505  : 1205
   CP-X5550/CP-X5555  : 2805
 This password can be changed 
( below
). Move the cursor to the 
right side of the ENTER PASSWORD box and press the ► button to 
display the SECURITY menu.
• It is strongly recommended the factory default password to be 
changed as soon as possible.
• If an incorrect password is input, the ENTER PASSWORD box  
will be displayed again. If incorrect password is input 3 times, the   
projector will turn off. Afterwards the projector will turn off every time an incorrect password is input.
3.   Items shown in the table below can be performed.
If you have forgotten your password(1)   While the ENTER PASSWORD box is displayed, press and hold the 
RESET  button on the remote control for about 3 seconds or press 
and hold the  INPUT button for 3 seconds while pressing the ► 
button on the projector.
(2)    The 10 digit Inquiring Code will be displayed. Contact your dealer 
with the 10 digit Inquiring Code. Your password will be sent after 
your user registration information is confirmed.
• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will 
close. If necessary, repeat the process from (1).  
Item Description
SECURITY 
PASSWORD  CHANGE
(1)    Use the ▲/▼ buttons on the SECURITY menu 
to select SECURITY PASSWORD CHANGE 
and press the ► button to display the ENTER 
NEW PASSWORD box.
(2)   Use the ▲/▼/◄/► buttons to enter the new password.
(3)    Move the cursor to the right side of the ENTER 
NEW PASSWORD box and press the ► button 
to display the NEW PASSWORD AGAIN box, 
enter the same password again. 
(4)  
Move the cursor to the right side of the NEW 
PASSWORD AGAIN box and press the ► 
button and the NOTE NEW PASSWORD box 
will be displayed for about 30 seconds, please 
make note of the password during this time.
Pressing the  ENTER button on the remote control or ► button on the 
projector will close the NOTE NEW PASSWORD box.
• Please do not forget your password.
(continued on next page)
SECURITY menu 
						

							97
SECURITY menu
ItemDescription
MyScreen 
PASSWORD
The MyScreen PASSWORD function can be used to prohibit access to the 
MyScreen function and prevent the currently registered MyScreen image 
from being overwritten.
1 Turning on the MyScreen PASSWORD1-1   Use the ▲/▼ buttons on the SECURITY menu to 
select MyScreen PASSWORD and press the ► 
button to display the MyScreen PASSWORD on/
off menu.
1-2   Use the ▲/▼ buttons on the MyScreen 
PASSWORD on/off menu to select ON. 
The ENTER NEW PASSWORD box (small) 
will be displayed.
1-3   Use the ▲/▼/◄/► buttons to enter the 
password. Move the cursor to the right side 
of the ENTER NEW PASSWORD box (small) 
and press the ► button to display the NEW 
PASSWORD AGAIN box, enter the same 
PASSWORD again.
1-4   Move the cursor to the right side of the 
NEW PASSWORD AGAIN box and press 
the ► button to display the NOTE NEW 
PASSWORD box for about 30 seconds, 
please make note of the password during 
this time.  Pressing the  ENTER button on the remote control or ► button on the 
projector will return to MyScreen PASSWORD on/off menu.
When a password is set for MyScreen:
• The MyScreen registration function (and menu) will be unavailable.
• The MyScreen Lock menu will be unavailable.
• The START UP setting will be locked on MyScreen (and the menu will be 
unavailable).
Turning the MyScreen PASSWORD off will allow normal operation of these 
functions.
• Please do not forget your MyScreen PASSWORD.
2 Turning off the MyScreen PASSWORD2-1   Follow the procedure in 1-1 to display the MyScreen  PASSWORD on/off 
menu.
2-2 
  Select OFF to display the ENTER 
PASSWORD box (large). Enter the registered 
password and the screen will return to the 
MyScreen PASSWORD on/off menu.
If an incorrect PASSWORD is input, the menu will 
close. If necessary, repeat the process from 2-1.
3 If you have forgotten your password3-1   Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off 
menu.
3-2   Select OFF to display the ENTER PASSWORD box (large). The 10 digit 
Inquiring Code will be displayed inside the box.
3-3   Contact your dealer with the 10 digit Inquiring Code. Your password will 
be sent after your user registration information is confirmed.
(continued on next page)
ENTER NEW PASSWORD  box (small)
ENTER PASSWORD box  (large) 
						

							98
SECURITY menu
ItemDescription
PIN LOCK
PIN LOCK is a function which prevents the projector from being used unless 
a registered Code is input.
1 Turning on the PIN LOCK1-1   Use the ▲/▼ buttons on the SECURITY menu 
to select PIN LOCK and press the ► button or 
the  ENTER  button to display the PIN LOCK on/off 
menu.
1-2   Use the ▲/▼ buttons on the PIN LOCK on/
off menu to select ON and the Enter PIN 
Code box will be displayed. 
1-3   Input a 4 part PIN code using the ▲/▼/◄/►   
or  INPUT  button. 
The PIN Code again box will appear. Reenter  
the same PIN code. This will complete the PIN 
code registration.
• If there is no key input for about 55 seconds   
while the Enter PIN Code box or the PIN Code again box is displayed, 
the menu will close. If necessary, repeat the process from 1-1.
Afterwards, anytime the projector is restarted after AC power is turned off 
the Enter PIN Code box will be displayed. Enter the registered PIN code.
The projector can be used after entering the registered PIN code. If an 
incorrect PIN code is input, the Enter PIN code box will be displayed again.
If an incorrect PIN code is input 3 times, the projector will turn of f. Afterwards 
the projector will turn off every time an incorrect PIN code is input. The 
projector will also turn off if there is no key input for about 5 minutes while 
the Enter PIN code box is displayed.
This function will activate only when the projector is started after  AC power 
is turned off.
• Please do not forget your PIN code.
2 Turning off the PIN LOCK2-1   Follow the procedure in 1-1 to display the PIN LOCK on/off menu. 
2-2   Use the ▲/▼ buttons to select OFF and the Enter PIN Code box will be 
displayed.  
Enter the registered PIN code to turn the PIN LOCK function off.
If an incorrect PIN code is input 3 times, the projector will turn of f. 
3 If you have forgotten your PIN code3-1  While the Enter PIN code box is displayed, press and hold the  RESET 
button for three seconds or press and hold the  INPUT button for 3 
seconds while pressing the ► button on the projector. 
The 10 digit Inquiring Code will be displayed.
• If there is no key input for about 5 minutes 
while the Inquiring Code is displayed, the 
projector will turn off.
3-2   Contact your dealer with the 10 digit Inquiring Code. Your PIN code will 
be sent after your user registration information is confirmed.
(continued on next page) 
						

							99
SECURITY menu
ItemDescription
TRANSITION  DETECTOR
If this function is set to ON and the vertical angle of 
the projector or the INSTALLATION setting is different 
from the previous recorded setting, the TRANSITION 
DETECTOR ON alarm will be displayed and the input 
signal will not be displayed.
• To display the signal again, set this function OFF.
• After about 5 minutes of displaying the TRANSITION DETECTOR ON 
alarm, the lamp will turn off.
1 Turning on the TRANSITION DETECTOR1-1   Use the ▲/▼ buttons on the SECURITY menu to 
select TRANSITION DETECTOR and press the ► 
or the  ENTER  button to display the TRANSITION 
DETECTOR on/off menu.
1-2  
Use the ▲/▼ buttons on the TRANSITION 
DETECTOR on/off menu to select ON. 
Selecting ON will save the setting of the 
current angle and the INSTALLATION setting. 
The ENTER NEW PASSWORD box (small) 
will be displayed.
1-3  Use the ▲/▼/◄/► buttons to enter a 
password. Move the cursor to the right side 
of the ENTER NEW PASSWORD box (small) 
and press the ► button to display the NEW 
PASSWORD AGAIN box, enter the same 
password again.
1-4   Move the cursor to the right side of the  
NEW PASSWORD AGAIN box and press  
the ► button to display the NOTE NEW  
PASSWORD box for about 30 seconds,  
please make note of the password during this time.
Pressing the  ENTER button on the remote control or the ► button on the 
projector will return to the TRANSITION DETECTOR on/off menu.
• Please do not forget your TRANSITION DETECTOR password.
• This function will activate only when the projector is started after turning off 
the AC power.
• This feature may not function properly if the projector is not in a stable 
position when ON is selected.
2 Turning off the TRANSITION DETECTOR2-1  Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.2-2  Select OFF to display the ENTER 
PASSWORD box (large). Enter the registered 
password and the screen will return to the 
TRANSITION DETECTOR on/off menu.
If an incorrect password is input, the menu will 
close. If necessary, repeat the process from 2-1.
3 If you have forgotten your password3-1  Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.3-2   Select OFF to display the ENTER PASSWORD box (large). The 10 digit 
Inquiring Code will be displayed inside the box.
3-3   Contact your dealer with the 10 digit Inquiring Code. Your password will 
be sent after your user registration information is confirmed.
(continued on next page)
ENTER NEW PASSWORD  box (small)
ENTER PASSWORD box  (large) 
						

							100
SECURITY menu
ItemDescription
MY TEXT 
PASSWORD
The MY TEXT PASSWORD function can prevent the MY TEXT from being 
overwritten. When the password is set for the MY TEXT;
• The MY TEXT DISPLAY menu will be unavailable, which can prohibit 
changing the DISPLAY setting.
• The MY TEXT WRITING menu will be unavailable, which can prevent the 
MY TEXT from being overwritten.
1 Turning on the MY TEXT PASSWORD1-1   Use the ▲/▼ buttons on the SECURITY menu to 
select the MY TEXT PASSWORD and press the 
► button to display the MY TEXT PASSWORD 
on/off menu.
1-2   Use the ▲/▼ buttons on the MY TEXT 
PASSWORD on/off menu to select ON. The 
ENTER NEW PASSWORD box (small) will 
be displayed.
1-3   Use the ▲/▼/◄/► buttons to enter the 
password. Move the cursor to the right side 
of the ENTER NEW PASSWORD box (small) 
and press the ► button to display the NEW 
PASSWORD AGAIN box, and then enter the 
same password again.
1-4   Move the cursor to the right side of the NEW 
PASSWORD AGAIN box and press ► button 
to display the NOTE NEW PASSWORD box 
for about 30 seconds, then please make note 
of the password during this time.
Pressing the  ENTER button on the remote control or ► button on the 
projector will return to the MY TEXT PASSWORD on/off menu. 
2 Turning off the MY TEXT PASSWORD2-1   Follow the procedure in 1-1 to display  
the MY TEXT PASSWORD on/off menu.
2-2   Select OFF to display the ENTER 
PASSWORD box (large). Enter the registered 
password and the screen will return to the 
MY TEXT PASSWORD on/off menu. 
If an incorrect password is input, the menu will close. 
If necessary, repeat the process from 2-1
3 If you have forgotten your password3-1   Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off 
menu.
3-2   Select OFF to display the ENTER PASSWORD box (large). The 10 digit 
inquiring code will be displayed inside the box. 
3-3   Contact your dealer with the 10 digit inquiring code. Your password will 
be sent after your user registration information is confirmed.
(continued on next page)
ENTER NEW PASSWORD   box (small)
ENTER PASSWORD box  (large)