Hitachi Projector CP-HD9950 User Manual

91
OPTION menu
ItemDescription
SERVICE(continued)COMMUNICATION
Selecting this item displays COMMUNICATION menu. In this menu, you can configure the serial communication settings of the projector using the CONTROL port.
• Select an item using the cursor buttons ▲/▼. Then pressing the ► button opens the submenu for the setting item you selected. Or, pressing the ◄ button instead of the ► button makes the menu back to the previous one without changing the setup. Each submenu can be operated as described...

92
OPTION menu
ItemDescription
SERVICE(continued)COMMUNICATION(continued)
SERIAL SETTINGS
Select the serial communication condition for the CONTROL port.
BAUD RATE
4800bps  9600bps  19200bps  38400bps      
 PARITY
NONE  ODD  EVEN    
• The BAUD RATE is fixed to 19200bps and PARITY is fixed NONE when the COMMUNICATION TYPE 
is set to OFF (91).
TRANSMISSION METHOD
Select the transmission method for communication by the NETWORK BRIDGE from the CONTROL port.
HALF-DUPLEX  FULL-DUPLEX
HALF-DUPLEX: This...

93
OPTION menu
ItemDescription
SERVICE(continued)COMMUNICATION(continued)
RESPONSE LIMIT TIME
Select the time period to wait for receiving response data from other device communicating by the NETWORK BRIDGE and the HALF-DUPLEX through the CONTROL port.
OFF  1s  2s  3s    
OFF: Select this mode if it is not required to check the responses from the device that the projector sends data to. In this mode, the projector can send out data from the computer continuously.
1s /2s /3s: Select the time period to...

94
OPTION menu
ItemDescription
SERVICE(continued)
INFORMATION
Selecting this item displays a dialog titled “INPUT INFORMATION”. It shows the information about the current input.
• The “FRAME LOCK” message on the dialog means the frame lock function is working. • This item cannot be selected for no signal and sync out.• When the MY TEXT DISPLAY is set to ON, the MY TEXT is displayed together with the input information in the  
INPUT INFORMATION box (100).
FACTORY RESET
Selecting OK using the ► button...

95
NETWORK menu
See the Network Guide for details of NETWORK operation.
Remember that incorrect network settings on this projector may cause trouble 
on the network. Consult with your network administrator before connecting to an 
existing access point on your network.
NETWORK menu 

96
Security
ItemDescription
SECURITY PASSWORD CHANGE
(1)  Use the ▲/▼ buttons on the SECURITY menu to select SECURITY PASSWORD CHANGE and press the ► button to display the ENTER NEW PASSWORD box.(2)  Use the ▲/▼/◄/► buttons to enter the new password.(3)  Move the cursor to the right side of the ENTER NEW PASSWORD box and press the ► button to display the NEW PASSWORD AGAIN box, enter the same password again. (4)  Move the cursor to the right side of the NEW PASSWORD AGAIN box and press the ► button and...

97
Security
ItemDescription
MyScreen PASSWORD
The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten.
1 Turning on the MyScreen PASSWORD1-1  Use the ▲/▼ buttons on the SECURITY menu to select MyScreen PASSWORD and press the ► button to display the MyScreen PASSWORD on/off menu.1-2  Use the ▲/▼ buttons on the MyScreen PASSWORD on/off menu to select ON. The ENTER NEW PASSWORD box (small) will be...

98
Security
ItemDescription
PIN LOCK
PIN LOCK is a function which prevents the projector from being used unless a registered Code is input.
1 Turning on the PIN LOCK1-1  Use the ▲/▼ buttons on the SECURITY menu to select PIN LOCK and press the ► button or the ENTER button to display the PIN LOCK on/off menu.1-2  Use the ▲/▼ buttons on the PIN LOCK on/off menu to select ON and the Enter PIN Code box will be displayed. 1-3  Input a 4 part PIN code using the ▲/▼/◄/►, COMPUTER 1 or INPUT button. The PIN Code...

99
Security
ItemDescription
MY TEXT PASSWORD
The MY TEXT PASSWORD function can prevent the MY TEXT from being overwritten. When the password is set for the MY TEXT;• The MY TEXT DISPLAY menu will be unavailable, which can prohibit changing the DISPLAY setting.• The MY TEXT WRITING menu will be unavailable, which can prevent the MY TEXT from being overwritten.
1 Turning on the MY TEXT PASSWORD1-1  Use the ▲/▼ buttons on the SECURITY menu to select the MY TEXT PASSWORD and press the ► button to display the...

100
Security
ItemDescription
MY TEXT DISPLAY
(1)  Use the ▲/▼ buttons on the SECURITY menu to select the MY TEXT DISPLAY and press the ► or ENTER button to display the MY TEXT DISPLAY on/off menu.
(2)  Use the ▲/▼ buttons on the MY TEXT DISPLAY on/off menu to select on or off.
ON  OFF
When it is set ON, the MY TEXT will be displayed on the START UP screen and the INPUT INFORMATION when the INFORMATION on the SERVICE menu is chosen.
• This function is available only when the MY TEXT PASSWORD function is...