Hitachi Projector CP-BW301Wn User Manual

41
INPUT menu
ItemDescription
VIDEO FORMAT The video format for 
VIDEO IN port can be set.
 
Using the ◄/► buttons switches 
the mode for video format.
AUTO   ó  NTSC  
ó  PAL  
ó  SECAM
      N-PAL  ó M-PAL 
ó NTSC4.43 
• 
This item is performed only for a video signal from the  VIDEO IN port.• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well for some signals. If the 
picture becomes unstable (e.g. an irregular picture, lack of color), 
please select the mode...

42
INPUT menu
ItemDescription
COMPUTER IN The computer input signal type for 
COMPUTER IN1 and IN2 ports 
can be set.
(1) Use the ▲/▼ buttons to select the  COMPUTER IN port to be 
set.
(2)   Use the ◄/► buttons to select   
the computer input signal type.
(COMPUTER IN1)
AUTO  ó SYNC ON G OFF
(COMPUTER IN2)
AUTO  ó SYNC ON G OFF 
ó MONITOR OUT
• Selecting the AUTO mode allows you to input a sync on G signal
or component video signal from the port (
 13
).
• In the AUTO mode, the picture may be distorted...

43
INPUT menu
ItemDescription
RESOLUTION The resolution for the 
COMPUTER IN1 and COMPUTER IN2  input 
signals can be set on this projector.
(1)   In the INPUT menu select the RESOLUTION using the ▲/▼ 
buttons and press the ► button. 
The RESOLUTION menu will be   
displayed.
(2)   In the RESOLUTION menu select the 
resolution you wish to display using 
the ▲/▼ buttons.   
Selecting AUTO will set a resolution 
appropriate to the input signal.
(3)   Pressing the ► or  ENTER button when 
selecting a...

44
SETUP menu
SETUP menu
From the SETUP menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
ItemDescription
D-ZOOM Using the ◄/► cursor buttons adjusts the magnification ratio.
Small  ó Large
• The on-screen menu might be displayed outside of the image 
display area depending on the adjustment value of the ASPECT, 
D-ZOOM and 
 KEYSTONE....

45
SETUP menu
ItemDescription
PICT. POSIT. H
(CP-BW301WN)Using the ▲/▼ cursor buttons selects the horizontal picture
position.
LEFT  ó MID 
ó RIGHT
The PICT. POSIT. H is not changed if any of the following cases 
apply.
• The ASPECT is set to 16:9 or 16:10.
• The input signal has an aspect ratio of 16:9, 16:10 or verticallly
smaller than 16:10, while ASPECT is set to NORMAL.
• Horizontal size of the displayed image is full on the effective
display area, while the ASPECT is set to NATIVE.
• One of the...

46
SETUP menu
(continued on next page)
ItemDescription
LAMP &  FILTER AUTO ECO 
MODE Using the ▲/▼
 buttons turns on/off the AUTO ECO MODE.
ON  ó OFF
• When ON is selected, the projector will always be set to Eco-
2 mode at start-up regardless of the ECO MODE (
 46
) setting. 
An OSD message “AUTO ECO MODE” will be displayed for 
tens of seconds when the projector starts with this function 
activated.
ECO MODE Using the ▲/▼
 buttons switches the ECO MODE.
   OFF  ó ECO-1 
ó ECO-2INTELLIGENT ECO 
óSAVER...

47
SETUP menu
ItemDescription
LAMP &  FILTER LAMP TIME
The lamp time is the usage time of the lamp, counted after the 
last resetting. 
Pressing the 
RESET button on the remote control or the ► 
button of the projector displays a dialog. 
To reset the lamp time, select the OK using the ► button.
CANCEL  ð OK
• Please reset the lamp time only when you have replaced the 
lamp, for a suitable indication about the lamp.
• For the lamp replacement, see the section "Replacing the 
lamp" (
 96
).
• The...

48
SETUP menu
ItemDescription
IMAGE
OPTIMIZER When this function is enabled, automatic image correction
is performed to maintain visibility in accordance with lamp
deterioration.
• This function may not work properly when HDCR/
ACCENTUALIZER is set to other than 0.
• This function does not work properly unless LAMP TIME is
initialized when replacing a lamp.
INSTALLATION Pressing the ►button displays the dialog for changing the 
INSTALLATION setting.
Use the ▲/▼ buttons to select the desired setting on...

49
SETUP menu
ItemDescription
STANDBY MODE Using ▲/▼ buttons switches the standby mode setting between 
NORMAL and SAVING. 
NORMAL  ó SAVING
When SAVING is selected, the power consumption in the standby 
mode is lowered with some functional restriction as below:
• When SAVING is selected, the RS-232C communication control 
except to turn the projector on and the network function are disabled 
while the projector is in the standby mode. If the COMMUNICATION 
TYPE in the COMMUNICATION menu is set to...

50
AUDIO menu
AUDIO menu
From the AUDIO menu, items shown in the table below 
can be performed. Select an item using the ▲/▼ cursor 
buttons, and press the ► cursor button or the ENTER 
button to execute the item. Then perform it according to 
the following table.
ItemDescription
VOLUME Using the ◄/► buttons adjusts the volume.
Low  ó High
SPEAKER Using the ▲/▼ buttons turns on/off the built-in speaker.
ON  ó OFF
When OFF is selected, the built-in speaker does not work.
AUDIO SOURCE While the image...