Hitachi Projector CP-A222WN User Manual

							61
OPTION menu
Item Description
MY BUTTONThis item is to assign one of the following functions to MY BUTTON 
1/2 on the remote control (
6).
(1)  Use the ▲/▼ buttons on the MY BUTTON menu to select a MY 
BUTTON - (1/2) and press the ► or ENTER button to display the 
MY BUTTON setup dialog. 
(2)  Then using the ▲/▼/◄/► buttons sets one of the following 
functions to the chosen button. Press the ENTER or INPUT 
button to save the setting.
• LAN: Selects input from LAN port.
• USB TYPE A: Selects input from USB TYPE A port.
• USB TYPE B: Selects input from USB TYPE B port.
• HDMI: Selects input from HDMI port.
• COMPUTER IN1: Selects the input from COMPUTER IN1 port.
• COMPUTER IN2: Selects the input from COMPUTER IN2 port.
• S-VIDEO: Selects the input from S-VIDEO port.
• VIDEO: Selects the input from VIDEO port.
•  SLIDESHOW: Selects the input from USB TYPE A port, and starts 
a Slideshow.
•  MY IMAGE: Displays the MY IMAGE menu (
79).
•  MESSENGER: 
Turns the messenger text displayed on the screen on/off 
(Messenger Function in the User's Manual - Network Guide). 
When there is no transferred text data to display, the message 
”NO MESSENGER DATA" appears.
•  INFORMATION: Displays SYSTEM_INFORMATION,  
INPUT_INFORMATION (
70), WIRELESS INFORMATION 
(
75), WIRED INFORMATION (77) or nothing.
•  MY MEMORY: Loads one of adjustment data stored (
36). 
When more than one data are saved, the adjustment  
changes every time the MY BUTTON is pressed.
When no data is saved in memory, the 
dialog "No saved data" appears.
When the current adjustment is not 
saved to memory, the dialog as shown in 
the right appears.
If you want to keep the current adjustment, please press  
the ► button to exit. Otherwise loading a data will overwrite the 
current adjusted condition.
(continued on next page) 
						

							62
OPTION menu
Item Description
MY BUTTON
(Continued)•  ACTIVE IRIS: Changes the active iris mode.
• PICTURE MODE: Changes the PICTURE MODE (
33).
•  
FILTER RESET: Displays the filter time reset confirmation dialogue (60).
•  TEMPLATE: Makes the template pattern selected to the 
TEMPLATE item (
56) appear or disappear.
•  AV MUTE: Turns the picture and audio on/off.
•  D-ZOOM: Turns the D-ZOOM mode on/off. When the D-ZOOM 
mode is on, use the ◄/► cursor buttons to adjust the 
magnification ratio.
•  D-SHIFT: Turns the D-SHIFT mode on/off. When the D-SHIFT 
mode is on, use the ▲/▼/◄/► cursor buttons to move the 
magnifying area.
•  RESOLUTION: Turns on/off the RESOLUTION dialog (
43).
•  MIC VOLUME: Turns  on/off the MIC VOLUME dialog (
51).
•  ECO MODE: Turns on/off the ECO MODE (
47).
•  SAVER MODE: Turns on/off the SAVER MODE (
47).
MY SOURCEUsing ▲/▼ buttons selects the picture input port to be selected with 
pressing the MY SOURCE/DOC.CAMERA button on the remote 
control.
You can use this function not only for document cameras but also 
computers and other equipment.
COMPUTER IN1 
 COMPUTER IN2 
 LAN 
 USB TYPE A
            VIDEO 
 S-VIDEO 
 HDMI 
 USB TYPE B
(continued on next page) 
						

							63
OPTION menu
Item Description
SERVICESelecting this item displays the SERVICE 
menu.
Select an item using the ▲/▼ buttons, and 
press the ► button or the ENTER button 
on the remote control to execute the item.
ALTITUDE
Using the ▲/▼ buttons switches the rotation speed of the cooling 
fans. If the projector is used at an altitude of about 1600 m or higher, 
select HIGH. Otherwise, select NORMAL. Note that the projector is 
noisier when the HIGH is selected.
HIGH 
 NORMAL
AUTO ADJUST
Using the ▲/▼ buttons to select one of the mode. When the 
DISABLE is selected, the automatic adjustment feature is disabled.
FINE 
 FAST 
 DISABLE
   
FINE: Finer tuning including H.SIZE adjustment.
FAST:  Faster tuning, setting H.SIZE to prearranged data for the 
input signal.
• Depending on conditions, such as input image, signal cable to 
the projector, environment around the projector, etc., the automatic 
adjustment may not work correctly.  In such a case, please 
choose DISABLE to disable the automatic adjustment, and make 
adjustment manually.
GHOST
Adjust the settings using the ▲/▼ buttons to eliminate ghosting.
FILTER MESSAGE
Use the ▲/▼ button to set the timer for notifying by the message 
when to replace the filter unit 
100h 
 • • • 
 5000h 
 OFF
After choosing an item except OFF, the message “REMINDER *** 
HRS PASSED ....” will appear after the timer reaches the interval 
time set by this feature (
11 3). 
When the OFF is chosen, the message will not appear. Utilize this 
feature to keep the air filter clean, setting the suitable time according 
to your environment of this projector.
• Please take care of the filter unit periodically, even if there is 
no message. If the air filter becomes to be blocked by dust or 
other matter, the internal temperature will rise, which could cause 
malfunction, or reduce the lifetime of the projector.
• Please be careful with the operating environment of the projector 
and the condition of the filter unit.
(continued on next page) 
						

							64
OPTION menu
Item Description
SERVICE
(continued)KEY LOCK
(1)  Use the ▲/▼ buttons to select CONTROL PANEL or REMOTE 
CONTROL.
(2) Use the ◄/► buttons to turn the key lock function on/off.
When ON is selected, all buttons on the projector or remote control 
except the STANDBY/ON button are locked.
• Please use this function to prevent tampering or accidental 
operation. 
• It is not possible to set both CONTROL PANEL and REMOTE 
CONTROL to ON.
LENS DOOR LOCK
Use the ▲/▼ cursor buttons to turn on/off the LENS DOOR LOCK 
function. Set LENS DOOR LOCK to ON to keep the lens door open 
even when power is turned off. Follow cautions below when you set 
LENS DOOR LOCK to ON and keep the lens door open all the time.
• Do not apply excessive force on or allow impact to the lens door, 
as it incorporates a mirror.
• Keep the projector out of the reach of children.
• Never touch a lens door or mirror. If the mirror is broken, the 
projected image will be distorted. Close the lens door, and contact 
your dealer.
When the LENS DOOR LOCK is set to ON and the lens door is 
not open completely for some reason, the image may shift or have 
keystone distortion. In that case use the LENS DOOR OPEN 
function (
below) to open the lens door completely.
LENS DOOR OPEN
Use the LENS DOOR OPEN function to open the lens door if not 
open completely for some reason such as cleaning.
LENS DOOR CLOSE
Use the LENS DOOR CLOSE function to temporarily close the lens 
door when LENS DOOR LOCK is set to ON. Note that the lamp will 
be turned off when the lens door is closed. Press the STANDBY/ON 
button on the projector or the remote control to open the lens door 
and start the projector again.
(continued on next page) 
						

							65
OPTION menu
Item Description
SERVICE
(continued)REMOTE FREQ.
(1)  Use the ▲/▼ button to change the projector's remote sensor 
frequency setting (
17, 18).
1:NORMAL 
 2:HIGH
(2)  Use the ◄/► button to change the 
projector's remote sensor on or off.
ON 
 OFF
The factory default setting is for both 1:NORMAL and 2:HIGH to be 
on. If the remote control does not function correctly, disable either of 
them.
It's not possible to disable both options at the same time.
COMMUNICATION
Selecting this item displays COMMUNICATION 
menu. 
In this menu, you can configure the serial 
communication settings of the projector using the 
CONTROL port.
• Select an item using the cursor buttons ▲/▼. 
Then pressing the ► button opens the submenu 
for the setting item you selected. Or, pressing 
the ◄ button instead of the ► button makes the 
menu back to the previous one without changing 
the setup. Each submenu can be operated as 
described above.
• When COMMUNICATION TYPE (
66)
 is set to 
OFF, the other items in COMMUNICATION menu 
are invalid. 
• For the function of serial communication, refer to 
the User's Manual - Network Guide.
(continued on next page) 
						

							66
OPTION menu
Item Description
SERVICE
(continued)
COMMUNICATION
(continued)
COMMUNICATION TYPE
Select the communication type for transmission via 
the CONTROL port.
NETWORK BRIDGE: 
Select this type, if it is required 
to control an external device as a network terminal, 
via this projector from the computer. 
The CONTROL port doesn't accept RS-232C  
commands (
Network Bridge Function in the 
User’s Manual - Network Guide
)
OFF: Select this mode to receive RS-232C 
commands using the CONTROL port. 
• 
OFF is selected as the default setting. 
• When you select the NETWORK BRIDGE, check 
the item, TRANSMISSTION METHOD (
below)
.
SERIAL SETTINGS
Select the serial communication condition for the 
CONTROL port.
BAUD RATE
4800bps 
 9600bps 
 19200bps 
 38400bps
      
 PARITY
NONE 
 ODD 
 EVEN
    
• The BAUD RATE is fixed to 19200bps and PARITY 
is fixed NONE when the COMMUNICATION TYPE 
is set to OFF
 (above)
.
TRANSMISSION METHOD
Select the transmission method for communication by 
the NETWORK BRIDGE from the CONTROL port.
HALF-DUPLEX 
 FULL-DUPLEX
HALF-DUPLEX: This method lets the projector 
make two way communication, but only one 
direction, either transmitting or receiving data, is 
allowed at a time.
FULL-DUPLEX: This method lets the projector 
make two way communication, transmitting and 
receiving data at the same time.
• HALF-DUPLEX is selected as the default setting.
• If you select HALF-DUPLEX, check the setting of 
the item RESPONSE LIMIT TIME (
67)
.
(continued on next page) 
						

							67
OPTION menu
Item Description
SERVICE
(continued)
COMMUNICATION
(continued)
RESPONSE LIMIT TIME
Select the time period to wait for receiving 
response data from other device communicating by 
the NETWORK BRIDGE and the HALF-DUPLEX 
through the CONTROL port.
OFF 
 1s 
 2s 
 3s
    
OFF: Select this mode if it is not required to check 
the responses from the device that the projector 
sends data to. In this mode, the projector can 
send out data from the computer continuously.
1s /2s /3s: Select the time period to keep the 
projector waiting for response from the device 
that the projector sends data to. While waiting the 
response, the projector does not send out any 
data from the CONTROL port.
• This menu is available only when the NETWORK 
BRIDGE is selected for the COMMUNICATION 
TYPE and the HALF-DUPLEX is selected for the 
TRANSMISSION METHOD (
66).
• OFF is selected as the default setting.
CLONING
The setttings of the projector can be coppied via USB 
memory.
SAVE:  Saves each settings of the projector to USB 
memory.
LOAD: 
Loads each settings of the projector from 
USB memory. Message will be displayed 
after loading, and power will turn off after five 
min. or by pressing ► button. (A message is 
displayed for a few seconds if loading fails.)
After saving / loading, you can remove the USB 
storage device.
(continued on next page) 
						

							68
OPTION menu
Item Description
SERVICE
(continued)
CLONING
(continued)
The following items are exempted.
OPTION: LAMP TIME, FILTER TIME, 
SERVICE(GHOST)
NETWORK: WIRELESS AND WIRED SETUP
(IP ADDRESS, SUBNET MASK, 
DEFAULT GATEWAY, DATE AND 
TIME), MY IMAGE, PRESENTATION
SECURITY: MY TEXT DISPLAY
• Operation is not available if SECURITY_
CLONNING LOCK is turned ON.
• The Screen_MyScreen can only be loaded.
CLONING load function on STANDBY MODE
• While the projector is in STANDBY MODE, push 
the INPUT button of control panel together with ► 
button, and then press ▲ button to start operating 
the CLONING load function.
• During loading process, the three indicators of 
control panel (POWER (orange), TEMP, LAMP) 
will remain on.
•  After the loading process, the three indicators 
(POWER (orange), TEMP, LAMP) will turn off. 
Then, you can remove the USB storage device.
•  If the loading fails, the three indicators (POWER 
(orange), TEMP, LAMP) will blink at the same 
time.
• CLONING is invalid with the following conditions.
- CLONING LOCK is turned ON. 
   With this condition, the three indicators (POWER 
(orange), TEMP, LAMP) will blink at approximately 
three seconds intervals.
- If the STANDBY MODE is set to SAVING.
-  If there is no USB memory inserted into USB 
TYPE A  port.
-  If PIN LOCK or lock of TRANSITION DETECTOR 
is not being released.
- If a system error occurs.
• Please operate one of the following after loading.
-  Press INPUT button and 
◄ button of the control 
panel  at the same time.
- Wait at least five min. after loading. 
-  Restart the projector after re-plugging the AC 
cable.
(continued on next page) 
						

							69
OPTION menu
Item Description
SERVICE
(continued)
CLONING
(continued)
Load MyScreen data
•  Please save the image data as "pj_logo.bmp" or 
"pj_logo.gif" into USB memory.
•  Please note that the only compatible formats are 
as follows.
-File format
Windows BMP   bit/pixel: 2/4/8/15/16/24/32bit
Compression format : 
Without compression/RLE
GIF
-Image size: more than 36x36, less than 1280x800
•  If two kinds of file format are saved, "pj_logo.
bmp" will be registered into MyScreen data.
•  If MyScreen LOCK or MyScreen PASSWORD 
is turned ON, the data of MyScreen cannot be 
loaded.
Setting the data
•  Operating the SAVE function under CLONING 
will name the file as "pj_data.bin" into the USB 
memory. Please do not attempt to change the file 
name or the folder structure.
•  If a file with the same name already exists, it will 
be overwritten by operating the SAVE function.
Loading function
•  Please note that saved data from other model 
cannot be loaded.
•  
Please note that, if any of the following functions: 
MyScreen PASSWORD, PIN LOCK, TRANSITION 
DETECTOR, MY TEXT PASSWORD under 
SECURITY menu or MyScreen Lock under 
SCREEN menu is ON, the respective saved data 
cannot be loaded.
  
(continued on next page) 
						

							70
OPTION menu
Item Description
SERVICE
(continued)
CLONING
(continued)
Loading function (continued)
•  Please note that the saved data of KEYSTONE 
under SETUP menu cannot be loaded if 
TRANSITION DETECTOR under SECURITY 
menu is ON.
•  
Please note that the saved data of START UP 
and MyScreen Lock under SCREEN menu cannot 
be loaded if  MyScreen PASSWORD under 
SECURITY menu is ON.
•  Please note that the saved data of MY TEXT 
WRITING cannot be loaded if MY TEXT 
PASSWORD under SECURITY menu is ON.
INFORMATION
Selecting this item displays a dialog titled “INPUT_INFORMATION”. 
It shows the information about the current input.
• The “FRAME LOCK” message on the dialog means the frame lock 
function is working. 
• This item can't be selected for no signal and sync out.
• When the MY TEXT DISPLAY is set to ON, the MY TEXT is 
displayed together with the input information in the INPUT_
INFORMATION box (
87).
FACTORY RESET
Selecting OK using the ► button performs this function. By this 
function, all the items in all of menus will collectively return to the 
initial setting. Note that the items LAMP TIME, FILTER TIME, 
LANGUAGE, FILTER MESSAGE, NETWORK and SECURITY 
settings are not reset.
CANCEL 
 OK
Be sure to set ALTITUDE after resetting all the settings (
63).