Hitachi Projector CP-A222WN User Manual

							21
Power on/off
►Be careful not to pinch your finger with the lens door, to 
prevent an injury.
►Do not touch around the lamp cover and the exhaust vents during use or just 
after use, since it is too hot.
►Remove the power cord for complete separation. The power outlet should be 
close to the projector and easily accessible.WARNING
1.Press the STANDBY/ON button on the projector or the remote control.  
The message “Power off?” will appear on the screen for about 5 seconds.
Turning off  the power
2.Confirm that there is nothing that the lens door hits while closing. 
Press the STANDBY/ON button again while the message appears.  
The projector lamp will go off, and the POWER indicator will begin blinking in 
orange. The lens door will close right after the lamp goes off.
However, to maintain better picture quality, the lens door will close after the 
lamp has been cooled down when the projector is installed upside down such 
as in ceiling mount installation. Then POWER indicator will stop blinking and 
light in steady orange when the lamp cooling is complete (
11 4).
Do not turn the projector on for about 10 minutes or more after turning it off. 
Also, do not turn the projector off shortly after turning it on. Such operations might 
cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.
• Turn the power on/off in right order. Please power on the projector 
prior to the connected devices. 
• 
This projector has the function that can make the projector automatically turn on/
off. Please refer to the DIRECT POWER ON 
(58) and AUTO POWER OFF (59) 
items of the OPTION menu.
NOTE 
						

							22
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME

FOCUS
D-ZOOM
Operating
Operating
1.
Adjusting the volume
Use the VOLUME +/VOLUME - buttons to adjust the volume. 
A dialog will appear on the screen to aid you in adjusting the 
volume. If you do not do anything, the dialog will automatically 
disappear after about ten seconds.
●  When  is selected for current picture input port, the volume adjustment is 
disabled. Please see AUDIO SOURCE item of AUDIO menu (
50).
●  Even if the projector is in the standby mode, the volume is adjustable when 
both of the following conditions are true:
-  An option other than 
 is selected for STANDBY in the AUDIO SOURCE 
item of the AUDIO menu
 (
50).
- 
NORMAL is selected in the STANDBY MODE item of the SETUP menu (48).
●  In the standby mode, the volume of the microphone is adjustable with the  
VOLUME +/- buttons on the remote control, in synchronization with the volume 
of the projector 
(
12).
1.Press MUTE button on the remote control.  
A dialog will appear on the screen indicating that you have muted 
the sound.  
To restore the sound, press the  MUTE, VOLUME + or 
VOLUME - button. Even if you do not do anything, the dialog 
will automatically disappear after about ten seconds.
Temporarily muting the sound
●  When  is selected for current picture input port, the sound is always muted. 
Please see AUDIO SOURCE item of AUDIO menu (
50).
●  C.C. (Closed Caption) is automatically activated when sound is muted and an 
input signal containing C.C. is received. This function is available only when 
the signal is NTSC for VIDEO or S-VIDEO, or 480i@60 for COMPUTER IN1 
or COMPUTER IN2, and when AUTO is selected for DISPLAY in the C.C. 
menu under the SCREEN menu (
57).
1.Press INPUT button on the projector.  
Each time you press the button, the projector 
switches its input port from the current port as below.
Selecting an input signal
(continued on next page)
●  While ON is selected for AUTO SEARCH item in OPTION menu (58), the projector 
will keep checking the ports in above order repeatedly till an input signal is detected.
● It may take several seconds to project the images from the USB TYPE B port.
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME

VOLUME +/- button
MUTE button
                COMPUTER IN1  COMPUTER IN2  
    VIDEO                                                             LAN
    S-VIDEO                                           USB TYPE A
                
    HDMI      
  
USB TYPE B
INPUT button 
						

							23
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME

FOCUS
D-ZOOM
Operating
1.Press VIDEO button on the remote control.  
Each time you press the button, the projector switches its 
input port from the current port as below. Selecting an input signal (continued)
●   While ON is selected for AUTO SEARCH item in OPTION 
menu, the projector will keep checking every port sequentially 
till an input signal is detected (
58). If VIDEO button is 
pressed when COMPUTER IN1, COMPUTER IN2, LAN, USB 
TYPE A or USB TYPE B port is selected, the projector will 
check HDMI port first. 
1.Press COMPUTER button on the remote control.  
Each time you press the button, the projector switches its 
input port from the current port as below.
●  While ON is selected for AUTO SEARCH item in OPTION 
menu, the projector will keep checking every port sequentially 
till an input signal is detected (
58). If COMPUTER button is 
pressed when VIDEO, S-VIDEO or HDMI port is selected, the 
projector will check COMPUTER IN1 port first.
●   
It may take several seconds to project the images from the 
USB TYPE B port.
1.Press the MY SOURCE / DOC. CAMERA button on 
the remote control. The input signal will be changed 
into the signal you set as MY SOURCE (
62).
●  This function also can use for document camera. Select the 
input port that connected the document camera.
         COMPUTER IN1  COMPUTER IN2  LAN
               USB TYPE B    
    USB TYPE A
        HDMI   S-VIDEO  
                 VIDEO 
VIDEO button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME

FOCUS
D-ZOOM
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME

FOCUS
D-ZOOM
MY SOURCE /  
DOC. CAMERA button
COMPUTER button 
						

							24
1.Press ASPECT button on the remote control.   
Each time you press the button, the projector switches the 
mode for aspect ratio in turn. 
Selecting an aspect ratio
● ASPECT button does not work when no proper signal is inputted.
● NORMAL mode keeps the original aspect ratio setting.
● 
The on-screen menu might be displayed outside of the image display area 
depending on the adjustment value of the ASPECT, D-ZOOM, 
 KEYSTONE  
and 
 KEYSTONE. Changing the values of ASPECT, D-ZOOM,  
 KEYSTONE and  KEYSTONE may fix the symptom.
1.Press SEARCH button on the remote control.
The projector will start to check its input ports as below in 
order to find any input signals.
When an input is found, the projector will stop searching 
and display the image. If no signal is found, the projector will 
return to the state selected before the operation.
Searching an input signal
●  While ON is selected for AUTO SEARCH item in OPTION menu (58), the 
projector will keep checking the ports in above order repeatedly till an input 
signal is detected.
●  
It may take several seconds to project the images from the USB TYPE B port.
  For a computer signal 
NORMAL  4:3  16:9  16:10  NATIVE 
     
  For a video signal, s-video signal or component video signal 
4:3  16:9  16:10  14:9  NATIVE 
 
   For an input signal from the LAN, USB TYPE A or USB TYPE B port, or 
if there is no signal  
CP-A222WN, CP-A302WN: 4:3 (fixed)  
CP-AW252WN: 16:10 (fixed)
Operating
  For an HDMITM signal 
NORMAL  4:3  16:9  16:10  14:9  NATIVE 
     
ASPECT button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME

FOCUS
D-ZOOM
                COMPUTER IN1  COMPUTER IN2  
    VIDEO                                                             LAN
    S-VIDEO                                           USB TYPE A
                
    HDMI      
  
USB TYPE B
SEARCH button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME

FOCUS
D-ZOOM
 
						

							25
Operating
Adjusting the zoom and focus Adjusting the projector's elevator
The projector has Front foot for inclinations and Rear foot for horizontals. Spacers 
on the each elevator foot are installed at the time of shipment, and projector is in a 
condition to be able to just project. If necessary, detach the spacer, and the elevator 
feet can be manually twisted to make more precise adjustments.
Front footRear foot
2.3~4.3°
-1~1° Front foot
Rear footSpacer
Spacer (Large)
Spacer (Small)
Press the D-ZOOM + or D-ZOOM - button on the remote 
control to display D-ZOOM dialog on screen.
Use the D-ZOOM + and D-ZOOM - buttons to adjust the 
picture size.
To finish the operation, do not touch these buttons for about 
ten seconds until the dialog is disappeared.
● If you want to expand a part of the image, use the magnify 
function (
28).
►Keep the spacers away from children and pets. Be careful not 
to let them swallow the spacers. If swallowed consult a physician immediately 
for emergency treatment.WARNING
• The adjustment angle can be adjusted up to plus or minus 1° each of 
FRONT and REAR foot.
• 
After the foot is adjusted, it is possible to return it to the state of the shipment with a spacer. 
Install Large on the Front foot and Small on the Rear foot of the spacer. If change 
the setting place of the projector, it will recommend keep and reuse the spacers.
NOTE
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
POSITIONMENU
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME

FOCUS
D-ZOOM
D-ZOOM + button D-ZOOM - button
(continued on next page) 
						

							26
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
POSITIONMENU
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME

FOCUS
D-ZOOM
Operating
1.
Press AUTO button on the remote control.  
Pressing this button performs the following.
Using the automatic adjustment feature
  For a computer signal 
The vertical position, the horizontal position and the horizontal 
phase will be automatically adjusted.  
Make sure that the application window is set to its maximum size 
prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
  For a video signal and s-video signal 
The video format best suited for the respective input signal will be selected 
automatically. This function is available only when the AUTO is selected for 
the VIDEO FORMAT item in the INPUT menu (
41). The vertical position and 
horizontal position will be automatically set to the default.
●  The automatic adjustment operation requires approx. 10 seconds. Also please 
note that it may not function correctly with some input. 
●  When this function is performed for a video signal, a certain extra such as a line 
may appear outside a picture.
●  When this function is performed for a computer signal, a black frame may be 
displayed on the edge of the screen, depending on the PC model. 
●  
The items adjusted by this function may vary when the FINE or DISABLE is selected 
for the AUTO ADJUST item of the SERVICE item in the OPTION menu (
63).
   For a component video signal  
The vertical position and horizontal position will be automatically set to the default. 
The horizontal phase will be automatically adjusted.
AUTO button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME

FOCUS
D-ZOOM
Press the FOCUS + or FOCUS - button on the remote 
control, or FOCUS + or FOCUS - button on the projector 
(5) 
while no menu is on screen, to display the FOCUS box on 
screen. Use the FOCUS + and FOCUS - buttons to adjust 
the screen focus. After the focus adjustment, wait for a while 
until the FOCUS box is disappeared, if you want to display 
any other menu on screen by pushing the MENU button on 
the projector.
● The ◄/►/▲/▼ buttons on the projector work only as the 
cursor buttons while the template is displayed 
(56).
● FOCUS +/- button on the projector is invalid when the USB 
TYPE A port is selected as the input source.
FOCUS + button FOCUS - button 
						

							27
POSITION
ESCMENU
RESET
ENTER1.
Press the POSITION button on the remote control while no menu 
is on screen, to display the D-SHIFT 
(44) dialog on screen.
Adjusting the position
2.
Use the ▲, ▼, ◄ and ► buttons to adjust the picture position.
Press the POSITION button again to finish this operation.
●  This is a function to shift the position of the shrunken picture by the D-ZOOM 
(44) 
function.
●  When an OSD (On Screen Display) menu is displayed, this operation moves the 
position of the OSD menu, but not the position of the picture  
(31).
●  The D-SHIFT adjustment values are not valid when the D-ZOOM is set to 256 (full 
screen). 
(CP-A222WN, CP-A302WN)
●  The D-SHIFT adjustment values are not valid when the D-ZOOM is set to 320 (full 
screen). 
(CP-AW252WN)
Operating
1.Press KEYSTONE button on the remote 
control. A dialog will appear on the screen 
to aid you in correcting the distortion.
Correcting the keystone distortions
2.Use the ▲/▼ cursor buttons to select MANUAL or PERFECT 
FIT operation, and press the ► button to perform the following.
(1)  MANUAL displays a dialog for keystone correction.  
Use the ▲/▼ buttons to select  KEYSTONE /  
 KEYSTONE, then use the ◄/► buttons for 
adjustment.
(2)  
PERFECT FIT displays a dialog for adjusting the shape 
of the projected image in each of the corners and sides.
To close the dialog and complete this operation, press 
KEYSTONE button again. Even if you do not do anything, the 
dialog will automatically disappear after about ten seconds.
●  The adjustable range of this function will vary among inputs. For some input, 
this function may not work well.
●  This function will be unavailable when TRANSITION DETECTOR is on (
85).
POSITION button
KEYSTONE button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME

FOCUS
D-ZOOM
 
						

							28
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME

Operating
1.
Using the magnify feature
2.
3.
4.
Press the MAGNIFY ON button on the remote control.  
The picture will be magnified, and the MAGNIFY dialog will 
appear on the screen. When the MAGNIFY ON button is 
pressed for the first time after the projector is turned on, the 
picture will be zoomed by 1.5 times. On the dialog, triangle 
marks to show each direction will be displayed.
The display magnification of the projector switches in order  
with every press of the MAGNIFY ON button.
  For computer signals, HDMI
TM (RGB) signals, input signals from the 
LAN, USB TYPE A or USB TYPE B port
      1.5 times  2 times  3 times  4 times  1 time 
  
For video signals, s-video signals, component video signals or HDMITM 
(Component) signals
      1.5 times  2 times   1 time 
While the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor 
buttons to shift the magnifying area.
Press the MAGNIFY OFF button on the remote control to exit magnification.
●  The MAGNIFY dialog will automatically disappear in several seconds with no 
operation. The dialog will appear again if the MAGNIFY ON button is pressed 
when the dialog has automatically disappeared.
●  The magnification is automatically disabled when the displaying signal or its 
display condition is changed.
●  While the magnification is active, the keystone distortion condition may vary. 
It will be restored when the magnification is disabled.
●  Some horizontal stripes might be visible on the image while magnification is 
active.
●  This function is not available in the following cases: 
-  A sync signal in the range not supported is input.
-  There is no input signal.
MAGNIFY
ON/OFF button 
						

							29
Operating
1.Press BLANK button on the remote control.  
The BLANK screen will be displayed instead of the screen of 
input signal. Please refer to BLANK item in SCREEN menu 
(
52).
To exit from the BLANK screen and return to the input signal 
screen, press BLANK button again. 
Temporarily blanking the screen
●  The projector automatically exits from the BLANK mode when 
some control buttons are pressed.
• The sound is not connected with the BLANK screen function. If 
necessary, set the volume or mute first. To display the BLANK screen and mute 
the sound at one time, use AV MUTE function 
(62). NOTE
1.Press the FREEZE button on the remote control.  
The “FREEZE” indication will appear on the screen (however, 
the indication will not appear when the OFF is selected for 
the MESSAGE item in the SCREEN menu (
54)), and the 
projector will go into the FREEZE mode, which the picture is 
frozen.
To exit the FREEZE mode and restore the screen to normal, 
press the FREEZE button again. 
Temporarily freezing the screen
●  The projector automatically exits from the FREEZE mode when some control 
buttons are pressed.
●  If the projector continues projecting a still image for a long time, the LCD 
panel might possibly be burned in. Do not leave the projector in the FREEZE 
mode for too long.
●  Images might appear degraded when this function is operated, but it is not a 
malfunction.
►If you wish to have a blank screen while the projector’s lamp 
is on, use the BLANK function above.
Taking any other action may cause the damage on the projector.CAUTION
FREEZE button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME

FOCUS
D-ZOOM
BLANK button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
o
9×VOLUME

FOCUS
D-ZOOM
 
						

							30
POSITION
ESCMENU
RESET
ENTER
Operating
1.To start the MENU, press the MENU button. The MENU you last used (EASY 
or ADVANCED) will appear. EASY MENU has priority to appear just after 
powered on.
Using the menu function
2.
(1)  Use the ▲/▼ cursor buttons to select an item to 
operate. If you want to change it to the ADVANCED 
MENU, select the ADVANCED MENU.
(2)  Use the ◄/► cursor buttons to operate the item. This projector has the following menus:  
PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK, 
SECURITY and EASY MENU.  
EASY MENU consists of functions often used, and the other menus are classified 
into each purpose and brought together as the ADVANCED MENU.
Each of these menus is operated using the same methods. While the projector 
is displaying any menu, the MENU button on the projector works as the cursor 
buttons. The basic operations of these menus are as follows.
In the EASY MENU
(continued on next page)(1)  Use the ▲/▼ cursor buttons to select a menu. 
If you want to change it to the EASY MENU, 
select the EASY MENU. 
The items in the menu appear on the right side.
(2)  Press the ► cursor button or ENTER button to  
move the cursor to the right side. Then use the  
▲/▼ cursor buttons to select an item to operate and press the ► cursor 
button or ENTER button to progress. The operation menu or dialog of the 
selected item will appear.
(3)  Use the buttons as instructed in the OSD to operate the item.
In the ADVANCED MENU
MENU button 
(Cursor buttons)
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCH
BLANK
MUTE
MY BUTTON
POSITION
ESCMENU
RESET
COMPUTERMY SOURCE/AUTOMAGNIFYPAGEDOWNONOFFFREEZEUPo9×VOLUME

ENTER
FOCUS
D-ZOOM
RESET button ENTER buttonMENU button
Cursor buttons
ESC button