Hitachi L37x01a Users Manual

10
COMPONENT NAMES
Main Unit
Front Panel
Rear Panel
Control Panel (including side input) 
1  Sub Power button
2  Channel Down/
zbutton
3  Channel Up/
xbutton
4  Volume Down/
{button
5  Volume Up/
ybutton
6  Input Select/OK button
7  Menu/Return button
8  Side Input 1  Cabinet
2  Panel
3  Remote control receiver
4  Indicating Lamp
5  Desktop Stand
6  Main Power Switch (on the bottom surface)
7  Speaker
1  Terminal board (External Device Connection)
2  Power Cord Socket
3  Handgrips
Please refer to
14 ~22...

11
ENGLISH
COMPONENT NAMES (Continued)
Remote Control
NOTE
The function indicated by [  ] are only for Teletext 
mode. Refer to
57,58.
1Sub Power23
2  Device Select (TV/DTT, DVD, SAT)27,73
     Press these buttons to select device mode. The selected 
button blinks once. Normally, select “TV/DTT”.
3
Programme Select/Input Mode [Page Select] 25,27,
57,58
     Press these buttons to select a TV programme directly.
You can also use these buttons when changing the Input 
mode.
4  Freeze/Multi Mode [Hold]...

12
PREPARATION
This remote control operates on 2 “AA” batteries.
1.Open the batter y compartment cover
 Slide open the battery compartment 
  cover on the backside in the 
direction of an arrow, and remove 
the cover.
CAUTION
It could cause corrosion or batter y leakage and may result in physical injur y 
and/or property damage including fi re.  
 Never mix used and new batteries in the device.  
 Replace all the batteries in a device at the same time.
 Remove the batteries if the remote control is not...

13
ENGLISH
PREPARATION (continued)
Safety Precaution on Main Unit Installation
Read SAFETY PRECAUTIONS (4to7) carefully besides this page. 
*The Desktop Stand has been used for the illustration in this manual.
Anti-Tumble Measures
Install in a stable place and implement safety measure against overturning.When installing the main unit, be sure to use the specifi ed mount units in order to obtain maximum performance 
and maintain the safety.
We assume no responsibility or liability for personal injuries or...

14
CONNECTION
Terminal Positions
1
1  Power Cord Socket
2 Aerial Socket
3 AV 1
4 AV 2
5 AV 3
6 AV 4
7 Monitor Out
8  Service Use only
9  Service Use only
0Power Swivel Terminal
!Optical Out (Digital Audio)
@HDMI 2
# HDMI 3
$  Common interface slot
% PC Terminal
^Mini stereo for Audio
& Sub Woofer
* Headphone terminal
( AV 5
) HDMI 1
q Photo Input Terminal
w  SD Memory Card slot
#
0%
6
9
3
4
5
!&
^
827
@$
*
(
)
q
w
 

15
ENGLISH
Connecting Procedure
This unit is ready for various kinds of connections. Make a connection in the following steps. Be sure to turn off the 
Main Power fi rst when connecting external equipments.
1. Connect Power Cord to the rear panel.
2. Connect Aerial Lead.
3. Connect your external equipments to the unit if any. 
4. Connect the Power Plug to the Wall Socket.
1. Connecting Power Cord to the Rear Panel
Connect Power Cord to the unit.
*Make sure not to connect the Power Plug to the Wall Socket...

16
3. Connecting to External Equipment
 Terminals on Rear
AV 1 can be connected to the equipment with Composite/S-Video/Audio output, and Composite/Audio input.
The output signalcan support not only Analogue but also Digital Terrestrial TV signals.
INPUT    Composite/S-Video/Audio
 If STB is connected to AV1 in France, it descrambles some of the Pay TV images by resending the signal again (In/Out).
OUTPUT    Composite/Audio
While View Timer is on, the active programme is output from AV1. See 53 for View...

17
ENGLISH
AV 4 can be connected to the equipment with either Component or Composite output. When using as Composite, do 
not insert the jacks into P
B or PR.
 If your external device has a Component terminal, COMPONENT connection is recommended for higher quality 
picture
.
Monitor Out can be used to display same image as main unit on another monitor.
When this output terminal is connected to an external monitor with a 75 Ohm terminal, the same image from 
composite (AV1~5), or RF signal can be...

18
HDMI 2 and 3terminal can be connected to the devices with HDMI output. If the external device has DVI output, this can 
be available with HDMI-DVI cable. In case of using the HDMI-DVI cable, connect to audio terminal besides HDMI input 
terminal.
Refer to 20 about HDMI1 terminal on side.
Information
HDMI (High Defi nition Multimedia Interface) is next-generation multimedia I/O interface. Only one cable is used to 
transmit all video/audio/control signals, which creates easy connection.
Moreover, those...

19
ENGLISH
PC terminal (D-sub 15 pin) is connected to PC, which allows Analogue RGB signal. Connect to also audio terminal 
on the rear besides PC (RGB) terminal.
Sub Woofer terminal can bring the deep bass sound from the external speaker equipped with a built-in amplifi er.
 Terminals on Side
Since the following terminals are located on the side, it is very convenient to connect an extra device on a temporary 
basis after completing the connections on the rear panel. 
Headphone
In case of setting...