Hitachi Cp-X608 Projector Users Manual



Setting up
NOTE  • Be sure to read the manuals for devices before connecting them to\
 the 
projector, and make sure that all the devices are suitable to be connected with t\
his 
product. Before connecting to a PC, check the signal level, the signal t\
iming, and the 
resolution.
-  Do not connect LAN port to any network that might have the excessive vol\
tage.
-  Some signal may need an adapter to input this projector.
-  Some PCs have multiple screen display modes that may include some...



Setting up
Inserting an SD card and USB memor y
When using the projector with a wireless LAN please insert the included \
wireless 
network card. When using a commercial SD memory card in order to view im\
ages 
insert the SD memory card in the same manner. And when using a commercial 
USB memory in order to view images insert the USB memory to the AUX I/O port.
See the “User's Manual - Network Function” for information on usin\
g either type of 
card.
. Make sure the projector’s...

3

Setting up
How to use the slot cover lock
. Open the slot cover lock, and insert it into the 
locking a slot.
. Close the slot cover lock slowly, and attach a 
padlock  or  combination  lock  to  the  slot  cover 
lock.
Connecting power supply
. Connect the connector of the power cord to the AC inlet of the projector.
. Firmly plug the power cord's plug into the outlet. 
AC inlet
to the outlet
Connector of the power cord
SD CARDSD CARD
WARNING  ►Please use extra caution...

4

Remote control
Putting batteries
Please load the batteries before using the remote control. If the remote\
 control starts to 
malfunction, replace the batteries. If you will not use the remote contr\
ol for an extended 
period, remove the batteries from the remote control and store them in a\
 safe place.
. Slide back and remove the 
battery cover in the direction 
of the arrow.
. Align and insert the two AA 
batteries according to their 
plus and minus   terminals as indicated in the...

5

Changing the frequency of  remote control signal
The accessory remote control has the choice of the mode  or the mode  , in the frequency of its signal. If  the  remote  control  does  not  function  properly, attempt to change the signal frequency.Please  remember  that  the  “REMOTE  FREQ.”  in SERVICE  item  of  OPTION  menu (47)  of  the 
projector to be controlled should be set to the same mode as the remote control.To  set  the  mode  of  the  remote  control,  slide  the knob...

6
Using as a wired remote control
The accessory remote control works as a wired remote control, when the wired control port at the bottom of the remote control connects with the REMOTE CONTROL port on the back of the projector via an audio cable with 3.5 diameter stereo mini plugs. When the remote control signal is hard to reach surely to the projector in the environment, this function is effective.
Remote control
NOTE  • To connect the remote control with the projector, use an audio cable with...

7
Power on/off
WARNING  ►A strong light is emitted when the projector’s power is on. Do not look into 
the lens of the projector or look inside of the projector through any of\
 the projector’s openings.
►Do not touch around the lamp cover and the exhaust vents during use or j\
ust after use, since it is too hot.
NOTE  • Turn the power on/off in right order. Please power on the projector prior 
to the connected devices. Power off the projector later than the connected devices.
• Before turning the...

8

Operating
Operating
Adjusting the volume
. Press the VOLUME button on the remote control. 
A dialog will appear on the screen to aid you in adjusting the volume.
. Use the cursor buttons ▲/▼ to adjust the volume.
To close the dialog and complete the operation, press the 
VOLUME button again. Even if you do not do anything, the 
dialog will automatically disappear after a few seconds.
● When no audio port is selected for current picture input port, the volume 
adjustment is disable....

9

Operating
Searching an input signal
. Press the SEARCH button on the remote control.
The projector will start to check its input ports in order to 
find any input signals.
When an input is found, the projector will stop searching and display th\
e image. 
If no signal is found, the projector will return to the state selected b\
efore the 
operation.
RGB   RGB    M -D  MIU  COMPONENT (Y, CB/RB, CR/BR)  S-VIDEO  VIDEO 
   
●   
The MIU input is skipped, as long as no...

0

Adjusting the zoom and focus
. Use the zoom ring to adjust the screen size.  
. Use the focus ring to focus the picture.
Operating
Focus ringZoom ring
Adjusting the lens shift
. Use the vertical lens shift dial to shift 
the picture upward or downward.  
. Use the horizontal lens shift dial to 
shift the picture left or right.
Using the automatic adjustment feature
. Press the AUTO button on the remote control.  
 For an RGB or MIU signal 
The vertical position, the...