Hitachi Cp-X2510n Projector Users Manual

							51
NETWORK menu
Remember that incorrect network settings on this 
projector may cause trouble on the network. Be sure 
to consult with your network administrator before 
connecting to an existing access point on your 
network.
Select “NETWORK” from the main menu to access 
the following functions. 
Select an item using the ▲/▼ cursor buttons on the projector or remote control, 
and press the ► cursor button on the projector or remote control, or ENTER 
button on the remote control to execute the item. Then perform it according to the 
following table.
See the User’s Manual - Network Guide  for details of NETWORK operation.
NETWORK menu
• If you are not utilizing SNTP (Date/Time Settings of the User’s 
Manual - Network Guide) , then you must set the DATE AND TIME during the 
initial installation.
• The network communication control is disabled while the projector is in 
standby mode if the STANDBY MODE item of SETUP menu is set to SAVING. 
Please connect the network communication to the projector after setting the 
STANDBY MODE to NORMAL (
36).
NOTE
Item
Description
SETUP Selecting this item displays the SETUP 
Menu for the network.
Use the ▲/▼ buttons to select an item, 
and the ► or ENTER button on the remote 
control to perform the item.
DHCP  
(Dynamic Host  Configuration  Protocol) Use the ▲/▼ buttons to turn DHCP on/off.
ON  ó OFF
Select OFF when the network does not have 
DHCP enabled.
• When the “DHCP” setting changes to “ON”, it 
takes a little time to obtain IP address from DHCP 
server.
• Auto IP function will be assigned an IP address if 
the projector could not obtain an IP address from 
server even if DHCP is “ON”.
(continued on next page) 
						

							52
NETWORK menu
ItemDescription
SETUP
(continued) IP ADDRESS
Use the ▲/▼
/◄/► buttons to enter the IP 
ADDRESS. 
This function can only be used when DHCP is set 
to OFF.
• The IP ADDRESS is the number that identifies 
this projector on the network. You cannot have two 
devices with the same IP ADDRESS on the same 
network.
• The IP ADDRESS “0.0.0.0” is prohibited.
SUBNET  MASK Use the ▲/▼
/◄/► buttons to enter the same 
SUBNET MASK used by your computer. 
This function can only be used when DHCP is set 
to OFF.
•  The SUBNET MASK ”0.0.0.0” is prohibited.
DEFAULT 
GATEWAY Use the ▲/▼
/◄/► buttons to enter the DEFAULT 
GATEWAY (a node on a computer network that 
serves as an access point to another network) 
address.
This function can only be used when DHCP is set 
to OFF.
DNS SERVER Use the ▲/▼/◄/► buttons to input the DNS 
server address. 
The DNS server is a system to control domain 
names and IP addresses on the Network. 
TIME 
DIFFERENCE Use the ▲/▼
 buttons to enter the TIME 
DIFFERENCE. 
Set the same TIME DIFFERENCE as the one 
set on your computer. If unsure, consult your IT 
manager. 
Use the ► button to return to the menu after 
setting the TIME DIFFERENCE.
DATE AND  TIME Use the ▲/▼
/◄/► buttons to enter the Year (last 
two digits), Month, Date, Hour and Minute.
• The projector will override this setting and retrieve 
DATE AND TIME information from the Time server 
when SNTP is enabled.  (
 Date/Time Settings 
of the User’s Manual - Network Guide)
(continued on next page) 
						

							53
NETWORK menu
ItemDescription
PROJECTOR  NAME (1)  
Use the ▲/▼ buttons on the 
NETWORK menu to select the 
PROJECTOR NAME and press 
the ► button. The PROJECTOR 
NAME dialog will be displayed.
(2)    The current PROJECTOR NAME will be displayed on the first 3 
lines. If not yet written, the lines will be blank.
Use the ▲/▼/◄/► buttons and the  ENTER or INPUT button to 
select and enter characters.
To erase 1 character at one time, press the  RESET button or 
press the ◄ and INPUT button at the same time.  Also if you 
move the cursor to DELETE or ALL CLEAR on screen and 
push the ENTER or INPUT button, 1 character or all characters 
will be erased.The PROJECTOR NAME can be input up to 64 
characters.
(3)    To change an already inserted 
character, press the ▲/▼ button 
to move the cursor to one of the 
first 3 lines, and use the ◄/► 
buttons to move the cursor on the 
character to be changed. After 
pressing the  ENTER or INPUT 
button, the character is selected. 
Then, follow the same procedure 
as described at the item (2) above.
(4)    To finish entering text, move the cursor to the OK on screen and 
press the ►,  ENTER or INPUT button. To revert to the previous 
PROJECTOR NAME without saving changes, move the cursor 
to the CANCEL on screen and press the ◄, ENTER or INPUT 
button.
(continued on next page) 
						

							54
NETWORK menu
ItemDescription
MY IMAGE Selecting this item displays the 
MY 
IMAGE menu. 
The application software “PJImage” 
is required to store image(s) into the 
projector.
Use the ▲/▼ buttons to select an item which is a still image by the 
MY IMAGE  (
 MY IMAGE (Still Image Transfer) Display of the 
User’s Manual - Network Guide)  and the ► or ENTER button to 
display the image.
• The item without image stored cannot be selected.
• The image names are each displayed in 16 characters or less.
To switch the image displayed  Use the ▲/▼ buttons.
To return to the menu Press the ◄ button on the remote control.
To erase the image displayed and its source file in the projector.(1)   Press the RESET button on the 
remote control while displaying an 
image to display the MY IMAGE 
DELETE menu. 
(2)   Press the ► button to perform to erase. 
To stop erasing, press the ◄ button.
AMX D.D.
(AMX Device  Discovery)
Use the ▲/▼ buttons to turn the AMX Device Discovery on/off.
ON  ó OFF
When ON is selected, the projector can be detected by  controllers 
of AMX connected to the same network. For the details of AMX 
Device Discovery, visit the AMX web site. URL: http://www.amx.com/
(continued on next page) 
						

							55
NETWORK menu
ItemDescription
INFORMATION Selecting this item displays the NETWORK_INFORMATION dialog 
for confirming the network settings.
• Only the first 16 characters of the projector neme are displayed.
• Nothing (blank) is shown in the “PROJECTOR NAME” field until 
you setup the item (
53).
• When the voltage level of the battery for the built in clock 
decreases, the set time may become incorrect even though accurate 
date and time are input. Replace the battery suitably
 (66).
• IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY indicate 
“0.0.0.0” when DHCP is ON and the projector has not gotten 
address from DHCP server.
SERVICE Executing this item restarts and initializes the network functions.
 
Choose the RESTART EXECUTE using the button ►.
Then use the button ► to execute.
Network will be once cut off when choose restart.  
If DHCP is selected on, IP address may be changed.  
After selecting RESTART EXECUTE, NETWORK menu may not be 
controlled approx. 30 seconds. 
						

							56
SECURITY menu
This projector is equipped with security functions.
From the SECURITY menu, items shown in the table 
below can be performed.
To use SECURITY menu: User registration is required 
before using the security functions.
Enter the SECURITY menu
1.  Use the ▲/▼ buttons on the SECURITY menu to select ENTER PASSWORD and press the ► 
button. The ENTER PASSWORD box will be displayed.  
2.   Use the ▲/▼/◄/► buttons to enter the registered password. The 
factory default password is  9676. This password can be changed 
(below). Move the cursor to the right side of the ENTER 
PASSWORD box and press the ► button to display the SECURITY 
menu.
• It is strongly recommended the factory default password to be 
changed as soon as possible.
• If an incorrect password is input, the ENTER PASSWORD box 
will be displayed again. If incorrect password is input 3 times, the 
projector will turn off. Afterwards the projector will turn off every time 
an incorrect password is input.
3.   Items shown in the table below can be performed.
If you have forgotten your password(1).   While the ENTER PASSWORD box is displayed, press and hold 
the RESET button on the remote control for about 3 seconds or 
press and hold the  INPUT button for 3 seconds while pressing the 
► button on the projector.
(2).    The 10 digit Inquiring Code will be displayed. Contact your dealer 
with the 10 digit Inquiring Code. Your password will be sent after 
your user registration information is confirmed.
• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will 
close. If necessary, repeat the process from (1).  
Item Description
SECURITY 
PASSWORD  CHANGE
(1)   Use the ▲/▼ buttons on the SECURITY menu 
to select SECURITY PASSWORD CHANGE 
and press the ► button to display the ENTER 
NEW PASSWORD box.
(2)   Use the ▲/▼/◄/► buttons to enter the new password.
(3)   Move the cursor to the right side of the 
ENTER NEW PASSWORD box and press the 
► button to display the NEW PASSWORD 
AGAIN box, enter the same password again. 
(4)  
Move the cursor to the right side of the NEW 
PASSWORD AGAIN box and press the ► 
button and the NOTE NEW PASSWORD box 
will be displayed for about 30 seconds, please 
make note of the password during this time.
Pressing the ENTER button on the remote control or ► button on the 
projector will close the NOTE NEW PASSWORD box.
• Please do not forget your password.
SECURITY menu
(continued on next page) 
						

							57
SECURITY menu
ItemDescription
MyScreen 
PASSWORD
The MyScreen PASSWORD function can be used to prohibit access to the 
MyScreen function and prevent the currently registered MyScreen image 
from being overwritten.
1 Turning on the MyScreen PASSWORD1-1   Use the ▲/▼ buttons on the SECURITY menu to 
select MyScreen PASSWORD and press the ► 
button to display the MyScreen PASSWORD on/
off menu.
1-2   Use the ▲/▼ buttons on the MyScreen 
PASSWORD on/off menu to select ON. 
The ENTER NEW PASSWORD box (small) 
will be displayed.
1-3   Use the ▲/▼/◄/► buttons to enter the 
password. Move the cursor to the right side 
of the ENTER NEW PASSWORD box (small) 
and press the ► button to display the NEW 
PASSWORD AGAIN box, enter the same 
PASSWORD again.
1-4   Move the cursor to the right side of the 
NEW PASSWORD AGAIN box and press 
the ► button to display the NOTE NEW 
PASSWORD box for about 30 seconds, 
please make note of the password during 
this time. 
Pressing the ENTER button on the remote control or ► button on the 
projector will return to MyScreen PASSWORD on/off menu.
When a password is set for MyScreen:
• The MyScreen registration function (and menu) will be unavailable.
• The MyScreen Lock menu will be unavailable.
• The START UP setting will be locked on MyScreen (and the menu will be 
unavailable).
Turning the MyScreen PASSWORD off will allow normal operation of these 
functions.
• Please do not forget your MyScreen PASSWORD.
2 Turning off the MyScreen PASSWORD2-1   Follow the procedure in 1-1 to display the MyScreen  PASSWORD on/off 
menu.
2-2 
  Select OFF to display the ENTER 
PASSWORD box (large). Enter the registered 
password and the screen will return to the 
MyScreen PASSWORD on/off menu.
If an incorrect PASSWORD is input, the menu will 
close. If necessary, repeat the process from 2-1.
3 If you have forgotten your password3-1   Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off 
menu.
3-2   Select OFF to display the ENTER PASSWORD box (large). The 10 digit 
Inquiring Code will be displayed inside the box.
3-3   Contact your dealer with the 10 digit Inquiring Code. Your password will 
be sent after your user registration information is confirmed.
ENTER NEW PASSWORD 
box (small)
(continued on next page)
ENTER PASSWORD box  (large) 
						

							58
SECURITY menu
ItemDescription
PIN LOCK
PIN LOCK is a function which prevents the projector from being used unless 
a registered Code is input.
1 Turning on the PIN LOCK1-1   Use the ▲/▼ buttons on the SECURITY menu to 
select PIN LOCK and press the ► button or the 
ENTER button to display the PIN LOCK on/off 
menu.
1-2   Use the ▲/▼ buttons on the PIN LOCK on/
off menu to select ON and the Enter PIN 
Code box will be displayed. 
1-3   Input a 4 part PIN code using the ▲/▼/◄/►, 
COMPUTER or INPUT button. 
The PIN Code again box will appear. Reenter 
the same PIN code. This will complete the PIN 
code registration.
• If there is no key input for about 55 seconds   
while the Enter PIN Code box or the PIN Code again box is displayed, 
the menu will close. If necessary, repeat the process from 1-1.
Afterwards, anytime the projector is restarted after AC power  is turned off 
the Enter PIN Code box will be displayed. Enter the registered PIN code.
The projector can be used after entering the registered PIN code. If an 
incorrect PIN code is input, the Enter PIN code box will be displayed again.
If an incorrect PIN Code is input 3 times, the projector will turn off. Afterwards 
the projector will turn off every time an incorrect PIN code is input. The 
projector will also turn off if there is no key input for about 5 minutes while 
the Enter PIN code box is displayed.
This function will activate only when the projector is started after  AC power 
is turned off.
• Please do not forget your PIN code.
2 Turning off the PIN LOCK2-1   Follow the procedure in 1-1 to display the PIN LOCK on/off menu. 
2-2   Use the ▲/▼ buttons to select OFF and the Enter PIN Code box will be 
displayed.  
Enter the registered PIN code to turn the PIN LOCK function off.
If an incorrect PIN Code is input 3 times, the menu will close.
3 If you have forgotten your PIN Code3-1   While the Enter PIN Code box is displayed, press and hold the  RESET 
button for three seconds or press and hold the  INPUT button for 3 
seconds while pressing the ► button on the projector. 
The 10 digit Inquiring Code will be displayed.
• If there is no key input for about 5 minutes 
while the Inquiring Code is displayed, the 
projector will turn off.
3-2   Contact your dealer with the 10 digit Inquiring Code. Your PIN Code will 
be sent after your user registration information is confirmed.
(continued on next page) 
						

							59
SECURITY menu
ItemDescription
TRANSITION  DETECTOR
If this function is set to ON when the vertical angle of 
the projector or MIRROR setting at which the projector 
is turned on is different than the previously recorded, the 
TRANSITION DETECTOR ON alarm will be displayed 
and the projector will not display the input signal.
• To display the signal again, set this function OFF.
• After about 5 minutes of displaying the TRANSITION DETECTOR ON 
alarm, the lamp will turn off.
• Keystone adjustment feature has been prohibited as long as the  Transition 
Detector function is on.
1 Turning on the TRANSITION DETECTOR1-1   Use the ▲/▼ buttons on the SECURITY menu 
to select TRANSITION DETECTOR and press 
the ► or the  ENTER button to display the 
TRANSITION DETECTOR on/off menu.
1-2  
Use the ▲/▼ buttons on the TRANSITION 
DETECTOR on/off menu to select ON. Select 
ON and the current angle and MIRROR 
setting will be recorded. The ENTER NEW 
PASSWORD box (small) will be displayed.
1-3  Use the ▲/▼/◄/► buttons to enter a 
password. Move the cursor to the right side 
of the ENTER NEW PASSWORD box (small) 
and press the ► button to display the NEW 
PASSWORD AGAIN box, enter the same 
password again.
1-4   Move the cursor to the right side of the 
NEW PASSWORD AGAIN box and press 
the ► button to display the NOTE NEW 
PASSWORD box for about 30 seconds, 
please make note of the password during 
this time.
Pressing the ENTER button on the remote control or the ► button on the 
projector will return to the TRANSITION DETECTOR on/off menu.
• Please do not forget your TRANSITION DETECTOR password.
• This function will activate only when the projector is started after turning off 
the AC power.
• This feature may not function properly if the projector is not in a stable 
position when ON is selected.
2 Turning off the TRANSITION DETECTOR2-1  Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.2-2  Select OFF to display the ENTER 
PASSWORD box (large). Enter the registered 
password and the screen will return to the 
TRANSITION DETECTOR on/off menu.
If an incorrect password is input, the menu will 
close. If necessary, repeat the process from 2-1.
3 If you have forgotten your password3-1  Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.3-2   Select OFF to display the ENTER PASSWORD box (large). The 10 digit 
Inquiring Code will be displayed inside the box.
3-3   Contact your dealer with the 10 digit Inquiring Code. Your password will 
be sent after your user registration information is confirmed.
(continued on next page)
ENTER NEW PASSWORD 
box (small)
ENTER PASSWORD box  (large) 
						

							60
SECURITY menu
ItemDescription
MY TEXT 
PASSWORD
The MY TEXT PASSWORD function can prevent the MY TEXT from being 
overwritten. When the password is set for the MY TEXT;
• The MY TEXT DISPLAY menu will be unavailable, which can prohibit 
changing the DISPLAY setting.
• The MY TEXT WRITING menu will be unavailable, which can prevent the 
MY TEXT from being overwritten.
1 Turning on the MY TEXT PASSWORD1-1   Use the ▲/▼ buttons on the SECURITY menu to 
select the MY TEXT PASSWORD and press the 
► button to display the MY TEXT PASSWORD 
on/off menu.
1-2   Use the ▲/▼ buttons on the MY TEXT 
PASSWORD on/off menu to select ON. The 
ENTER NEW PASSWORD box (small) will 
be displayed.
1-3   Use the ▲/▼/◄/► buttons to enter the 
password. Move the cursor to the right side 
of the ENTER NEW PASSWORD box (small) 
and press the ► button to display the NEW 
PASSWORD AGAIN box, and then enter the 
same password again.
1-4   Move the cursor to the right side of the 
NEW PASSWORD AGAIN box and press 
► button to display the NOTE NEW 
PASSWORD box for about 30 seconds, then 
please make note of the password during 
this time.
Pressing the ENTER button on the remote control or ► button on the 
projector will return to the MY TEXT PASSWORD on/off menu. 
2 Turning off the MY TEXT PASSWORD2-1   Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off 
menu.
2-2   Select OFF to display the ENTER 
PASSWORD box (large). Enter the 
registered password and the screen will 
return to the MY TEXT PASSWORD on/off 
menu. 
If an incorrect password is input, the menu will close. 
If necessary, repeat the process from 2-1
3 If you have forgotten your password3-1   Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off 
menu.
3-2   Select OFF to display the ENTER PASSWORD box (large). The 10 digit 
inquiring code will be displayed inside the box. 
3-3   Contact your dealer with the 10 digit inquiring code. Your password will 
be sent after your user registration information is confirmed.
ENTER NEW PASSWORD  
box (small)
ENTER PASSWORD box  (large)
(continued on next page)