Hitachi Cp X2510n Projector Technical Manual
Here you can view all the pages of manual Hitachi Cp X2510n Projector Technical Manual. The Hitachi manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 1
1 NOTE • Be sure to check jack type, signal level, timing and resolution before connecting this projector to a PC. • Some PCs may have multiple display screen modes. Use of some of these modes will not be possible with this projector. • Depending on the input signal, full-size display may not be possible in some cases. Refer to the number of display pixels above. • Although the projector can display signals with resolution up to UXGA (1600x1200), the signal...
Page 2
2 Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Resolution (H x V) Horizontal signal timing (μs) Vertical signal timing (lines) Signal mode (A) (B)(C) (D) (a)(b) (c)(d) 720 x 400 2.0 3.020.3 1.0 342400 1 TEXT 640 x 480 3.81.925.4 0.6 233480 10VGA (60Hz) 640 x 480 1.34.120.3 0.8 328480 9VGA...
Page 3
3 BAT TERYLAN ACOMPUTER IN1, BCOMPUTER IN2, CMONITOR OUT D-sub 15pin mini shrink jack • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V. sync. signal: TTL level (positive/negative) • Composite sync. signal: TTL level • Video signal: -Y, Analog, 1.0±0.1Vp-p with composite sync, 75Ω terminated -Cb/Pb, Analog, 0.7±0.1Vp-p, 75Ω terminated -C r/Pr, Analog, 0.7±0.1Vp-p 75Ω terminated System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60 Pin Signal Pin Signal 1...
Page 4
4 BAT TERYLAN GS-VIDEO Mini DIN 4pin jack Pin Signal 1 Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator Color signal 0.300Vp-p (PAL/SECAM, burst) 75Ω terminator 2 Brightness signal, 1.0Vp-p, 75Ω terminator 3 Ground 4 Ground Connection to the ports (continued) 4 3 21 HVIDEO RCA jack • System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL60 • 1.0±0.1Vp-p, 75Ω terminator COMPONENT DY, ECb/Pb FCr/Pr RCA jack x3 • System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60 Port Signal Y Component video Y,...
Page 5
5 BAT TERYLAN Connection to the ports (continued) IAUDIO IN1, JAUDIO IN2 Ø3.5 stereo mini jack • 200 mVrms 47kΩ terminator AUDIO IN3 KR, LL RCA jack x2 • 200 mVrms 47kΩ terminator AUDIO OUT MR, NL RCA jack x2 • 200 mVrms 1kΩ output impedance I J MLNK
Page 6
6 BAT TERYLAN Connection to the ports (continued) OUSB USB B type jack Pin Signal 1 +5V 2 - Data 3 + Data 4 Ground43 12 PCONTROL D-sub 9pin plug • About the details of RS-232C communication, please refer to the following page. Pin Signal PinSignal PinSignal 1 (No connection) 4(No connection) 7RTS 2 RD 5Ground 8CTS 3 TD 6(No connection) 9(No connection) PO Q QLAN RJ-45 jack87654321 Pin Signal PinSignal PinSignal 1 TX+ 4- 7- 2 TX- 5- 8- 3 RX+ 6RX- 95 4 3 2 1 6 78
Page 7
7 BAT TERYLAN ::À:»:¼:Æ :© :™ :ž :˜:Ì:»:À:Æ:w :£ :˜:Ì:»:À:Æ:w :© Connection to the ports (continued) To input SCART RGB signal; ex. To input SCART RGB signal to the projector, use a SCART to RCA cable. Connect the plugs refer to above ex.. For more reference, please consult your dealer. SCART connector (jack) SCART cable (plug) RCA plugs To input component video signal to COMPUTER IN ports ex. To input component video signal to the COMPUTER IN1 or IN2 port of the projector, use a RCA to D-sub...
Page 8
8 CD (1) (1) µ RD(2) (2) RD TD (3) (3) TD DTR (4) (4) µ GND (5) (5) GND DSR (6) (6) µ RTS (7) (7) RTS DTS (8) (8) CTS RI (9) (9) µ RS-232C Communication RS-232C Communication When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer . For details of RS-232C commands, refer to RS-232C Communication / Network command table ( &17). Connection 1. Turn off the projector and the computer. 2....
Page 9
9 RS-232C Communication (continued) Communicaion settings 1. Protocol 19200bps,8N1 2. Command format ("h" shows hexadecimal) Byte Number01 2345 6 7 8910 11 12 Command ActionHeader Data Header code Packet DatasizeCRC flag Action TypeSetting code L H LH LH LH LH LH Change setting to desired value [(cL)(cH)] by [(eL)(eH)]. BEh EFh 03h06h00h(aL) (aH) 01h00h(bL)(bH) (cL)(cH) Read projector internal setup value [(bL) (bH)] .(aL) (aH) 02h00h(bL)(bH) 00h 00h Increment setup value [(bL)(bH)] by...
Page 10
10 RS-232C Communication (continued) 3. Response code / Error code ("h" shows hexadecimal) (1) ACK reply : 06h When the projector receives the Set, Increment, Decrement or Execute command correctly, the projector changes the setting data for the specified item by [Type], and it returns the code. (2) NAK reply : 15h When the projector cannot understand the received command, the projector returns the error code. In such a case, check the sending code and send the same command again. (3)...