Hitachi CP-X1200/CP-X1250 Projector User Manual

31
Multifunctional Settings (continued)
Multifunctional Settings (continued)
SCREEN Menu
With the SCREEN menu, the items shown in the table below can be
performed. Perform each operation in accordance with the
instructions in the table below.
: 
SELECT
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION
NETWORK BLANK
START UP
MyScreen
MyScreen SIZE
MyScreen LOCK
MENU POSITION
MESSAGE
RESET BLACK
ORIGINAL
x1
TURN OFF
TURN ON
ItemDescription
BLANK
Select a type of the BLANK screen using the  /  buttons....

32
Multifunctional Settings (continued) Multifunctional Settings (continued)
ItemDescription
MESSAGE
Select the TURN ON or the TURN OFF using the  /  buttons. :
TURN ON 
TURN OFF
When the TURN ON is selected, the following message function works.
The message of the “AUTO IN PROGRESS” for the auto adjustment. 
The message of the ”NO INPUT IS DETECTED”
The message of the ”SYNC IS OUT OF RANGE”
The message of the ”Searching …”
The message of the “Detecting …”
The indication of the input signal by input...

33
Multifunctional Settings (continued)
Multifunctional Settings (continued)
OPTION Menu
With the  OPTION menu, the items shown in the table below can be
performed. Perform each operation in accordance with the
instructions in the table below.
: 
SELECT
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION
NETWORKV OLUME
SPEAKER
IR REMOTE
IR REMOTE ID
LAMP TIME
FILTER TIME
SERVICE
RESET 16
TURN ON
ALL
1234 h
4321 h
ItemDescription
VOLUMEAdjust the volume using the  /  buttons. : 
High  
Low...

34
Multifunctional Settings (continued) Multifunctional Settings (continued)
ItemDescription
SERVICE
Pressing the (or the ENTER) button calls the SERVICE
menu. 
SERVICE Menu
Select an item using the  /  buttons, and press the
(or the ENTER) button to per form each function. :
FANSPEED 
AUTO ADJUST 
LENS TYPE 
LENS LOCK
FANSPEED
Select the fan speed level using the  /  buttons. :
HIGH 
NORMAL
The HIGH ups rotation speeds of fans, though. Please use this
function in using a projector at highlands etc....

35
Multifunctional Settings (continued) Multifunctional Settings (continued)
NETWORK Menu
This projector provides the NETWORK function. If you use this
function, please set up the projector according to the Network
environment in which you use it.
memoWhen you use a Network suitable to the DHCP function, the following
operation is not required commonly, because the TURN ON is selected to
the item “DHCP” at the shipment time. Please see the section “Network
Setting Up”.: SELECT
MENU
MAIN
PICTURE-1...

36
Network Setting Up
Network Setting Up
This projector provides the NETWORK function. If you use this function, \
please consult
your dealer for information.
To start, connect the NETWORK port to a gateway device via a RJ-45 (10B\
ASE-1) cable,
then set up the projector according to the Network environment in which \
you use it.
When you use a Network unsuitable to the DHCP functionPlease set the IP Address, the Subnet Mask, the Gateway and the DHCP (o\
n/off) using
the NETWORK menu, referring to the...

37
Lamp Lamp
The projector uses a high-pressure mercury glass lamp. The lamp can break with aloud bang, or burn out,if jolted or scratched, handled while hot, or worn over time.
Note that each lamp has a different lifetime, and some may burst or burn out soon after
you start using them. In addition, when the bulb bursts, it is possible for shards of
glassto fly into the lamp housing, and for gas containing mercuryto escape from the
projector’s vent holes.
About disposal of a lamp• This product contains a...

38
Lamp (continued) Lamp (continued)
After making sure that the projector has cooled
adequately, slide the knob of a lamp cover lock as
shown in the Figure. Then, one side of the lamp
cover is raised. Pull up the lamp cover and remove
it, as shown in the Figure. If the indicators or a message prompts you to replace the lamp, replace the lamp as soon
as possible.
Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at
least 45 minutes.
2
1
Contact your dealer to prepare a new...

39
Caring For The Air Filter 
Air Filter Air Filter
WARNING• Please carefully read the “User’s Manual - Safety Guide.
• Before caring, make sure the power switch is off and the power cable is not
plugged in, then wait at least 45 minutes for the lamp to cool sufficiently.
• Use only the air filter of the specified type NJ08081
.
• Do not use the projector with the air filter and filter cover removed. The use without
the air filter could result in damage.
CAUTION
• If the air filter becomes clogged by...

40
Other Care Other Care
WARNING• Please carefully read the “User’s Manual - Safety Guide”.
• Before caring, make sure the power switch is off and the power cable is not
plugged in.
• Be cautious of high temperature. Do not touch about the lens and ventilation
openings during use or immediately after use prevent a burn. 
• Never try to care for the inside of the unit yourself. Doing so is dangerous.
CAUTION
• Incorrect care could have adverse influence such as discoloration,
peeling paint, etc. 
• Do not...