Hitachi Cp-Rx60 Users Manual

							
51

Phenomena that may easily be mistaken for machine defects (continued)

Phenomenon
Cases not involving a machine defect
Reference

page 



No pictures are 

displayed.

The lens 
cover
 is closed.
cover is closed.cover

Remove the lens
cover
.
4
, 
1
6

The signal cables are not correctly connected.

Correctly connect the connection cables.
13, 14

The brightness is adjusted to an extremely low level.

Adjust the BRIGHT to a higher level using the menu function

or the remote control
.

25, 27

The 
computer
 cannot detect the projector as a plug 
computer cannot detect the projector as a plug computer

and play monitor.

Make sure that the 
computer’s
 can detect a plug and play 

monitor using other plug and play monitor.

1
3

Colors have a

faded- out

appearance, or

Color tone is 

poor.

Color settings are not correctly adjusted.

Perform picture adjustments by changing the COLOR 

TEMP, 
COLOR
, 
TINT and/or 
COLOR SPAC
E
settin
gs, 

using the menu functions.

2
5
, 
28 

32

COLOR SPACE setting is not suitable.

Change the COLOR SPACE setting to AUTO, RGB, 

SMPTE240 , REC709 or REC601. 

3
2

Pictures appear 

dark.

The brightness and/or contrast are adjusted to an 

extremely low level.

Adjust the BRIGHT and/or CONTRAST settings to a higher 

level using the menu function.

2
5
, 
2
7

The WHISPER function is working.

Select the NORMAL to the item WHISPER in the SETUP 

menu.

2
6
, 
3
4

The lamp is approaching the end of its product 

lifetime.

Replace the lamp.

41, 42, 

44

Pictures appear

blurry.

Either the focus and/or horizontal phase settings are 

not properly.

Adjust the focus using the focus 
ring
, and/or H PHASE 

using the menu function.

1
9
, 
30

The lens is dirty or misty.

Clean the lens by referring to the section “
Carin
g
f
or 
for f
t
he 

l
en
s
”.

4
5

Troubleshooting
NOTE  • Although bright spots or dark spots may appear on the screen, this 
is a unique characteristic of liquid crystal displays, and such do not constitute or 
imply a machine defect. 
						

							
52

Specifi cations
NOTE  • This specifi cations are subject to change without notice.
Warranty and after-ser vice / Specifi cations
Warranty and after-service
If a problem occurs with the equipment, fi rst refer to the “Troubleshooting” (46) and 
run through the suggested checks. If this does not resolve the problem, please contact 
your dealer or the service company. They will tell you what warranty condition is 
applied.
ItemSpecifi cation
Product nameLiquid crystal projector
Liquid
Crystal
panel
Panel size1.5 cm (0.6 type)
Drive systemTFT active matrix
Pixels786,432 pixels (1024 horizontal x 768 vertical)
LensF=1.77  f=20.4 mm
Lamp165W UHB
Power SupplyAC100-120V/2.7A, AC220-240V/1.5A
Power Consumption240W
Temperature range5 ~ 35°C (Operating)
Size
285 (W) x 73 (H) x 202 (D) mm 
(Not including protruding parts)
• Please refer to the following fi gure.
Weight (mass)2.2 kg
Ports
Optional 
parts
LampDT00701
Air fi lterNJ20922
Others• Please consult your dealer.
RGB input:  RGB .....D-sub 15pin mini x 1
Communication port:  CONTROL ........  CONTROL ........  CONTROLD-sub 9pin x 1
Video input:  VIDEO .....................RCA x 1  S-VIDEO  ...........S-Video x 1
Audio input:  AUDIO ..........Stereo mini x 1 
						

							
53

Specifi cations
Specifi cations (continued)
[unit: mm][unit: mm]
202
28569
33.57383