Hitachi Cp-Rx60 Users Manual

							
41

Maintenance
Maintenance
Lamp
 WARNINGHIGH VOLTAGEHIGH TEMPERATUREHIGH PRESSURE
►The  projector  uses  a  high-pressure  mercury  glass  lamp.  The  lamp  can break 
with  a  loud  bang,  or  burn  outwith  a  loud  bang,  or  burn  out,  if  jolted  or  scratched,  handled  while  hot,  or  worn over  time.  Note  that  each  lamp  has  a  different  lifetime,  and  some  may  burst  or burn  out  soon  after  you  start  using  them.  In  addition,  when  the  bulb  bursts,  it  is possible  for shards  of  glassshards  of  glass  to  fl y  into  the  lamp  housing,  and  for gas  containing gas  containing mercurymercury to escape from the projector’s vent holes.
►About disposal of a lamp • This product contains a mercury lamp; do not 
put in trash. Dispose of in accord with environmental laws.For lamp recycling, go to www.lamprecycle.org. (in the US) For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada). For more information, call your dealer.
• If  the  lamp  should  break  (it  will  make  a  loud  bang  when  it  does), 
unplug  the  power  cord  from  the  outlet,  and  make  sure  to  request  a replacement  lamp  from  your  local  dealer.  Note  that  shards  of  glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.•  If  the  lamp  should  break  (it  will  make  a  loud  bang  when  it  does), ventilate  the  room  well,  and  make  sure  not  to  breathe  the  gas  that comes out of the projector vents, or get it in your eyes or mouth.• Before replacing the lamp, turn the projector off and unplug the power cord,  then  wait  at  least  45  minutes  for  the  lamp  to  cool  sufficiently. Handling  the  lamp  while  hot  can  cause  burns,  as  well  as  damaging  the lamp.
• Never unscrew except the appointed (marked by an arrow) screws.
•  Do  not  open  the  lamp  cover  while  the  projector  is  suspended  from above.  This  is  dangerous,  since  if  the  lamp’s  bulb  has  broken,  the shards  will  fall  out  when  the  cover  is  opened.  In  addition,  working  in high  places  is  dangerous,  so  ask  your  local  dealer  to  have  the  lamp replaced even if the bulb is not broken.•  Do  not  use  the  projector  with  the  lamp  cover  removed. At  the  lamp replacing,  make  sure  that  the  screws  are  screwed  in  firmly.  Loose screws could result in damage or injury.
• Use only the lamp of the specifi ed type.
•  If  the  lamp  breaks  soon  after  the  first  time  it  is  used,  it  is  possible that  there  are  electrical  problems  elsewhere  besides  the  lamp.  If  this happens, contact your local dealer or a service representative.• Handle with care: jolting or scratching could cause the lamp bulb to bur st during use.•  If  the  indicators  or  a  message  prompts  you  to  replace  the  lamp  (see the  section  "Related  Messages"  and  "Regarding  the  indicator  Lamps"), replace  the  lamp  as  soon  as  possible.  Using  the  lamp  for  long  periods 
of  time,  or  past  the  replacement  date,  could  cause  it  to  burst.  Do  not use old (used) lamps; this is a cause of breakage.
Disconnect the plug from the power outlet 
						

							
42

Lamp (continued)

When the indicators or a message prompts you to replace the lamp, replace the 

lamp as soon as possible.

1. 
Turn the projector off, and unplug the power cord. Allow the lamp to cool for 

at least 45 minutes.

2. 
To prepare a new lamp, contact your dealer and tell the lamp type number 

= 
DT00701
.  
If the projector is mounted on the ceiling, or if the lamp has 
If the projector is mounted on the ceiling, or if the lamp has 

broken, also ask the dealer to replace the lamp.
broken, also ask the dealer to replace the lamp.

In the case of replacement by yourself,

3. 
After making sure that the projector has cooled 

adequately, slowly turn over the projector, so 

that the bottom is facing up.

4. 
Please loosen the screw (marked by arrow). Then, 
unhook the claws of the lamp cover and remove the 
lamp cover.
5. Loosen the 2 screws (marked by arrow) of the lamp, 
and slowly pick up the lamp by the 
handles.
6. Insert the new lamp, and retighten 
fi rmly two screws that are loosened 
in the previous process to lock it in 
place.
7. Interlocking the 2 tabs of the lamp 
cover to the projector, position the 
lamp cover on the projector, and push the 
center point of two claws to fi x the lamp cover. 
Then retighten fi rmly the screw of the lamp 
cover.
8. Slowly turn the projector so that the top is 
facing up.
9. Turn the projector on, and reset the lamp time 
using the LAMP TIME function of OPTION 
menu (39).
NOTE  • When the lamp has been replaced after the message of "THE 
POWER WILL TURN OFF AFTER 0hr." is displayed, complete the following 
operation within 10 minutes of switching power on.
• Incorrectly resetting of the lamp timer (resetting without replacement, or 
neglect of resetting after replacement) will result in incorrect message functions.
Maintenance
Tabs
Screws marked by arrow
Center pointof claws
Claws of lamp cover
Screw marked by arrow  
						

							
43

Maintenance
When  the  indicators  or  a  message  prompts  you  to  clean  the  air  fi lter,  clean  the 
air  fi lter  as  soon  as  possible.  If  the  air  fi lter  becomes  clogged  by  dust  or  the  like, 
internal  temperatures  rise  and  the  power  may  be  automatically  turned  off  for 
malfunction prevention.
1. Disconnect all the connectors and adapters that were connected to the 
projector’s ports. Then slowly turn the projector so that the lens-side is facing 
up. Please be careful for a projector not to fall. While the projector is placed 
lens-side up, hold the projector.
2. Remove the fi lter cover and the air fi lter. Hold the knobs while pulling out it.
3. Apply a vacuum cleaner to the vent of the projector for the air fi lter. And then 
slowly turn the projector bottom up.
Usual fi lter cover
Filter cover’s knobs
Filter cover’s knobs
Air fi lter’s knob
WARNING  ►Do not replace the air fi lter during use or immediately after use. 
Handling while the projector is in a high temperature could cause a burn and/or 
malfunction to the projector. Before operating, make sure that the power switch is 
off, that the power cord is not plugged in, and that the projector is cool adequately.
►Use only the air fi lter of the specifi ed type. Do not use the projector with the 
air fi lter and fi lter cover removed.
►Avoid wetting the projector or inserting liquids in the projector. It could result 
in a fi re, an electric shock, and/or malfunction to the projector.
CAUTION  ►Please replace the air fi lter when it is damaged or too soiled, 
and also when you replace the lamp.
Air fi lter
Filter cover for bottom-up use    
						

							
44

Maintenance
Air fi lter (continued)
4. Apply a vacuum cleaner to the air fi lter and fi lter cover.
Then set a new or cleaned air fi lter into place.
In case of the fi lter cover for bottom-up use, remove the air fi lter from the fi lter 
cover and clean each. After cleaning, reattach the cleaned fi lter to the fi lter cover.
Please replace the air fi lter when it is damaged or too soiled.Please replace the air fi lter when it is damaged or too soiled.
To prepare a new air fi lter, contact your dealer and tell the air fi lter type number 
= NJ20922. 
An air fi lter of specifi ed type will come even with the replacement lamp for this 
projector.
5. Position the air fi lter and fi lter cover into place.
6. Slowly turn the projector so that the top is facing up, except for the case of 
bottom-up use.
7. Turn the projector on, and reset the fi lter time using the FILTER TIME function 
of OPTION menu. (39)
NOTE  • Incorrectly resetting of the fi lter timer (resetting without replacement, 
or neglect of resetting after replacement) will result in incorrect message 
functions.
ClawsAir fi lter
Rail of air fi lter
Filter cover for bottom-up use
Usual fi lter coverPush the points of “PUSH” word with claws to fi x the air fi lter.Interlocking the tabs, snap the fi lter cover into place.
Filter cover for bottom-up useInterlocking the tabs, snap the fi lter cover into place.
Tabs
Tabs     
						

							
45

Maintenance
WARNING  ►Do not take care of the projector during use or immediately after 
use. Handling while the projector is in a high temperature could cause a burn and/
or malfunction to the projector. Before operating, make sure that the power switch is 
off, that the power cord is not plugged in, and that the projector is cool adequately.
►Never try to care for the inside of the projector personally. Doing is so 
dangerous. 
►Avoid wetting the projector or inserting liquids in the projector. It could result 
in a fi re, an electric shock, and/or malfunction to the projector. 
• Don’t put a container containing water, cleaner or chemicals near the 
projector. 
• Don’t use aerosols or sprays.
CAUTION  ►Please take right care of the projector according to the 
following. Incorrect care could cause not only an injury but adverse infl uence 
such as discoloration, peeling paint, etc. 
• Do not use cleaner or chemicals other than those listed below. 
• Do not polish or wipe with hard objects.
Inside of the projector
In order to ensure the safe use of your projector, please have it cleaned and 
inspected by your dealer about once every year.
Caring for the lens
If the lens is fl awed, soiled or fogged, it could cause deterioration of display 
quality. Please take care of the lens, being cautious of the handling.
1. Turn the projector off, and unplug the power cord. Allow the projector to cool 
suffi ciently.
2. After making sure that the projector is cool adequately, lightly wipe the lens 
with a commercially available lens-cleaning wipe. Do not touch the lens 
directly with your hand.
Caring for the cabinet and remote control
Incorrect care could have adverse infl uence such as discoloration, peeling paint, 
etc.
1. Turn the projector off, and unplug the power cord. Allow the projector to cool 
suffi ciently.
2. After making sure that the projector is cool adequately, lightly wipe with gauze 
or a soft cloth.
If soiling is severe, dip soft cloth in water or a neutral cleaner dilute in water , 
and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.
Other care  
						

							
46

Troubleshooting
Troubleshooting
Related messages
When the unit's power is on, messages such as those shown below may be 
displayed. When any such message is displayed on the screen, please respond 
as described below. If the same message is displayed after the treatment, or if a 
message other than the following appears, please contact your dealer or service 
company.
Although these messages will be automatically disappeared around several 
minutes, it will be reappeared every time the power is turned on.
MessageDescription
CHANGE THE LAMP
AFTER REPLACING LAMP,  RESET THE LAMP TIMER.The time the lamp timer has counted is approaching 
2000 hours.
Preparation of a new lamp, and an early lamp change is 
recommended. After you have change the lamp, please be 
sure to reset the lamp timer. (39)
CHANGE THE LAMP
AFTER REPLACING LAMP,  RESET THE LAMP TIMER.
THE POWER WILL TURN OFF AFTER ** hr.The time the lamp timer has counted is approaching 
2000 hours, so a lamp change within ** hours is 
recommended.
When lamp usage reaches 2000 hours, the power will 
automatically be turned off. Please change the lamp by 
referring to the section “Lamp”. (41)  After you have 
changed the lamp, please be sure to reset the lamp timer. 
(39)
CHANGE THE LAMP
AFTER REPLACING LAMP,  RESET THE LAMP TIMER.
THE POWER WILL TURN OFF  AFTER 0 hr.As the time the lamp timer has counted has reached 
2000 hours, the power will soon be automatically 
turned off.
Please immediately turn the power off, and change the lamp 
by referring to the section “Lamp”.  (41)  After changing 
the lamp, please be sure to reset the lamp timer.  (39)
NO INPUT IS DETECTEDON ***
There is no input signal.
Please confi rm the signal input connection, and the status 
of the signal source.
SYNC IS OUT OF RANGEON ***  fH  *****kHz  fV  *****HzON ***  fH  *****kHz  fV  *****Hz
The horizontal or vertical wavelength of the inputted 
signal is outside of the response parameters of this unit.
Please confi rm the specs for this unit or the signal source specs. 
						

							
47

Troubleshooting
Related messages (continued)
MessageDescription
CHECK THE AIR FLOW
The internal portion temperature is rising.
Please turn the power OFF, and allow the unit to cool down 
at least 20 minutes. After having confi rmed the following 
items, please turn the power ON again.
 • Is there blockage of the air passage aperture?
• Is the air fi lter dirty?
 • Does the peripheral temperature exceed 35°C?
 • If the same indication is displayed after the treatment, 
please set the HIGH at the FAN SPEED of the item 
SERVICE of the OPTION menu.
CLEAN THE AIR FILTERPOWER OFF FIRST,
THEN CLEAN THE AIR  FILTER.
AFTER CLEANING THE AIR  FILTER,
RESET THE FILTER TIMER.A note of precaution when cleaning the air fi lter.
Please immediately turn the power OFF, and clean or 
change the air fi lter by referring to the “Air Filter” section of 
this manual. After you have cleaned or changed the air fi lter, 
please be sure to reset the fi lter timer  (39). 
NOTE  • A lamp has a fi nite product life. Lamps are characterized by the 
fact that, after long hours of usage, a lamp will no longer light up, or the lamp 
will break or burst, etc. This projector is equipped with an automatic shut-down 
function, such that the power will automatically be turned off when lamp usage 
time has reached 2000 hours. Please be aware, however, that among lamp 
types, there are major differences in product lifetimes; a lamp may thus fail to 
light even prior to the functioning of the automatic shut-down function of this 
projector. 
						

							
48

Troubleshooting
Regarding the indicator lamps
Lighting and fl ashing of the POWER indicator, the LAMP indicator, and the TEMP 
indicator have the meanings as described in the table below. Please respond 
in accordance with the instructions within the table. If the same indication is 
displayed after the treatment, or if an indication other than the following is 
displayed, please contact your dealer or service company.
POWER 
indicator
LAMP 
indicator
TEMP 
indicatorDescription
Lighting
InOrange
Turned
off
Turned
off
The projector is in a standby state.
Please refer to the section “Power On/Off”. (16)
Blinking
InGreen
Turned
off
Turned
off
The projector is warming up.
Please wait.
Lighting
InGreen
Turned
off
Turned
off
The projector is in an on state.
Ordinary operations may be performed.
Blinking
InOrange
Turned
off
Turned
off
The projector is cooling down.
Please wait.
Blinking
InRed
(discre-
tionary)
(discre-
tionary)
The projector is cooling down. A certain error 
has been detected.
Please wait until the POWER indicator fi nishes blink, 
and then perform the proper response measure using 
the item descriptions below as reference.
Blinking
InRed
or
Lighting
InRed
Lighting
InRed
Turned
off
The lamp does not light, and there is a 
possibility that interior portion has become 
heated.
Please turn the power off, and allow the unit to cool 
down at least 20 minutes. After the projector has 
suffi ciently cooled down, please make confi rmation of 
the following items, and then turn the power on again.
• Is there blockage of the air passage aperture?
• Is the air fi lter dirty?
• Does the peripheral temperature exceed 35°C?
If the same indication is displayed after the treatment, 
please change the lamp by referring to the section 
“Lamp”.(41)
Blinking
InRed
or
Lighting
InRed
Blinking
InRed
Turned
off
The lamp cover has not been properly fi xed The lamp cover has not been properly fi xed The lamp cover
(attached).
Please turn the power off, and allow the unit to cool 
down at least 45 minutes. After the projector has 
suffi ciently cooled down, please make confi rmation 
of the attachment state of the lamp cover. After 
performing any needed maintenance, turn the power 
on again. If the same indication is displayed after 
the treatment, please contact your dealer or service 
company. 
						

							
49

Troubleshooting
Regarding the indicator lamps (continued)
POWER 
indicator
LAMP 
indicator
TEMP 
indicatorDescription
Blinking
InRed
or
Lighting
InRed
Turned
off
Blinking
InRed
The cooling fan is not operating.
Please turn the power off, and allow the unit to cool 
down at least 20 minutes. After the projector has 
suffi ciently cooled down, please make confi rmation 
that no foreign matter has become caught in the fan, 
etc. and then turn the power on again.
If the same indication is displayed after the treatment, 
please contact your dealer or service company.
Blinking
InRed
or
Lighting
InRed
Turned
off
Lighting
InRed
There is a possibility that the interior portion 
has become heated.
Please turn the power off, and allow the unit to cool 
down at least 20 minutes. After the projector has 
suffi ciently cooled down, please make confi rmation of 
the following items, and then turn the power on again.
• Is there blockage of the air passage aperture?
• Is the air fi lter dirty?
• Does the peripheral temperature exceed 35°C?
If the same indication is displayed after the treatment, 
please set the HIGH at the FAN SPEED of the item 
SERVICE of the OPTION menu.(40)
Lighting
InGreen
Alternative
blinking in Red
There is a possibility that the interior portion 
has become overcooled.
Please use the unit within the usage temperature 
parameters (5°C to 35°C). After the treatment, resent 
the power to ON.
Lighting
InGreen
Simultaneous
blinking in Red
It is time to clean the air fi lter.
Please immediately turn the power OFF, and clean 
or change the air fi lter by referring to the section “Air 
Filter”. After cleaning or changed the air fi lter, please 
be sure to reset the fi lter timer. After the treatment, 
resent the power to ON.
NOTE  • When the interior portion has become overheated, for safety 
purposes, the power source is automatically turned off, and the indicator lamps 
may also be turned off. In such a case, press the “” (OFF) side of the power 
switch, and wait at least 45 minutes. After the projector has suffi ciently cooled 
down, please make confi rmation of the attachment state of the lamp and lamp 
cover, and then turn the power on again. 
						

							
50

Troubleshooting
Phenomena that may easily be mistaken for machine defects
WARNING  ►Never use the projector if abnormal operations such as 
smoke, strange odor, excessive sound, damaged casing or elements or cables, 
penetration of liquids or foreign matter, etc. should occur. In such cases, 
immediately turn off the power switch and then disconnect the power plug from 
the power outlet. After making sure that the smoke or odor has stopped, contact 
your dealer or service company.
1. Before requesting repair, please check in accordance with the following chart.  
This operation sometimes resolves your problem.
If the situation cannot be corrected, 
2. The projector’s microprocessor may need to be reset. Please push the restart 
switch by using a pin or similar. (17)
3. Some setting may be wrong. Please use the FACTORY RESET function of 
SERVICE menu in the OPTION menu (40) to reset all settings to factory 
default.
Then, if the problem is not removed after maintenance, please contact your dealer 
or service company.
PhenomenonCases not involving a machine defectReference
page 
Power does not 
come on.
The electrical power cord is not plugged in.
Correctly connect the power cord.15
The power switch is not set to the on position.
Set the power switch to [ | ] (On).16
The main power source has been interrupted during 
operation such as by a power outage (blackout), etc.
Please turn the power off, and allow the unit to cool down at 
least 20 minutes. After the projector has suffi ciently cooled 
down, please turn the power on again.
16, 17
Either there is no lamp and/or lamp cover, or either 
of these has not been properly fi xed.
Please turn the power off, and allow the unit to cool down at 
least 45 minutes. After the projector has suffi ciently cooled 
down, please make confi rmation of the attachment state of 
the lamp and lamp cover, and then turn the power on again.
41, 42