Hitachi C 10fr Manual
Here you can view all the pages of manual Hitachi C 10fr Manual. The Hitachi manuals for Saw are available online for free. You can easily download all the documents as PDF.
Page 21
– 21 – English Fig. HH Place a small amount of dry lubricant on the bevel gear (2). The screw rod (1) must be kept clean and free of sawdust, gum, pitch, and other contaminants for smooth operations. If excessive looseness is observed in any parts of the blade raising mechanism or tilting mechanism, contact Hitachi Authorized Service Center immediately. LUBRICATION All motor bearings are permanently lubricated at the factory and require no additional lubrication. On all mechanical parts of...
Page 22
– 22 – English TROUBLESHOOTING GUIDE WARNING To avoid injury from an accidental start, turn the switch OFF and always remove the plug from the power source before making any adjustments. • Consult Hitachi Authorized Service Center if for any reason the motor will not run. SYMPTOMPOSSIBLE CAUSESCORRECTIVE ACTION Saw will not start.1. Saw not plugged in. 2. Fuse blown or circuit breaker tripped. 3. Cord damaged. 1. Plug in saw. 2. Replace fuse or reset circuit breaker. 3. Have cord replaced by...
Page 23
– 23 – English PUSH STICK CONSTRUCTION ● This is a full-size drawing (actual size) ● Use good quality plywood or solid wood ● Use 1/2 in. or 3/4 in. material ● Push stick MUST be thinner than the width of material being cut Drill Hole For Hanging Notch To Prevent Hand From Slipping Cut Here To Push 1/2 in. Wood Cut Here To Push 3/4 in. Wood
Page 24
– 24 – English Parts No.I.D.DescriptionSize QTYParts No.I.D.DescriptionSize QTY72643408VHCORD CLAMP17265870KFGCR. RE. PAN HD. SCREWM5*0.8-12272643709JKWRENCH17265880KHZCAP HD. SQ.NECK BOLTM6*1.0-12232660409WWGUARD BRACKET17265890KJ4CAP HD. SQ.NECK BOLTM6*1.0-3517264380B23SADDLE17265900KJ5CAP HD. SQ.NECK BOLTM6*1.0-80 17264390B24SPRING17265960KMRHEX. NUTM5*0.8 T=4 17264400B27POINTER BRACKET17265970KMSHEX. NUTM6*1.0 T=5 37264410B2BNEEDLE POINTER17266000KMVHEX. NUTM10*1.5 T=8 13265460B2DSWITCH...
Page 25
– 25 – English 10” (255mm) JOBSITE TABLE SAW MODEL NO. C10FR
Page 26
– 26 – English 10” (255mm) JOBSITE TABLE SAW MODEL NO. C10FR PARTS LIST FOR STAND Parts No.I.D.DescriptionSize QTYParts No.I.D.DescriptionSize QTY 72635701ADWING NUT172676527DLHANDLE1 72635801AELEVELING PAD172676627DMBRACKET ASS’Y (RIGHT)1 7264770J4EFLAT WASHERφ6*13-1 472676727DVLEVELING PAD3 7264820J4WFLAT WASHERφ8.2*18-1.5472677027DZBRACKET ASS’Y (LEFT)1 7265030JAZWAVE WASHER272635627E6 HOOK1 7265540K7DCR. RE. ROUND WASHER HD....
Page 27
– 27 – English
Page 28
– 28 –
English
Issued by
Hitachi Koki Co., Ltd.
Shinagawa Intercity Tower A, 15-1, Konan 2-chome,
Minato-ku, Tokyo 108-6020, Japan
607Code No. C99135011Printed in Taiwan
All Hitachi manuals