Hitachi C 10fr Manual

							
–  21  – 
English

Fig. HH
Place a small amount of dry lubricant on the bevel gear 
(2). The screw rod (1) must be kept clean and free of 
sawdust, gum, pitch, and other contaminants for smooth 
operations.
If excessive looseness is observed in any parts of the 
blade raising mechanism or tilting mechanism, contact 
Hitachi Authorized Service Center immediately.
LUBRICATION
All motor bearings are permanently lubricated at the 
factory and require no additional lubrication.
On all mechanical parts of your table saw where a pivot 
or threaded rod are present, lubricate using graphite or 
silicone. These dry lubricants will not hold sawdust as 
would oil or grease.
MAINTENANCE
MAINTAINING YOUR TABLE SAW
GENERAL MAINTENANCE
For your own safety, turn the switch OFF and remove 
the switch key. Remove the plug from the power source 
outlet before maintaining or lubricating your saw.
1.  Clean out all sawdust that has accumulated inside 
the saw cabinet and the motor.
2.  Polish the saw table with an automotive wax to keep 
it clean and to make it easier to slide the workpiece.
3.  Clean cutting blades with pitch and gum remover.
4. A worn, cut, or damaged power cord should be 
replaced immediately.
All electrical or mechanical repairs should be attempted 
only by a trained repair technician. Contact Hitachi 
Authorized Service Center for service. Use only identical 
replacement parts. Any other parts may create a hazard.
5.  Use liquid dish washing detergent and water to clean 
all plastic parts.
     NOTE: Certain cleaning chemicals can damage 
plastic parts.
6.  Avoid use of cleaning chemicals or solvents, 
ammonia and household detergents containing 
ammonia.
BLADE RAISING AND TILTING MECHANISM (FIG. HH)
After each five hours of operation, the blade raising
mechanism and tilting mechanism should be checked 
for looseness, binding, or other abnormalities. With the 
saw dis-connected from the power source, turn the saw 
upside down and alternately pull upward and downward 
on the motor unit. Observe any movement of the motor
mounting mechanism. Looseness or play in the blade
raising screw (1) should be adjusted as follows:
1.  Using a wrench, loosen nut (2).
2.  Adjust nut (3) until it is finger-tight against the bracket
     (4), then back off the nut (3) 1/6 turn.
3. Tighten nut (2) with the wrench, while holding nut (3)
     in place. Maximum allowable play of screw rod (1) is
     0.16” (4 mm).
WARNING
WARNING
1
2
3
5
4 
						

							
–  22  – 
English

TROUBLESHOOTING GUIDE
WARNING
To avoid injury from an accidental start, turn the switch OFF and always remove the plug from the power 
source before making any adjustments.
• Consult Hitachi Authorized Service Center if for any reason the motor will not run.
SYMPTOMPOSSIBLE CAUSESCORRECTIVE ACTION
Saw will not start.1.  Saw not plugged in.
2.  Fuse blown or circuit breaker tripped.
3.  Cord damaged.
1.  Plug in saw.
2.  Replace fuse or reset circuit breaker.
3.  Have cord replaced by Hitachi 
Authorized Service Center.
Does not make accurate 45° 
and 90° rip cuts.
1.  Positive stop not adjusted correctly.
2.  Tilt angle pointer not set accurately.
1.  Check blade with square and adjust 
positive stop.
2.  Check blade with square and adjust to 
zero.
Material pinched blade when 
ripping.
1.  Rip fence not aligned with blade.
2.  Warped wood, edge against fence is not 
straight.
1.  Check and adjust rip fence.
2.  Select another piece of wood.
Material binds on splitter.1.  Splitter not aligned correctly with blade.1. Check and align splitter with blade.
Saw makes unsatisfactory 
cuts.
1.  Dull blade.
2.  Blade mounted backwards.
3.  Gum or pitch on blade.
4.  Incorrect blade for work being done.
5.  Gum or pitch on blade causing erratic 
feed.
1.  Replace blade.
2.  Turn the blade around.
3.  Remove blade and clean with 
turpentine and coarse steel wool.
4.  Change the blade.
5.  Clean table with turpentine and steel 
wool.
Material kicked back from 
blade.
1.  Rip fence out of adjustment.
2.  Splitter not aligned with blade.
3.  Feeding stock without rip fence.
4.  Splitter not in place.
5.  Dull blade.
6.  The operator letting go of material before 
it is past saw blade.
7.  Miter angle lock knob is not tight.
1.  Align rip fence with miter gauge slot.
2.  Align splitter with blade.
3.  Install and use rip fence.
4.  Install and use splitter. (with guard)
5.  Replace blade.
6.  Push material all the way past saw 
blade before releasing work.
7.  Tighten knob.
Blade does not raise or tilt 
freely.
1.  Sawdust and dirt in raising/tilting  
     mechanisms.
1.  Brush or blow out loose dust and dirt.
Blade does not come up to 
speed. 
1.  Extension cord too light or too long.
2.  Low house voltage.
1.  Replace with adequate size cord.
2.  Contact your electric company.
Machine vibrates excessively.1.  Saw not mounted securely to workbench.
2.  Bench on uneven floor.
3.  Damaged saw blade.
1.  Tighten all mounting hardware.
2.  Reposition on flat level surface. Fasten 
to floor if necessary.
3.  Replace blade.
Does not make accurate 45° 
and 90° crosscuts.
1.  Miter gauge out of adjustment.1.  Adjust miter gauge. 
						

							
–  23  – 
English

PUSH STICK CONSTRUCTION
●   This is a full-size drawing (actual size)
●   Use good quality plywood or solid wood
●   Use 1/2 in. or 3/4 in. material
●   Push stick MUST be thinner than the width 
of material being cut
Drill Hole For 
Hanging
Notch To Prevent
Hand From 
Slipping
Cut Here To 
Push 1/2 in. 
Wood
Cut Here To 
Push 3/4 in. 
Wood 
						

							
–  24  – 
English

Parts No.I.D.DescriptionSize QTYParts No.I.D.DescriptionSize QTY72643408VHCORD CLAMP17265870KFGCR. RE. PAN HD. SCREWM5*0.8-12272643709JKWRENCH17265880KHZCAP HD. SQ.NECK BOLTM6*1.0-12232660409WWGUARD BRACKET17265890KJ4CAP HD. SQ.NECK BOLTM6*1.0-3517264380B23SADDLE17265900KJ5CAP HD. SQ.NECK BOLTM6*1.0-80 17264390B24SPRING17265960KMRHEX. NUTM5*0.8 T=4 17264400B27POINTER BRACKET17265970KMSHEX. NUTM6*1.0 T=5 37264410B2BNEEDLE POINTER17266000KMVHEX. NUTM10*1.5 T=8 13265460B2DSWITCH BOX17266010KMWHEX. NUTM10*1.5 T=413265470B3GELECTROMAGNETIC DISTURBANCE UNITS17266030KMYHEX. NUTM8*1.25 T=6.5 17264430B3HINSERT17266050KNDHEX. NUTM5*0.8 T=427264440B3RWRENCH17266120KQJCROWN NUTM8*1.25 T=12.5 2
7264450B84WASHERD=φ18 17266150KQWLOCK NUTM5*0.8 T=527264460B99SPACER17266220KRXHEXAGON NUT AND FLAT WASHERM6*1.0 37264470B9CPLUNGER HOUSING17266250KSWSTRAIN RELIEF17264480B9PCLAMP23264530KTHSTRAIN RELIEF27264490B9WBRACKET13257330KUXTERMINAL27264500BA4SPACER13264280KVQLEAD WIRE ASS’Y17264510BA9SPACER23265490LSFCIRCUIT BREAKER SWITCH17264520BAACLAMP13264580QQUCARBON BRUSH ASS’Y27264530BABSHIM13262430QR0BRUSH COVER27264540BACSET NUT17266420STEHEIGHT REGULATING BOLT ASS’Y17264550BAEARBOR COLLAR17266440T00SLIDING BASE ASS’Y27264560BATNUT172664910GPUPPER TUBE17264570BAUSUPPORTING PLATE132660510GVPOINTER17264580BAXSTIFFENER17263452178EXTENTION WING (RIGHT)17264590BAYSCREW BAR172665720WQHEX. HD. BOLTM6*1.0-5017264600BAZBEARING SEAT1726628212MLEAD WIRE ASS’Y17264610BB1SHAFT1726666216FSWITCH KEY17264620BB2PARRLE RING272666821BNBRACKET GROUP ASS’Y17564630BC2LOCATION SEAT2726695237UCOVER13265480F1HCOLLAR1726711238SPOINTER17624660GD0BLADE17263542771ANGLE ROD17264760J3UHEX WRENCH1726759275DEXTENTION WING17264780J4FFLAT WASHERφ8*16-2.51726760275EUPER TUBE27264790J4HFLAT WASHERφ10*30-0.22726761275FLOCATION SEAT27264830J5LFLAT WASHERφ5*10-0.310326606275JBATTERY BOX ASS’Y17264850J6TFLAT WASHER3/16*3/4-1/164726762275RLOCATION SEAT17264860J6UFLAT WASHER3/16*1/2-3/641726763275USPACER17264870J6VFLAT WASHER3/16*3/8-0.022872677827QVDEFLECTOR17264880J70FLAT WASHER1/4*3/4-7/642726782287HRETAINING CLIP17264900J76FLAT WASHER1/4*3/4-1/16472679028FKTABLE17264950J8DFLAT WASHER3/8*3/4-5/64272679628KXBODY SHELL17264970J95SPRING WASHERφ6 172679928L9LOCK KNOB17265000JAAWASHERφ8 172680228MCPARALLEL BRACKET ASS’Y17265010JAEEXTERNAL TOOTH LOCK WASHERφ4272680328MDMITER GAUGE ASS’Y17265020JAFEXTERNAL TOOTH LOCK WASHERφ5 172680428MGHANDWHEEL ASS’Y17265060JC9SPRING PIN172680528MHHANDWHEEL ASS’Y17265070JCASPRING PIN272632228N2BATTERY17265130JEDC-RING172681228PAKNOB17265150JEYE-RING132660728W4STICKER17265230JPBHEX. HD. BOLTM5*0.8-20 232660828W6STICKER 17265340JX7HEX. SOC. SET SCREWM6*1.0-6 432660928W7CAUTION LABEL 17265350JXLHEX. SOC. SET SCREWM10*1.5-12132661028WACAUTION LABEL17265320K0ZHEX. HD. SCREW AND WASHERM8*1.25-16432661128WBWARNING LABEL17265340K16HEX. HD. SCREW AND WASHERM8*1.25-16132661228WCWARNING LABEL17265380K25HEX. SOCKET HD. CAP SCREWSM5*0.8-20132661328WDCAUTION LABEL 17265430K3GCR. RE. PAN HD. SCREW & WASHERM5*0.8-12 132661428WGWARNING LABEL 17265490K57CR. RE. COUNT HD. SCREWM5*0.8-16132661528WLWARNING LABEL 17265570K7KCR. RE. ROUND WASHER HD. SCREWM6*1.0-12272686128X4BLADE GUARD ASS’Y17265610K8CCR. RE.COUNT HD. TAPPING SCREWM4*18-10432577228V2HEX. WASHER HD. BOLTM6*1.0-1627265620K8DCR. RE.COUNT HD. TAPPING SCREWM4*18-16272635529E2ROCKER SWITCH17265630K91CR. RE. TRUSS HD. TAPPING SCREWM4*16-12472629029PDWARNING LABEL 27265660K9THEX. HD. TAPPING SCREWM5*16-1663266162D8LFERRITE CORE 17265670K9UHEX. HD. TAPPING SCREWM5*16-2587262912DAUUPPER TUBE17265700KA4CR. RE. PAN HD. TAPPING SCREWM4*16-1623264382FSMCR. RE. PAN HD PLAIN WASHER TAPPING SCREWM5*0.8-823264370KBQCR. RE. PAN HD. TAPPING SCREWM5*16-1013265522H05POWER CABLE ASS’Y17265750KCACR. RE. TRUSS HD. TAPPING SCREWM5*12-1223266182HGWMOTOR17265760KCHCR.RE. PAN HEAD TAPPING & WASHER SCREWM5*0.8-12 23266192HKYRETAINING CLIP17265770KCXCR. RE. PAN HD PLAIN WASHER TAPPING SCREWM5*0.8-1043266202HKZSCALE17265780KCYCR. RE. PAN HD PLAIN WASHER TAPPING SCREWM5*0.8-12 43266212HL1SCALE17265810KDRCR. RE. PAN HD. SCREWM5*0.8-10 13266222HL2SCALE 17265820KDUCR. RE. PAN HD. SCREWM6*1.0-12 23266232HL3LABEL17265850KF6CR. RE. PAN HD. SCREWM4*0.7-823266242HS2BEVEL ANGLE ADJUSTMENT ASS’Y 1
PARTS LIST
10” (255mm) JOBSITE TABLE SAW                                               MODEL NO. C10FR
PARTS LIST FOR SCHEMATIC                        Always order by I.D. Number 
						

							
–  25  – 
English

10” (255mm) JOBSITE TABLE SAW                                               MODEL NO. C10FR 
						

							
–  26  – 
English

10” (255mm) JOBSITE TABLE SAW                                               MODEL NO. C10FR
PARTS LIST FOR STAND 
Parts No.I.D.DescriptionSize QTYParts No.I.D.DescriptionSize QTY
72635701ADWING NUT172676527DLHANDLE1
72635801AELEVELING PAD172676627DMBRACKET ASS’Y (RIGHT)1
7264770J4EFLAT WASHERφ6*13-1 472676727DVLEVELING PAD3
7264820J4WFLAT WASHERφ8.2*18-1.5472677027DZBRACKET ASS’Y (LEFT)1
7265030JAZWAVE WASHER272635627E6 HOOK1
7265540K7DCR. RE. ROUND WASHER HD. SCREWM6*1.0-10272677927RQCAP HD. SQ.NECK BOLTM8*1.25-404
7265590K7MCR. RE. ROUND WASHER HD. SCREWM6*1.0-18 172678027RRCR. RE. TRUSS HD. SCREWM6*1.0-464
7265800KDJCR. RE. PAN HD. SCREWM5*0.8-122726783288RHEX. HD. BOLTM8*1.25-554
7265810KDRCR. RE. PAN HD. SCREWM5*0.8-10472678428BUFLOOR PLATE1
7265940KKUCR. RE. PAN HD. ROUND NECK SCREWM5*08-10172678528BXCR. RE. PAN HD PLAIN WASHER TAPPING SCREWM5*0.8-104
7265970KMSHEX. NUTM6*1.0 T=5 172679728L2CLAMP HANDLE4
7266100KQ4WING NUTM8*1.25172679828L3FOLLOWER PLATE1
7266150KQWLOCK NUTM5*0.8 T=5 772683128VUHOOK2
7266160KQXNUTM6*1.0 T=6 472683228VVCONNECTOR1
7266170KQYLOCK NUTM8*1.25 T=8 672683328VXSUPPORTING TUBE ASS’Y1
726665213TROLLING WHEEL272683428VZLEVELING PAD1
72667322FZCAP HD. SQ.NECK BOLTM8*1.25-4523266172GRXDUST COLLECTOR ASS’Y1
72676427DJFOAM17268092EKGDUST BAG1 
						

							
–  27  – 
English 
						

							
–  28  – 
English
      Issued by
      Hitachi Koki Co., Ltd.
Shinagawa Intercity Tower A, 15-1, Konan 2-chome, 
             Minato-ku, Tokyo 108-6020, Japan
607Code No. C99135011Printed in Taiwan