Hitachi 55pd5200 Users Manual

19
ENGLISH
  Picture
  Audio
  Timer
  Function
  Setup
  Language
     Select
    OK  SetFunction
  Screen Saver    Off
  Screen Wipe  On  60Min.
  Black Side Panel    Off
  Video Power Save    Off
  Freeze Mode    Split
  Default Zoom    Panoramic  
  Reset       Reset
     Select            Set                Return
OK
    MENU
FUNCTION MENU
Function
  Panel Life      Normal
  Mode Display    Off
  ID Number      1
  Inverse    On  60Min.
  Standby White    Off
  Gamma      2.2  
  Reset       Reset...

Selected charactersSetup hint
Auto Adjust*(Menu)Adjust
Pressing the OK button here,
Automatic regulation is started.Horizontal Position, Vertical Position, Horizontal Clock and Clock
Phase are adjusted automatically. 
Horizontal Position
Moves the horizontal position
to left.Moves the horizontal position
to right.Adjust the left-side display position.
(This function is only for RGB2. It’s not available (grayed out) for
RGB1.)
Vertical Position
Moves down the vertical
position.Moves up the vertical...

21
ENGLISH
LANGUAGE MENU
  Picture
  Audio
  Timer
  Function
  Setup
  Language
     Select
   OK  SetLanguage
        English
        Français
        Deutsch
    Español   
    Italiano
    Norsk
    Svenska
       Select            Return          Exit
OK    MENU
Select a language by ▼▲
SELECT buttons and press the OK button.
OTHER FEATURES
Automatic Store
Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below.
•  The previously recorded items...

22
Signal Check
StatusDisplayAction
When Mode Display is set to ON,
the input signal is switched or
when the RECALL button is
pressed.A guide is displayed for the input
terminal and the horizontal and
vertical sync frequency.
When the sync signal is no longer
detected.•  A guide displays No Sync.
Signal, and Power Save (for
approx. 5 sec.)
•  When the condition continues
where the sync signal cannot be
detected, indicator lamp of
power source changes in
orange and the mode switches
to power save mode....

23
ENGLISH
NOTES
About screen defects
•  High precision technology is used in the making of plasma panels but there may be dark spots (points that do not illuminate) and bright spots
(points that are too bright) in some cases. These do not indicate a malfunction.
About residual images
•  In some cases, residual images may remain after the short-term display of still images and another image is displayed, but these will
disappear and return to normalcy. This is not a malfunction.
About the panel screen
•...

24
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed.  If the symptoms remain uncorrected, contact your dealer.
TROUBLESHOOTING
Customer servicing can be hazardous.
WARNING
SymptomPoint to checkSee page
•  No picture with the power-indicating lamp
off.• Check the way the power cable is connected.
•  Press the power switch.
•  The message “No Sync. Signal” or “Power
Save” is displayed.
•  No picture with the power indicating lamp
lights in...

25
ENGLISH
SymptomPoint to checkSee page
•  The temperature of the display panel surface is high.•  The plasma display panel is lighting the phosphors by the
discharge of internal radiation. In some cases, this may cause the
temperature of the panel surface to increase. Please note that this
is not a malfunction.
-
•  There are locations on the screen that are different from the
periphery (*).
*Points that do not light, points with brightness different
from that of the periphery, points with color...

26
Depending on the kind of system equipment used, images may not be displayed normally.  In this case, make the
adjustments suggested below. (only for RGB2)
Actions to Correct Abnormal Displays
Symptom 1Text displayed across the screen appears vertically streaked, with some characters blurred (figure 1).
The display image appears flowing (figure 2) (RGB input).
Example
ABC B
ABCDEFGHIJabcdefgABCDEFGabcdABCDEFGHIJabcdefgABCDEFGabcd
Vertical
streaksBefore adjustment
Some characters
are blurred.
After...

27
ENGLISH
Product specifications and designs are subject to change without notice.
PRODUCT SPECIFICATIONS
•  The monitor takes at least 30 minutes to attain the status of optimal picture quality.
Signal Input
RGB terminal (D-sub 15-pin connector)
12345
678910
1112131415
•  When different kinds of input signals are simultaneously input to
the monitor via a graphics board or the like, the monitor will
automatically select the signals in the following priority order:
*Even in the case of the recommended...

28
Signal Input (continued)
12345678
910111213141516
17 18 19 20 21 22 23
24
PRODUCT SPECIFICATIONS (continued)
DVI terminal (DVI-D)
PinInput signalPinInput signal
1T.M.D.S. Data2-14+5V Power
2T.M.D.S. Data2+15Ground (for+5V)
3T.M.D.S. Data2/4 Shield16Hot Plug Detect
4T.M.D.S. Data4-17T.M.D.S. Data0-
5T.M.D.S. Data4+18T.M.D.S. Data0+
6DDC Clock19T.M.D.S. Data0/5 Shield
7DDC Data20T.M.D.S. Data5-
8No Connect21T.M.D.S. Data5+
9T.M.D.S. Data1-22T.M.D.S. Clock Shield
10T.M.D.S. Data1+23T.M.D.S. Clock+...