Hanns G Hp222dj Users Manual

                                                                    User’s Manual  
SETTING THE MONITOR ON THE WALL 
DISSEMBLING THE STAND BASE: 
 
1. Disconnect all the cables and cords from  the Monitor to prevent breakage. 
2. Carefully place the Monitor face down on a soft and flat surface (blanket, foam, cloth, etc) to 
prevent any damage to the Monitor. 
3. Remove the four (4) screws so that the stand base can be removed. 
4. Gently remove the stand base.   
     
 
(For reference only) 
 
WALL...

User’s Manual 
 
MAKING CONNECTIONS 
 
CONNECTING TO A PC 
 
Turn off your computer before performing the procedure below.   
 
1. Connect one end of the VGA cable to the back of  the monitor and connect the other end to the 
computer’s VGA port. 
2.  Connect one end of the DVI cable (optional) to th e back of the monitor and connect the other end 
to the computer’s DVI port. 
3.  Connect the audio cable between the monitors  audio input and the PCs audio output (green 
port). 
4.  Plug one end of the...

                                                                    User’s Manual  
ADJUSTING THE VIEWING ANGLE 
 
•  For optimal viewing it is recommended to look at the full face of the monitor, then adjust the 
monitor’s angle to your own preference. 
•  Hold the stand so you do not topple the mon itor when you change the monitor’s angle. 
•  You are able to adjust the monitor’s angle from -5 ° to 15° . 
 
 
 
 
Figure.3.  Monitor Angle
 
 
NOTES: 
 
•  Do not touch the LCD screen when you change th...

User’s Manual 
 
OPERATING INSTRUCTIONS 
 
GENERAL INSTRUCTIONS   
   
Press the power button to turn the monitor on or off. The other control buttons are located on the 
front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to 
your personal preferences. 
•  The power cord should be connected. 
•  Connect the Signal cable from  the monitor to the VGA card. 
•  Press the power button to turn on the m onitor. The power indicator will light up. 
 
 
 
Menu /...

                                                                    User’s Manual  
FRONT PANEL CONTROL 
 
• Power Button: 
Press this button to switch ON/OFF of monitor’s power.   
 
• Power Indicator: 
Green  — Power On mode.  
Orange — Power Saving mode. 
 
•  MENU / RETURN:   
1. Turn the OSD menu on/off or re turn to the previous menu. 
2. Exit OSD menu when in volume OSD status. 
 
• Adjust < >:  
1. Adjust Brightness and volume when the OSD is off. 
2. Navigate through adjustment icons when OSD...

User’s Manual 
 
 
Resolution 
640x400@70Hz ↔ 720x400@70Hz 
640x400@85Hz ↔ 720x400@85Hz 
640x480@60Hz ↔ 720x480@60Hz 
1024x768@70Hz  ↔ 1280x768@70Hz 
1280x768@60Hz ↔1360x768@60Hz 
1400x1050@60Hz  ↔ 1680x1050@60Hz 
1400x1050@RB 60Hz  ↔ 1680x1050@RB 60Hz 
1400x1050@75Hz ↔ 1680x1050@75Hz 
1400x900@60Hz ↔ 1600x900@60Hz 
1360x768@60Hz ↔ 1366x768@60Hz 
** The screen resolutions available will depend on the purchased model.   
 
 
NOTES: 
 
•  Do not install the monitor in a location near heat  sources such as...

                                                                    User’s Manual  
HOW TO ADJUST A SETTINGS 
 
BRIGHTNESS/ CONTRAST 
BRIGHTNESS 
Adjust the brightness value of the display according to your 
preference. Select「BRIGHTNESS」option to adjust the 
brightness value. 
CONTRAST 
Adjust the contrast value of the display according to your 
preference. Select 「CONTRAST」option to adjust the contrast 
value. 
X-CONTRAST 
Optimal setting for high contrast  images or videos. The dark and 
light areas...

User’s Manual 
 
display, which does not ensure the image is shown as is or in 
initial scale. 「FIT」indicates scaling by the  proportion of original 
images, which may cause the screen showing black bands.  [The 
availability of this function depends upon the selected model]  
H-POSITION 
Select the 「H-POSITION 」option to shift the screen image to the 
left or right. Enter the op tion and adjust the level. [For VGA 
only] 
V-POSITION Select the  「V-POSITION 」option to shift the screen image up or 
down....

                                                                    User’s Manual  
the OSD. Enter the option and adjust the level.   
OSD TIME-OUT Select 「OSD TIME-OUT 」option to set the OSD time out from 
10 to 100 seconds. Enter the option and adjust the level. 
OSD COLOR 
To choose the color combination of the OSD window, select 
「OSD COLOR 」option under  「OSD SETTING 」menu, choose 
modes 1/2/3. 
SYSTEM 
AUDIO INPUT 
While transferring via the HDMI port, it is recommended to set 
AUDIO INPUT to...

User’s Manual 
 
PLUG AND  PLAY   
 
Plug & Play DDC2B Feature 
 
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. 
It allows the monitor to inform the host system  of its identity and, depending on the level of DDC 
used, communicate additional information about its display capabilities. The DDC2B is a 
bidirectional data channel based on the I²C protoc ol. The host can request EDID information over the 
DDC2B channel. 
 
THIS MONITOR WILL APPEAR TO BE NON-...