Haier Hw60-1201-u Manual

consumption AnD technicAl DAtA
TEChNICAL DATA
CONSUMPTION TABLE
The wash cycle times are intended as a guide only. The actual time used may vary due to different water pressure, initial water 
temperature, etc.WARNINg: Never overload the washing machine. See below for maximum loads. 
PROgRAM MAX. 
LOAd ENERgY 
CONSUMPTION WATER 
CONSUMPTION
TEMPERATUREWASHINg 
TIME
¬ Prewash 6kg/7kg/8kg
1.0kwh/0.945kwh/1.089kwh 74L/75L/78L40°C1:46
¬  6kg/7kg/8kg
0.75kwh/0.75kwh/0.76kwh 60L/56L/63L40°C1:28
¬...

WAshing methoDs
POwER SUPPL y
Connect the washing machine to the power supply (220V to 240V~/50Hz).
wATER CONNECTION
Turn on the tap. The water must be clean and clear.
Note: Before use, check for leakage in the joints between the tap and th\
e inlet hose 
by turning on the tap.
PREPARINg ThE LAUNDR y
¬  Sort out clothes according to fabric (cotton, synthetics, wool or silk) a\
nd to how dirty they are.
¬  Separate white clothes from coloured ones. Wash them first by hand to check if they fade or run.
¬...

LOADINg ThE MAChINE
Open the washer door, put in the laundry piece by piece. Close the door tightly. 
¬  When first using the washing machine, let it run unloaded for one program to prevent the laundry 
from being tainted by oil or dirty water from the washing machine. Before washing you should run the 
machine without laundry, but with detergent, with 60°C programm. 
¬  do not overload the washing machine.
SELECTINg DETERgENT
The washing efficiency and the performance is determined by the quality of...

SETTINg wAShINg TEMPERATURE
Press and hold down the temperature button until the desired temperature\
 is selected .
SETTINg SPIN SPEED
Press and hold down the speed button until the desired speed is selected\
.See "Operational functions" on the "Control 
panel" pages (08 and 09) for selecting temperature and spin speed. It \
is advisable to select the recommended value. 
wAShINg
Press the Start/Pause button. The washing machine will operate according to the preset\
 programs. The washing...

Bed sheet (single)Cotton Approximately 800g 
Blanket Wool Approximately 3000g 
Blended fabric clothes / Approximately 800g 
Jackets Cotton Approximately 800g 
Jeans / Approximately 800g 
Overalls Cotton Approximately 950g 
Ladies Pyjamas / Approximately 200g 
Shirts / Approximately 300g 
Socks Blended fabrics Approximately 50g 
T-Shirts Cotton Approximately 300g 
Underwear Blended fabrics Approximately 70g 
LOAD REfERENCE
CARE ChART
Resistant material 
delicate fabric
Washable at 95 °C
Washable at 60 °C...

1.2.
1.
2
.
cleAning & cAre
AfTER w AShINg
Turn off the water supply and pull out electricity plug after each wash. 
Open the washer door to prevent formation of moisture and odours. If 
the washing machine is left idle for a long period, drain the water in 
the machine and replace the drain hose.
CLEANINg ThE DETERgENT DRA wER
Clean the detergent distribution drawer regularly.
Swing out the drawer, flush it clean with water and then replace it.
CLEANINg ThE MAChINE
Unplug the machine during cleaning and...

wATER INLET vALvE AND INLET v ALvE fILTER
To prevent blockage to the water supply by ingress of foreign substances,\
 clean the water inlet valve and 
inlet valve filter regularly.        
MOvINg ThE MAChINE 
If the machine is to be moved to a distant location, replace the transpo\
rtation bolts removed before installation to prevent damage as 
shown below.
Remove the blanking plugs.
1. 
Remove the back cover
2. 
Insert the synthetic stabilisers and the transportation bolts.
3. 
Tighten the bolts with a...

DisplAy coDes
DISPLA y CODES AND SPECIAL fUNCTIONS
¬ Control panel lock function: Press the "delay" and the "Start/Pause" buttons simultaneously for 3 seconds after starting a program. 
It can no longer be changed by operating buttons or knobs. To unlock press the "delay" and "Start/Pause" buttons again for 3 
seconds.
¬ Power-off memory function: In case of abrupt power failure or the need to cut off the power during a program cycl\
e, the present 
settings will be saved...

trouBleshooting
TROUBLEShOOTINg
The following circumstances do not constitute problems. do not contact the Service Center until the problem has been confirmed.
PROBLEMCAUSES SOLUTIONS
Washing machine fails to 
operate. ¬ Poor connection to the power supply.
¬ Power failure.
¬ The washer door is not properly closed.
¬ Machine has not been switched on. _  Check connection to the power supply.
_  Check the power supply.
_  Close the washer door properly.
_  Make sure the machine is switched on.
Washing...

do not use a multiple socket extension cord. A separate earthed socket is required which shall be accessible at all times.
If the mains cord becomes damaged, it must be replaced by the manufactur\
er, its service agent or similarly qualified person with a 
lead of the same type and rating to avoid a hazard.
Never remove the plug from the socket by pulling on the cord, always gra\
sp the plug.
The door may get hot during use, do not touch it and keep children away \
whilst the machine is operating.
Never...