Global Garden Products Lawn Mower 102 - 122 102 - 122 Hydro Instructions Manual

102 - 122
6.4.0
REPLACEMENT OF THE DRIVE BELT





1 / 1
WORKSHOP MANUAL
page from 
2000to  ••••
6.4 REPLACEMENT OF THE DRIVE BELT

Dismantle the engine pulley [see 5.5] to release
the belt.

Remove the collector channel [see  5.3].
It is advisable to slacken the transmission belt to
work on the parts involved more easily.
This is done by  ...
➤In mechanical drive models:engaging the
parking brake.  
➤In hydrostatic drive models:slackening the
stretcher [see 4.4].
Dismantle the drive pulley
(1)and...

102 - 122
6.5.0- REPLACEMENT OF THE SMALL
WHEELS FOR THE DRIVE BELT




1 / 1
WORKSHOP MANUAL
page from 
2000to  ••••
6.5 REPLACEMENT OF THE SMALL WHEELS
FOR THE DRIVE BELT

Remove the collector channel [see  5.3].
It is advisable to slacken the transmission belt to
work on the parts involved more easily.
This is done by ...
➤In mechanical drive models:engaging the
parking brake. 
➤In hydrostatic drive models: slackening the
stretcher [see 4.4].
The small side wheels
(1), two or four depending on
the...

102 - 122
6.6.1- REPLACEMENT OF THE BLADES 
CONTROL BELT




1 / 1
WORKSHOP MANUAL
page from 
2002to  ••••
6.6 REPLACEMENT OF THE BLADES CONTROL
BELT
➤For models with lever operated engage-
ment: 
disengage the blades to slacken the belt.
Shift the mobile guide pulley
(1)forwards just
enough to free the belt 
(2)from the motor pulley
(3).
➤For models with electromagnetic clutch:
there is no pin(1)and it is enough to tug at a sec-
tion of the belt  to free it from the pulley.
Set the cutting deck to...

102 - 122
6.7.1- REPLACEMENT OF THE BLADES 
CONNECTION BELT




1 / 2
WORKSHOP MANUAL
page from 
2000to  ••••
6.7 REPLACEMENT OF THE BLADES 
CONNECTION BELT
Set the cutting deck to the lowest position to obtain
greater access, then slacken off and uncouple the
adjuster
(1) to unload the spring(2).
Dismantle the upper casing
(3), undo screw (4)and
dismantle the control pulley 
(5); undo the articula-
tion screw
(6)and remove the stretcher plate (7).
Remove the protection casing 
(8), slackening off...

102 - 122
6.7.1REPLACEMENT OF THE BLADES 
CONNECTION BELT




2 / 2
WORKSHOP MANUAL
page from 
2000to  ••••
Refit everything by reversing the operations
described above. Reset the adjuster reading
recorded previously and check that the blades are
at 90° to each other before locking the pin
(11)and
pulleys
(13)  and(14).
NOTE
On reassembly, check that the washer under the
pin (11) is not damaged and that the outer pin
rollers run freely.
Use the specific tool(15)# Code 60205001/0 to
check the piston...

TC•
TX
© by GLOBAL GARDEN PRODUCTS
102 - 122
6.8.0- REPLACEMENT OF THE BLADES 
ENGAGEMENT CABLE




1 / 1
WORKSHOP MANUAL
page from 
2000to  ••••
6.8 REPLACEMENT OF THE BLADES
ENGAGEMENT CABLE  (
➤For lever operat-
ed engagement models)

Remove the right-hand rear wheel [see 6.1].
With the cutting deck in the lowest position and the
lever in the disengaged position, loosen the
adjuster
(1), remove it from its housing and unhook
the spring
(2).
Take the end barrel
(3)off the fork(4)which is near
the...

102 - 122
6.9.0- REPLACEMENT OF THE SUPPORTS
AND  SHAFTS  OF THE BLADES




1 / 2
WORKSHOP MANUAL
page from 
2000to  ••••
6.9 REPLACEMENT OF THE SUPPORTS AND
SHAFTS  OF THE BLADES

Remove the cutting deck [see 5.7].
NOTE
This operation is not strictly necessary since, with a
little practice and experience, it is possible to dis-
mantle the deck supports without removing the
deck.

Remove the blades control belt and the blades
connection belt [see 6.6 - 6.7]

Remove the blades [see 4.10] and take off...

TC•
TX
© by GLOBAL GARDEN PRODUCTS
102 - 122
6.9.0- REPLACEMENT OF THE SUPPORTS
AND  SHAFTS  OF THE BLADES




2 / 2
WORKSHOP MANUAL
page from 
2000to  ••••
Refit the flanged supports onto the deck,fully
tightening the nuts (5)
and checking that the sup-
port with the longer shaft is on the left.
When refitting the plate 
(3),the holes correspond-
ing to the support axes must meet perfectly in
the centring step (15) 
cut into the upper part of
each support.
Tightening torques
2Plate fixing screws...

TC•
TX
© by GLOBAL GARDEN PRODUCTS
102 - 122
6.10.0
REPLACEMENT OF THE ACCELERATOR





1 / 1
WORKSHOP MANUAL
page from 
2000to  ••••
6.10 REPLACEMENT OF THE ACCELERATOR

Remove the dashboard [see 5.4].
Take off the knob
(1)and disconnect the cable(2)
from the connection terminal (3)on the engine.
Undo the two fixing screws 
(4)and take out the
accelerator together with the wire.
On reassembling, put the accelerator lever in the
«MINIMUM» position, connect the end of the cable
(2)to the terminal...

102 - 122
6.11.0- REPLACEMENT OF THE BRAKE PADS
AND DISC 




1 / 1
WORKSHOP MANUAL
page from 
2000to  ••••
6.11 REPLACEMENT OF THE BRAKE PADS
AND DISC  
( ➤In mechanical drive mod-
els)

Remove the left-hand rear wheel [see 6.1].
Disconnect the control rod
(1)from the lever (2)and
undo the two screws
(3)which hold on the support
(4).
The support 
(4)contains a pad (5a)separated from
the control pistons
(6)by a plate(7).
The other pad
(5b) can be reached by taking off the
disc 
(8).
If there is oil...