Gigabyte H110mm2 Manual

 &Ipv4	PXE	Support	 Enables	or	disables	IPv4	PXE	Support.	This	item	is	configurable	only	when	Network Stack is enabled.
 &Ipv4 HTTP Support	 Enables	or	disables	 HTTP	boot	 support	 for	IPv4.	 This	item	is	configurable	 only	when	Network Stack is enabled.
 &Ipv6	PXE	Support	 Enables	or	disables	IPv6	PXE	Support.	 This	item	is	configurable	only	when	Network Stack is enabled.
 &Ipv6 HTTP Support	 Enables	or	disables	 HTTP	boot	 support	 for	IPv6.	 This	item	is	configurable	 only	when	Network Stack is...

 &Aggressive	LPM	Support Enables or disables the power saving feature, ALPM (Aggressive Link Power Management), for the Chipset SATA controllers. (Default: Enabled)
 &Port 0/1/2/3 Enables or disables each SATA port. (Default: Enabled)
 &Hot	plug Enables or disable the hot plug capability for each SATA port. (Default: Disabled)
 &Configured	as	eSATA Enables or disables support for external SATA devices.
- 32 -  

 &VT-d (Note)
 Enables or disables Intel® Virtualization Technology for Directed I/O. (Default: Enabled)
 &Internal Graphics Enables or disables the onboard graphics function. (Default: Auto)
 &DVMT Pre-Allocated Allows you to set the onboard graphics memory size. Options are: 32M~1024M. (Default: 64M)
 &DVMT Total Gfx Mem Allows you to allocate the DVMT memory size of the onboard graphics. Options are: 128M, 256M, MAX. (Default: 256M)
 &Audio Controller Enables or disables the onboard audio function....

2-7 Power
 &Platform	Power	Management Enables or disables the Active State Power Management function (ASPM). (Default: Disabled)
 &PEG	 ASPM	 Allows	 you	to	configure	 the	ASPM	 mode	for	the	 device	 connected	 to	the	 CPU	 PEG	 bus.	This	 item	is	configurable	only	when	Platform	Power	Management	is set to Enabled. (Default: Enabled)
 &PCH ASPM	 Allows	 you	to	configure	 the	ASPM	 mode	for	the	 device	 connected	 to	Chipset's	 PCI	Express	 bus.	This	 item	is	configurable	only	when	Platform	Power...

 &Power On Password Set the password when Power On By Keyboard is set to Password. Press  on this item and set a password with up to 5 characters and then press  to accept. To turn on the system, enter the password and press . Note: To cancel the password, press  on this item. When prompted for the password, press  again without entering the password to clear the password settings.
 &Power On By Mouse Allows the system to be turned on by a PS/2 mouse wake-up event. Note: To use this function, you need an...

2-8	 Save	&	Exit
 &Save	&	Exit	Setup Press  on this item and select Yes. This saves the changes to the CMOS and exits the BIOS Setup program. Select No or press  to return to the BIOS Setup Main Menu.
 &Exit	Without	Saving Press  on this item and select Yes. This exits the BIOS Setup without saving the changes made in BIOS Setup to the CMOS. Select No or press  to return to the BIOS Setup Main Menu.
 &Load Optimized Defaults Press  on this item and select Yes to load the optimal BIOS default settings....

Chapter 3 Appendix
 •Before	installing	 the	drivers,	 first	install	 the	operating	 system.	(The	following	 instructions	 use	Windows 10 as the example operating system.) •After installing the operating system, insert the motherboard driver disk into your optical drive. Click on the message "Tap to choose what happens with this disc" on the top-right corner of the screen and select "Run Run.exe." (Or go to My Computer, double-click the optical drive and execute the Run.exe program.)...

Regulatory	Statements
Regulatory	NoticesThis document must not be copied without our written permission, and the contents there of must not be imparted to a third party nor be used for any unauthorized purpose.Contravention will be prosecuted. We believe that the information contained herein was accurate in all respects at the time of printing. GIGABYTE cannot, however, assume any responsibility for errors or omissions in this text. Also note that the information in this document is subject to change...

FCC Notice (U.S.A. Only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmf\
ul interference 
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy a\
nd, if not 
installed and used in accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no...

Contact Us
GIGA-BYTE	TECHNOLOGY	CO.,	LTD.Address: No.6, Baoqiang Rd., Xindian Dist., New Taipei City 231, TaiwanTEL: +886-2-8912- 4000, FA X: +886-2-8912- 4005Tech. and Non-Tech. Support (Sales/Marketing) : http://esupport.gigabyte.comWEB address (English): http://www.gigabyte.comWEB address (Chinese): http://www.gigabyte.tw
 •GIGABYTE	eSupport
To submit a technical or non-technical (Sales/Marketing) question, plea\
se link to: http://esupport.gigabyte.com
- 40 -