Gigabyte Ga8knxp Manual

IntroductionEnglish- 7 -On-Board SCSI RAID—Onboard Adaptec AIC-7902W chip
—Supports Disk striping (RAID0) or DISK Mirroring (RAID1)
—Supports Ultra 320 (320 MB/sec per channel)
—Supports 4 hard disk drives and 2 arrays per channelI/O Control—ITE8712PS/2 Connector—PS/2 Keyboard interface and PS/2 Mouse interfaceBIOS—Licensed AWARD BIOS
—Supports Dual BIOS—Supports Q-Flash
Additional Features—Supports CPU Dual Power System
—PS/2 Keyboard power on by password
—PS/2 Mouse power on
—External Modem wake up...

- 8 - GA-8KNXP Ultra-64 MotherboardEnglishCD_IN
GA-8KNXP Ultra-64KB_MS
COMA
LPT
USBLANATX_12VSOCKET 478 CPU_FAN
FDD
IDE1
IDE2
DDR2
COMBPWR_LED BAT PCI1
64PCI1
PCI2
F_USB1
ITE8712MAIN
BIOS
CODEC
PWR_FANHR
DDR3F_USB2
INFO_LINK F_AUDIO
IR_CIRIntel
KENAI II
WOL
VT6202BACKUP
BIOS
Adaptec
AIC-7902W SATA0_SBDDR4RAM_LED
ATXSYS_FAN
SCSI 1CINB_FAN
PCIX1
DDR1SPDIF_IO
SUR_CEN2X_DET R_USB
AUDIODDR5DDR6
SCSI 2F_PANEL GA-8KNXP Ultra-64 Motherboard Layout
CLR_CMOS SCSI_LED_CP4 Titan
AGP Intel®
 875P
DUAL CHANNEL DDR DDR...

IntroductionEnglish- 9 - Block DiagramCLK GENCPUCLK+/- (100/133/200MHz)
AGPCLK (66MHz)
MCHCLK (100/133/200mHz)
ICH3V66 (66MHz) PCICLK (33MHz)
USBCLK (48MHz)
14.318 MHz
33 MHzIntel 875PIntel
HRCPUCLK+/- (100/133/200MHz)
System Bus
800/533/400MHz
MCHCLK (100/133/200MHz)
66 MHz
33 MHz
14.318 MHz
48 MHz
LPC BUS AGP
4X/8X
AGPCLK
(66MHz)
3 PCI
2 PCI-X
RJ45
AC97 Link4 USB
PortsATA33/66/100
IDE ChannelsIntel
KENAI II
CSAITE871224 MHz
33 MHzFloppyLPT PortPS/2 KB/Mouse
2 COM Ports
MIC
LINE-INLINE-OUTPentium 4...

- 10 - GA-8KNXP Ultra-64 MotherboardEnglish 

Hardware Installation ProcessEnglish- 11 - To set up your computer, you must complete the following steps:
Step 1- Install the Central Processing Unit (CPU)
Step 2- Install memory modules
Step 3- Install expansion cards
Step 4- Install I/O Peripherals CablesChapter 2  Hardware Installation ProcessCongratulations! You have accomplished the hardware installation!
Turn on the power supply or connect the power cable to the power outlet. Continue with
the BIOS/software installation.Step 2Step 1Step 3Step...

- 12 - GA-8KNXP Ultra-64 MotherboardEnglishStep 1: Install the Central Processing Unit (CPU)
Step 1-1: CPU InstallationAngling the
rod to 650
1.Angling the rod to 65-degree maybe
feel a kind of tight , and then continue
pull the rod to 90-degree when a noise
cough  made.2. Pull the rod to the 90-degree directly.Pin1 indicator
3. CPU Top ViewPin1 indicator
4.Locate Pin 1 in the socket and
look for a (golden) cut edge on the
CPU upper corner. Then insert
the CPU into the socket. Socket
Actuation...

Hardware Installation ProcessEnglish- 13 - Step 1-2: CPU Cooling Fan Installation1.Fasten the cooling fan supporting-
base onto the CPU socket on the
motherboard. Before installing the CPU cooling fan, adhere to the following warning:
1.Please use Intel approved cooling fan.
2.We recommend you to apply the thermal tape to provide better heat
conduction between your CPU and cooling fan.
(The CPU cooling fan might stick to the CPU due to the hardening of
the thermal paste. During this condition if you try...

- 14 - GA-8KNXP Ultra-64 MotherboardEnglishBefore installing the memory modules, adhere to the following warning:
1.When RAM_LED is ON, do not install / remove DIMM from socket.
2.Please note that the DIMM module can only fit in one direction due to
the one notch. Wrong orientation will cause improper installation.
Please change the insert orientation.1.The DIMM socket has a notch, so the DIMM memory
module can only fit in one direction.
2.Insert the DIMM memory module vertically into the DIMM
socket....

Hardware Installation ProcessEnglish- 15 - Below are the explanations:
1.One, three, or five DDR memory modules are installed: The Dual Channel Technology
will not operate when one, three, or five DDR memory modules are installed and they
will only work as Single Channel.
2.Two DDR memory modules are installed (the same memory size and type): The Dual
Channel Technology will operate when two DDR memory modules are inserted indi-
vidually into Channel A and Channel B (DIMM 1 pairs up with DIMM 4, DIMM 2,...

- 16 - GA-8KNXP Ultra-64 MotherboardEnglish5.If six DDR memory modules are installed: To activate the Dual Channel Technology and
to make the size of each DDR memory module detected, please use six DDR memory
modules with identical size and type and insert them into the six DIMMs following the
sequence below:
DIMM 1: Double or Single Side
DIMM 2: Single Side
DIMM 3: Single Side
DIMM 4: Double or Single Side (if DIMM1 is inserted a double-side module, then DIIMM4
must also be inserted a double-side one.)...